A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and

A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and minimum values of the output waveform vout of the circuit are respectively

image
by

1 Answer

Answer :

A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and minimum values of the output waveform vout of the circuit are respectively +4V and-7V

by

Related questions

The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as?

Description : The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as

Last Answer : The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as non-linear circuit.

A unit step voltage is applied at t = 0 to a series RL circuit with zero initial conditions

Description : A unit step voltage is applied at t = 0 to a series RL circuit with zero initial conditions  A) It is possible for the current to be oscillatory B) The voltage across the resistor at t ... The energy stored in the inductor in the steady state is zero D) Theresistor current eventually falls to zero 

Last Answer : A

A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC

Description : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the

Last Answer : A DC voltage source is connected across a series RLC circuit. Under steady-state conditions, the applied DC voltage drops entirely across the C only

The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ.

Description : The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is A) 10 KHz B) 2.5 KHz C) 20 KHz D) 5 KHz

Last Answer : The frequency of the clock signal applied to the rising edge triggered D flip-flop shown in figure is 10 KHZ. The frequency of the signal at Q is 5 KHz

Assume that D1 and D2 in figure are ideal diodes. The value of current I is

Description : Assume that D1 and D2 in figure are ideal diodes. The value of current I is A)0mA B) 0.25mA C) 0.5 mA D)1.0mA 

Last Answer : Assume that D1 and D2 in figure are ideal diodes. The value of current I is 0mA

In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-16, if R1 has a value of 50 ohms and R2 has a value of 250 ohms and the input signal has a value of +10 millivolts, what is the value of the output signal?

Last Answer : 60 millivolts.

If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Description : If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Last Answer : If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

Consider the star network shown in figure. The resistance between terminals A and B with C open is 6 ohms,

Description : Consider the star network shown in figure. The resistance between terminals A and B with C open is 6 ohms, between terminals B and C withAopen is 11 ohms and between terminals C andAwith B open is 9 ohms. Then RA, RB, RC respectively is 

Last Answer : Consider the star network shown in figure. The resistance between terminals A and B with C open is 6 ohms, between terminals B and C withAopen is 11 ohms and between terminals C andAwith B open is 9 ohms. Then RA, RB, RC respectively is  2, 4,7

As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100.

Description : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

Last Answer : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is 50 A

Assume that the n—channel MOSFET shown in figure is ideal and that its threshold voltage is +1 .0 V.

Description : Assume that the n-channel MOSFET shown in figure is ideal and that its threshold voltage is +1 .0 V. The voltage Vab between nodes a and b is A)5V B)2V C)1V D)0V

Last Answer : Assume that the n-channel MOSFET shown in figure is ideal and that its threshold voltage is +1 .0 V. The voltage Vab between nodes a and b is 0V

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts

Last Answer : Answer: C

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total current in the circuit? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. .0011286 watts D. .014243 watts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the total power consumed by the circuit? EL-0036 A. 3.6 watts B. 72 watts C. .0011286 watts D. .014243 watts

Last Answer : Answer: D

In the illustration, the voltage applied to the circut is 12 VDC, the resistance for R1 is 10 ohms, and R2 is 10 ohms. What is the power consumed in 'R1' of the circuit shown in the illustration? EL-0036 A. 0.6 watts B. 3.6 watts C. 7.2 watts D. 120 watts

Description : In the illustration, the voltage applied to the circut is 12 VDC, the resistance for R1 is 10 ohms, and R2 is 10 ohms. What is the power consumed in 'R1' of the circuit shown in the illustration? EL-0036 A. 0.6 watts B. 3.6 watts C. 7.2 watts D. 120 watts

Last Answer : Answer: B

A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the

Description : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

Last Answer : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will not change

The internal resistances of an ideal current source, and an ideal voltage source are, respectively,

Description : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, (A) 0, ∞ (B) ∞, ∞ (C) ∞, 0 (D) 0,0

Last Answer : The internal resistances of an ideal current source, and an ideal voltage source are, respectively, ∞, 0

An ideal voltage source has?

Description : An ideal voltage source has?

Last Answer : An ideal voltage source has zero internal resistance.

An ideal voltage source should have?

Description : An ideal voltage source should have?

Last Answer : An ideal voltage source should have zero source resistance.

