The door of a running refrigerator inside a room was left open. Which of the following statements is correct?  (a) The room will be cooled to the temperature inside the refrigerator.  (b) The room will be cooled very slightly.  (c) The room will be gradually warmed up.  (d) The temperature of the air in room will remain unaffected.  (e) any one of above is possible depending on the capacity.

The door of a running refrigerator inside a room was left open. Which of the following statements is correct?  (a) The room will be cooled to the temperature inside the refrigerator.  (b) The room will be cooled very slightly.  (c) The room will be gradually warmed up.  (d) The temperature of the air in room will remain unaffected.  (e) any one of above is possible depending on the capacity.
by

1 Answer

Answer :

Answer : c
by

Related questions

Why a room can be warmed by leaving open the door of an oven but cannot be cooled by leaving open the door of a kitchen refrigerator?

Description : Why a room can be warmed by leaving open the door of an oven but cannot be cooled by leaving open the door of a kitchen refrigerator?

Last Answer : the second law of thermodynamics proves that heat always flowsfrom hot to cold. It is hard to give good every day examples, sincewhen you open the refrigerator door you feel cold but actually theroom is warming the fridge.

The ideal efficiency of a Brayton cycle with regeneration, with increase in pressure ratio will  (a) increase  (b) decrease  (c) remain unchanged  (d) increase/decrease depending on ap-plication  (e) unpredictable. “

Description : The ideal efficiency of a Brayton cycle with regeneration, with increase in pressure ratio will  (a) increase  (b) decrease  (c) remain unchanged  (d) increase/decrease depending on ap-plication  (e) unpredictable. “

Last Answer : Answer : b

_________ is the temperature to which the air must be cooled, at constant pressure, to produce saturation.  a. relative humidity  b. triple point temperature  c. dew point  d. critical point

Description : _________ is the temperature to which the air must be cooled, at constant pressure, to produce saturation.  a. relative humidity  b. triple point temperature  c. dew point  d. critical point

Last Answer : dew point

It is a very hot day. You are in a special kitchen, in that there are no exits and the walls of this kitchen are thermally very well insulated. If you open the refrigerator door, the room will eventually: w) cool off. x) remain the same. y) heat up.

Description : It is a very hot day. You are in a special kitchen, in that there are no exits and the walls of this kitchen are thermally very well insulated. If you open the refrigerator door, the room will eventually: w) cool off. x) remain the same. y) heat up.

Last Answer : ANSWER: Y -- HEAT UP.

Ten cu. ft of air at 300psia and 400°F is cooled to 140°F at constant volume. What is the transferred heat?  a.-120Btu  b. -220Btu  c.-320Btu  d. -420Btu formula: Q= mcv(T2-T1)

Description : Ten cu. ft of air at 300psia and 400°F is cooled to 140°F at constant volume. What is the transferred heat?  a.-120Btu  b. -220Btu  c.-320Btu  d. -420Btu formula: Q= mcv(T2-T1)

Last Answer : -420Btu

Ten cu ft. of air at 300 psia 400°F is cooled to 140°F at constant volume. What is the final pressure? (formula: p2 = p1T2/T1)  a. 0  b. 209 psia  c. - 420 psia  d. None of the above

Description : Ten cu ft. of air at 300 psia 400°F is cooled to 140°F at constant volume. What is the final pressure? (formula: p2 = p1T2/T1)  a. 0  b. 209 psia  c. - 420 psia  d. None of the above

Last Answer : 209 psia

____________is the difference between the saturation temperature for the given pressure and the actual sub cooled liquid temperature.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Description : ____________is the difference between the saturation temperature for the given pressure and the actual sub cooled liquid temperature.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Last Answer : Degrees of Sub cooled, °SB

_____________ is the difference between the actual temperature of superheated vapor and the saturation temperature for the existing pressure.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Description : _____________ is the difference between the actual temperature of superheated vapor and the saturation temperature for the existing pressure.  a) Degrees of Superheat, °SH  b) Degrees of Sub cooled, °SB  c) Both a and b  d) None of the above

Last Answer : Degrees of Superheat, °SH

__________________ is a liquid at the saturations which has temperature equal to the boiling point corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Description : __________________ is a liquid at the saturations which has temperature equal to the boiling point corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Saturated Liquid