Assertion : In the circuit shown in figure, battery is ideal. If a resistance `R_(0)` is cannected in parallel with R, then power across R will increa

Description : Assertion : In the circuit shown in figure, battery is ideal. If a resistance `R_(0)` is cannected in parallel with R, then power across R will increa

Last Answer : Assertion : In the circuit shown in figure, battery is ideal. If a resistance `R_(0)` is cannected ... . D. If Assertion is false but Reason is true.

In the circuit shown in figure ammeter and voltmeter are ideal. If `E=4 V,R=9Omega` and `r=1Omega` then readings of ammeter and voltmeter are

Description : In the circuit shown in figure ammeter and voltmeter are ideal. If `E=4 V,R=9Omega` and `r=1Omega` then readings of ammeter and voltmeter are

Last Answer : In the circuit shown in figure ammeter and voltmeter are ideal. If `E=4 V,R=9Omega` and `r=1Omega` then readings of ... V C. 3 A, 4 V D. 4 A, 4 V

In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Last Answer : Answer: D

In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Description : In a circuit such as that shown in figure 3-15, if R1 has a value of 100 ohms and R2 has a value of 1 kilohm and the input signal is at a value of + 5 millivolts, what is the value of the output signal?

Last Answer : 50 millivolts.

In the circuit shown below, the current through the inductor is,

Description : In the circuit shown below, the current through the inductor is,

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an autotransformer B. operational amplifier whose output controls a step-up voltage reactor C. amplitude modulator whose output drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

If the line voltage to the controller shown in the illustration is 440 volts, what is applied across the control circuit? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts

Description : If the line voltage to the controller shown in the illustration is 440 volts, what is applied across the control circuit? EL-0080 A. 110 volts B. 220 volts C. 440 volts D. 660 volts

Last Answer : Answer: C

In a series RLC circuit at resonance, the magnitude of the voltage developed across the capacitor

Description : In a series RLC circuit at resonance, the magnitude of the voltage developed across the capacitor  A) Is always zero B) Can never be greater than the input voltage C) Can be greater than the input ... input voltage D) Can be greater than the input voltage, and is in phase with the input voltage

Last Answer : In a series RLC circuit at resonance, the magnitude of the voltage developed across the capacitor Can be greater than the input voltage, however, it is 90° out of phase with the input voltage 

In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage

Description : In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C?

Last Answer : In an ac series RLC circuit, the voltage across R and L is 20 V; voltage across L and C is 9 V and voltage across RLC is 15 V. What is the voltage across C? 7 V

In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal? In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Description : In the power amplifier shown in figure 2-10, what two signals are mixed to produce the output signal?

Last Answer : Local oscillator and coherent oscillator.

Which of the devices listed is indicated by the symbols lettered 'A' to 'F', shown in the illustration? EL-0016 A. Diodes B. Linear inductors C. Capacitors D. Transistors

Description : Which of the devices listed is indicated by the symbols lettered 'A' to 'F', shown in the illustration? EL-0016 A. Diodes B. Linear inductors C. Capacitors D. Transistors

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by R1? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the total power consumed by R1? EL-0036 A. 3.6 watts B. 72 watts C. 7.2 watts D. 36 watts

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R1? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R1? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 110 ohms, and R2 is 10 kohms what is the voltage measured across R1 EL-0036 A. 11.86 volts B. .131 volts C. 12 volts D. .673 volts

Last Answer : Answer: B

As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R2? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Description : As shown in the illustration if the applied voltage is 12 VDC, the resistance of R1 is 10 ohms, and R2 is 10 ohms what is the current flowing through R2? EL-0036 A. 0.6 amp B. 0.833 amp C. 1.2 amps D. 2.4 amps

Last Answer : Answer: A

A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = _:

Description : A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = _:  (1) Zero (2) Infinity (3) L/R (4) R/L 

Last Answer : A step voltage E is applied to a series R-L circuit. The rate of change of current is maximum at t = Zero.

Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or load resistor B. noise factor expressed in decibels C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signal D. S/N of an ideal system divided by S/N at the output of the receiver or amplifier under test, both working at the same temperature over the same bandwidth and fed from the same source

Description : Indicate the false statement. Noise figure is defined as A. the ratio of the S/N power supplied at the input terminal of a receiver or amplifier to the S/N power supplied to the output or ... under test, both working at the same temperature over the same bandwidth and fed from the same source

Last Answer : C. an unwanted form of energy tending to interfere with the proper and easy reception and reproduction of wanted signals

A circular loop of mass m and radius r in X-Y plane of a horizontal table as shown in figure. A uniform magnetic field B is applied parallel to X-axis

Description : A circular loop of mass m and radius r in X-Y plane of a horizontal table as shown in figure. A uniform magnetic field B is applied parallel to X-axis

Last Answer : A circular loop of mass m and radius r in X-Y plane of a horizontal table as shown in figure. A uniform ... . `(mg)/(2pirB)` D. `(pirB)/(mgl)`

Which of the following theorems can be applied to any network linear or non-linear, active or

Description : Which of the following theorems can be applied to any network linear or non-linear, active or passive, time variant or time invariant?   (a) Thevenin Theorem (b) Norton Theorem (c) Telligen Theorem (d) Superposition Theorem 

Last Answer : Which of the following theorems can be applied to any network linear or non-linear, active or passive, time variant or time invariant? (a) Thevenin Theorem (b) Norton Theorem (c) Telligen Theorem (d) Superposition Theorem 

Superposition theorem can be applied only to circuits having?

Description : Superposition theorem can be applied only to circuits having?

Last Answer : Superposition theorem can be applied only to circuits having linear bilateral elements.

Silicon diodes designed for a specific reverse breakdown voltage, become useful as an electronic power supply voltage regulator, called _____________. A. tunnel diodes B. hot-carrier diodes C. compensating diodes D. Zener diodes

Description : Silicon diodes designed for a specific reverse breakdown voltage, become useful as an electronic power supply voltage regulator, called _____________. A. tunnel diodes B. hot-carrier diodes C. compensating diodes D. Zener diodes

Last Answer : Answer: D

In a 3-phase voltage source inverter used for speed control of induction motor, anti-parallel diodes are used

Description : In a 3-phase voltage source inverter used for speed control of induction motor, anti-parallel diodes are used across each switching device. The main purpose of diodes is to:

Last Answer : In a 3-phase voltage source inverter used for speed control of induction motor, anti-parallel diodes are used across each switching device. The main purpose of diodes is to: Allow the motor to return energy during regeneration

Consider the following statements with regard to power diodes : 1. The breakdown voltage is directly...

Description : Consider the following statements with regard to power diodes : 1. The breakdown voltage is directly proportional to the doping density of the drift region. 2. Losses in the diode are ... vertically oriented structure supports large blocking voltages. Which of the above statements is/are correct ?

Last Answer : Consider the following statements with regard to power diodes : 1. The breakdown voltage is directly proportional to the doping density of the drift region. 2. Losses in the diode are less due to ... large blocking voltages. Which of the above statements is/are correct ? 2 only

The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Description : The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Last Answer : Answer: A

The number of diodes used in bridge rectifier circuit is (a) 4 (b) 3 (c) 2 (d)

Description : The number of diodes used in bridge rectifier circuit is (a) 4 (b) 3 (c) 2 (d)

Last Answer : (a) 4

Draw the circuit diagram for AND and OR gates using diodes.

Description : Draw the circuit diagram for AND and OR gates using diodes.

Last Answer : Diode AND gate :Diode OR gate : 

In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Description : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Last Answer : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3)) ... ` B. `90^(@)` C. `180^(@)` D. `60^(@)`

In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Description : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Last Answer : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt( ... 10 sqrt(2) A` C. `20 sqrt(2) A` D. `25 A`

In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Description : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3))/(2) mF`. Current in `L - R_(1)` circuit is

Last Answer : In the circuit shown in figure : `R = 10 Omega , L = (sqrt(3))/(10) H, R_(2) = 20 Omega` and `C = (sqrt(3) ... 2) A` C. `5 sqrt(6) A` D. `5 sqrt(3) A`

Resistance between points A and B in the circuit shown in figure is a. 4 ohm b. 6ohm c. 10 ohm d. 8 ohm

Description : Resistance between points A and B in the circuit shown in figure is a. 4 ohm b. 6ohm c. 10 ohm d. 8 ohm

Last Answer : c. 10 ohm

An electrical circuit with 10 branches and 7 junctions will have

Description : An electrical circuit with 10 branches and 7 junctions will have

Last Answer : An electrical circuit with 10 branches and 7 junctions will have  4 loop equations.

One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Description : One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Last Answer : B. Phase control