_________________ is one which has a pressure higher than the saturation pressure corresponding to the existing temperature.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Description : _________________ is one which has a pressure higher than the saturation pressure corresponding to the existing temperature.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Compressed Liquid

________________ is one which has a temperature lower than the saturation temperature corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Description : ________________ is one which has a temperature lower than the saturation temperature corresponding to the existing pressure.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Sub cooled Liquid

______________ is the temperature at which liquids start to boil or the temperature at which vapors begin to condense.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Description : ______________ is the temperature at which liquids start to boil or the temperature at which vapors begin to condense.  a. Saturation Temperature  b. Sub cooled Liquid  c. Compressed Liquid  d. Saturated Liquid

Last Answer : Saturation Temperature

The gas in a constant gas thermometer cooled to absolute zero would have _________.  a. no volume  b. no pressure  c. zero temperature at all scales  d. none of the above

Description : The gas in a constant gas thermometer cooled to absolute zero would have _________.  a. no volume  b. no pressure  c. zero temperature at all scales  d. none of the above

Last Answer : no pressure

The efficiency of Diesei cycle with decrease in cut off  (a) increases  (b) decreases  (c) remains unaffected  (d) first increases and then decreases  (e) first decreases and then increases.

Description : The efficiency of Diesei cycle with decrease in cut off  (a) increases  (b) decreases  (c) remains unaffected  (d) first increases and then decreases  (e) first decreases and then increases.

Last Answer : Answer : a

The flow through an open system is _________ if all properties at each point within the system remain constant with respect to time.  a. streamline flow  b. steady flow  c. constant flow  d. algebraic flow

Description : The flow through an open system is _________ if all properties at each point within the system remain constant with respect to time.  a. streamline flow  b. steady flow  c. constant flow  d. algebraic flow

Last Answer : steady flow

In an isothermal process, the internal energy of gas molecules  (a) increases  (b) decreases  (c) remains constant  (d) may increase/decrease depending on the properties of gas  (e) shows unpredictable behaviour.

Description : In an isothermal process, the internal energy of gas molecules  (a) increases  (b) decreases  (c) remains constant  (d) may increase/decrease depending on the properties of gas  (e) shows unpredictable behaviour.

Last Answer : Answer : c

Isochoric process is one in which  (a) free expansion takes place  (b) very little mechanical work is done by the system  (c) no mechanical work is done by the system  (d) all parameters remain constant

Description : Isochoric process is one in which  (a) free expansion takes place  (b) very little mechanical work is done by the system  (c) no mechanical work is done by the system  (d) all parameters remain constant

Last Answer : Answer : c

In thermodynamics, a throttling process, also called a _________, is a type of isenthalpic process where a liquid or gas is cooled as it passes from a higher pressure state to a lower pressure state.  a. Rankine Process  b. Carnot Cycle  c. Joule-Thomson process  d. Refrigeration process

Description : In thermodynamics, a throttling process, also called a _________, is a type of isenthalpic process where a liquid or gas is cooled as it passes from a higher pressure state to a lower pressure state.  a. Rankine Process  b. Carnot Cycle  c. Joule-Thomson process  d. Refrigeration process

Last Answer : Joule-Thomson process

What refers to the amount of heat removed from the cooled space in BTS’s for 1 watt-hour of electricity consumed?  A. Cost efficiency rating  B. Energy efficiency rating  C. Coefficient of performance  D. Cost of performance

Description : What refers to the amount of heat removed from the cooled space in BTS’s for 1 watt-hour of electricity consumed?  A. Cost efficiency rating  B. Energy efficiency rating  C. Coefficient of performance  D. Cost of performance

Last Answer : Energy efficiency rating

A manufacturer claims to have a heat engine capable of developing 20 h.p. by receiving heat input of 400 kcal/mt and working between the temperature limits of 227° C and 27° C. His claim is  (a) justified  (b) not possible  (c) may be possible with lot of sophistications  (d) cost will be very high  (e) theroretically possible.

Description : A manufacturer claims to have a heat engine capable of developing 20 h.p. by receiving heat input of 400 kcal/mt and working between the temperature limits of 227° C and 27° C. His claim is  ( ... be possible with lot of sophistications  (d) cost will be very high  (e) theroretically possible.

Last Answer : Answer : b

Which is NOT a correct statement?  A. A superheated vapor will not condense when small amount of heat re removed  B. An ideal gas is a gas that is not a superheated vapor  C. A saturated liquid can absorb as much heat as it can without vaporizing  D. Water at 1 atm and room temperature is subcooled

Description : Which is NOT a correct statement?  A. A superheated vapor will not condense when small amount of heat re removed  B. An ideal gas is a gas that is not a superheated vapor  C. A saturated ... absorb as much heat as it can without vaporizing  D. Water at 1 atm and room temperature is subcooled

Last Answer : An ideal gas is a gas that is not a superheated vapor

The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Description : The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Last Answer : Ans: a

The C.O.P of a refrigeration cycle with increase in evaporator temperature, keeping condenser temperature constant, will (a) increase (b) decrease (c) remain unaffected (d) may increase or decrease depending on the type of refrigerant used

Description : The C.O.P of a refrigeration cycle with increase in evaporator temperature, keeping condenser temperature constant, will (a) increase (b) decrease (c) remain unaffected (d) may increase or decrease depending on the type of refrigerant used

Last Answer : Ans: a

On opening the door of an operating refrigerator kept in a closed room, the temperature of the room will (A) Increase (B) Decrease (C) Remain same (D) Increase in summer and will decrease in winter

Description : On opening the door of an operating refrigerator kept in a closed room, the temperature of the room will (A) Increase (B) Decrease (C) Remain same (D) Increase in summer and will decrease in winter

Last Answer : (A) Increase

Which of the following best describes heat?  a. The capacity to do work  b. Forces times distances  c. Sum of thermal and chemical energy  d. An energy transfer due to temperature difference

Description : Which of the following best describes heat?  a. The capacity to do work  b. Forces times distances  c. Sum of thermal and chemical energy  d. An energy transfer due to temperature difference

Last Answer : An energy transfer due to temperature difference

The heat Q per unit mass per degree change in temperature that must be supplied or removed to change the temperature of a substance.  a. Specific Heat Capacity  b. Latent Heat  c. Heat of Transformation  d. Internal Heat

Description : The heat Q per unit mass per degree change in temperature that must be supplied or removed to change the temperature of a substance.  a. Specific Heat Capacity  b. Latent Heat  c. Heat of Transformation  d. Internal Heat

Last Answer : Specific Heat Capacity

The ______ of a substance is the amount of heat that must be added or removed from a unit mass of the substance to change its temperature by one degree.  A. Latent heat of fusion  B. Molar heat  C. Specific heat capacity  D. Specific heat

Description : The ______ of a substance is the amount of heat that must be added or removed from a unit mass of the substance to change its temperature by one degree.  A. Latent heat of fusion  B. Molar heat  C. Specific heat capacity  D. Specific heat

Last Answer : Specific heat capacity

What is defined as the energy required to raise the temperature of a unit mass of a substance by one degree?  A. Latent heat of fusion  B. Molar heat  C. Specific heat capacity  D. Specific heat

Description : What is defined as the energy required to raise the temperature of a unit mass of a substance by one degree?  A. Latent heat of fusion  B. Molar heat  C. Specific heat capacity  D. Specific heat

Last Answer : Specific heat

What refers to the amount of heat needed to raise the temperature of an object by one degree Celsius or 1K?  A. Heat capacity  B. Specific heat  C. Latent heat  D. Molar heat

Description : What refers to the amount of heat needed to raise the temperature of an object by one degree Celsius or 1K?  A. Heat capacity  B. Specific heat  C. Latent heat  D. Molar heat

Last Answer : Heat capacity

A zinc plate is attached to the knob of a negatively charged electroscope. What will happen to the leaves of the electroscope when ultraviolet light is shown on the zinc plate. Will the leaves: w) collapse at once x) gradually come together y) gradually spread further apart z) remain unaffected

Description : A zinc plate is attached to the knob of a negatively charged electroscope. What will happen to the leaves of the electroscope when ultraviolet light is shown on the zinc plate. Will the leaves: w) collapse at once x) gradually come together y) gradually spread further apart z) remain unaffected

Last Answer : ANSWER: X -- GRADUALLY COME TOGETHER

Two 12 ft. sections of aluminum siding are placed end to end on the outside wall of house. How large a gap should be left between the pieces to prevent buckling if the temperature can change by 55˚C?  a. 0.21 m  b. 0.18 m  c. 0.31 in  d. 0.18 in

Description : Two 12 ft. sections of aluminum siding are placed end to end on the outside wall of house. How large a gap should be left between the pieces to prevent buckling if the temperature can change by 55˚C?  a. 0.21 m  b. 0.18 m  c. 0.31 in  d. 0.18 in

Last Answer : 0.18 in

When an object undergoes thermal expansion,  a. any holes in the object expand as well  b. any holes in the object remain the same  c. mass increases  d. molecular activities would cease

Description : When an object undergoes thermal expansion,  a. any holes in the object expand as well  b. any holes in the object remain the same  c. mass increases  d. molecular activities would cease

Last Answer : any holes in the object expand as well

According to first law of thermodynamics  (a) work done by a system is equal to heat transferred by the system  (b) total internal energy of a system during a process remains constant  (c) internal energy, enthalpy and entropy during a process remain constant  (d) total energy of a system remains constant

Description : According to first law of thermodynamics  (a) work done by a system is equal to heat transferred by the system  (b) total internal energy of a system during a process remains constant  ( ... , enthalpy and entropy during a process remain constant  (d) total energy of a system remains constant

Last Answer : Answer : d

A wall of the firebrick has an inside temperature of 313ºF and an outside temperature of 73ºF. What is the difference in the surface temperature in Rankin?  a. 70  b. 68  c. 72  d. 94 ºR = ºF + 460

Description : A wall of the firebrick has an inside temperature of 313ºF and an outside temperature of 73ºF. What is the difference in the surface temperature in Rankin?  a. 70  b. 68  c. 72  d. 94 ºR = ºF + 460

Last Answer : 70

Carnot cycle efficiency is maximum when  (a) initial temperature is 0°K  (b) final temperature is 0°K  (c) difference between initial and final temperature is 0°K  (d) final temperature is 0°C  (e) initial temperature is minimum possible.

Description : Carnot cycle efficiency is maximum when  (a) initial temperature is 0°K  (b) final temperature is 0°K  (c) difference between initial and final temperature is 0°K  (d) final temperature is 0°C  (e) initial temperature is minimum possible.

Last Answer : Answer : b

An open system may refer to ______.  A. Control mass  B. Control volume  C. Control energy  D. Control temperature

Description : An open system may refer to ______.  A. Control mass  B. Control volume  C. Control energy  D. Control temperature

Last Answer : Control volume

Calorie is a measure of  (a) specific heat  (b) quantity of heat  (c) thermal capacity  (d)entropy  (e) work.

Description : Calorie is a measure of  (a) specific heat  (b) quantity of heat  (c) thermal capacity  (d)entropy  (e) work.

Last Answer : Answer : b

Total heat of a substance is also known as  (a) internal energy  (b) entropy  (c) thermal capacity  (d) enthalpy  (e) thermal conductance.

Description : Total heat of a substance is also known as  (a) internal energy  (b) entropy  (c) thermal capacity  (d) enthalpy  (e) thermal conductance.

Last Answer : Answer : d

Which of the following statements is TRUE for an ideal gas, but not for a real gas?  A. PV = nRT  B. An increase in temperature causes an increase in the kinetic energy of the gas  C. The total volume of molecules on a gas is nearly the same as the volume of the gas as a whole  D. No attractive forces exists between the molecule of a gas

Description : Which of the following statements is TRUE for an ideal gas, but not for a real gas?  A. PV = nRT  B. An increase in temperature causes an increase in the kinetic energy of the gas  C. The ... same as the volume of the gas as a whole  D. No attractive forces exists between the molecule of a gas

Last Answer : PV = nRT

The condensing pressure due to the presence of non-condensable gases, as compared to that actually required forcondensing temperatures without non-condensable gases, (a) will be higher (b) will be lower (c) will remain unaffected (d) may be higher or lower depending upon the nature of non-condensable gases

Description : The condensing pressure due to the presence of non-condensable gases, as compared to that actually required forcondensing temperatures without non-condensable gases, (a) will be higher (b) will be ... remain unaffected (d) may be higher or lower depending upon the nature of non-condensable gases

Last Answer : Ans: a

A train goes past a railway station at a high speed. A young boy standing on the edge of the platform is likely to _____? A. Fall away from the train B. Remain unaffected C. Fall towards the train D. Fall away from or towards the train depending upon the speed

Description : A train goes past a railway station at a high speed. A young boy standing on the edge of the platform is likely to _____? A. Fall away from the train B. Remain unaffected C. Fall towards the train D. Fall away from or towards the train depending upon the speed

Last Answer : ANSWER: C

A train goes past a railway station at a high speed. A young boy standing on the edge of the platform is likely to -----? A. Remain unaffected B. Fall away from the train C. Fall towards the train (Answer) D. Fall away from or towards the train depending upon the speed

Description : A train goes past a railway station at a high speed. A young boy standing on the edge of the platform is likely to -----? A. Remain unaffected B. Fall away from the train C. Fall towards the train (Answer) D. Fall away from or towards the train depending upon the speed

Last Answer : C. Fall towards the train (Answer)

The rise or depression of liquid in a tube due to surface tension will increase in size of tube will (A) Increase (B) Remain unaffected (C) May increase or decrease depending on the characteristics of liquid (D) Decrease

Description : The rise or depression of liquid in a tube due to surface tension will increase in size of tube will (A) Increase (B) Remain unaffected (C) May increase or decrease depending on the characteristics of liquid (D) Decrease

Last Answer : Answer: Option D

_________ the very small KE still present in molecules at absolute zero temperature.  a. internal KE  b. Atomic kinetic energy  c. Zero-Point Energy  d. Subliminal Energy

Description : _________ the very small KE still present in molecules at absolute zero temperature.  a. internal KE  b. Atomic kinetic energy  c. Zero-Point Energy  d. Subliminal Energy

Last Answer : Zero-Point Energy

Compressed air coming out from a punctured football  (a) becomes hotter  (b) becomes cooler1  (c) remains at the same temperature  (d) may become hotter or cooler depend-ing upon the humidity of the surround¬ing air  (e) attains atmospheric temperature.

Description : Compressed air coming out from a punctured football  (a) becomes hotter  (b) becomes cooler1  (c) remains at the same temperature  (d) may become hotter or cooler depend-ing upon the humidity of the surround¬ing air  (e) attains atmospheric temperature.

Last Answer : (b) becomes cooler1

The specific heat of air increases with increase in  (a) temperature  (b) pressure  (c) both pressure and temperature  (d) variation of its constituents  (e) air flow

Description : The specific heat of air increases with increase in  (a) temperature  (b) pressure  (c) both pressure and temperature  (d) variation of its constituents  (e) air flow

Last Answer : Answer : a

Which of the following can be regarded as gas so that gas laws could be applicable, within the commonly encountered temperature limits.  (a) 02, N2, steam, C02  (b) Oz, N2, water vapour  (c) S02, NH3, C02, moisture  (d) 02, N2, H2, air  (e) steam vapours, H2, C02.

Description : Which of the following can be regarded as gas so that gas laws could be applicable, within the commonly encountered temperature limits.  (a) 02, N2, steam, C02  (b) Oz, N2, water vapour  (c) S02, NH3, C02, moisture  (d) 02, N2, H2, air  (e) steam vapours, H2, C02.

Last Answer : Answer : d

A gas is compressed in a cylinder by a movable piston to a volume onehalf its original volume. During the process 300 kJ heat left the gas and internal energy remained same. The work done on gas in Nm will be  (a) 300 Nm  (b) 300,000 Nm  (c) 30 Nm  (d) 3000 Nm  (e) 30,000 Nm.

Description : A gas is compressed in a cylinder by a movable piston to a volume onehalf its original volume. During the process 300 kJ heat left the gas and internal energy remained same. The work done on gas in Nm will be  (a) 300 Nm  (b) 300,000 Nm  (c) 30 Nm  (d) 3000 Nm  (e) 30,000 Nm.

Last Answer : Answer : b

A plot of pressure vs. temperature for a given substance showing the various phases possible for that particular substance.  a. Phase diagram  b. P-T diagram  c. Wein Diagram  d. Histogram

Description : A plot of pressure vs. temperature for a given substance showing the various phases possible for that particular substance.  a. Phase diagram  b. P-T diagram  c. Wein Diagram  d. Histogram

Last Answer : Phase diagram

Entropy is the measure of:  a. The internal energy of a gas  b. The heat capacity of a substance  c. Randomness or disorder  d. The change of enthalpy of a system

Description : Entropy is the measure of:  a. The internal energy of a gas  b. The heat capacity of a substance  c. Randomness or disorder  d. The change of enthalpy of a system

Last Answer : Randomness or disorder