Description : Working width of disc plough can be increased by a) Disc angle b) Gang angle c) Vertical suction d) Horizontal clearance Ans. a
Last Answer : ans a
Description : In comparison to MB plough, the draft is less in disc plough because a) It roll over the soil instead of sliding b) It has lower contact area c) It has larger cutting edge d) None of these Ans. a
Description : The draft requirement in MB plough compared to disc plough for same depth of ploughing is: a) Less c) More b) Equal d) None of these
Last Answer : More
Description : During turning the traction while operating MB plough a) Plough should be lifted b) Plough should not be lifted c) Stop the tractor and lift the plough d) Unable to lift Ans. a
Description : The function of landside in mb plough is to a) Resist the side draft force b) Increase pulverization c) Decrease draft d) All of these Ans. a
Description : The two primary tillage equipments are 1. MB and disc harrow 2. Disc plough and disc harrow 3. Disc harrow and cultivator 4. MB and subsoiler
Last Answer : ans 4
Description : Dead furrow is made by 1. One way MB plough 2. 2 way MB plough 3. ridger 4. disc harrow
Last Answer : ans 1
Description : The two primary tillage equipments are A. MB and disc harrow B. Disc plough and disc harrow C. Disc harrow and cultivator. D. MB and. Subscriber
Last Answer : MB and disc harrow
Description : Dead furrow is made by A. One way MB plough. B. 2 way MB plough C. Ridger. D. Disc harrow
Last Answer : One way MB plough
Description : Jointer and coulter are the parts of :- A. Disc plough C. Indigenous plough B. Harrow plough D. MB plough
Last Answer : MB plough
Description : The penetration of a tandem disc harrow can be increased by a) Increasing tilt angle b) Increasing disc angle c) Increasing disc diameter d) All of the above Ans.c
Last Answer : Ans.c
Description : In a flail harvester, the cutting operation is performed by a) Horizontally rotating circular blades b) Vertically rotating circular blades c) Knives mounted on a horizontal shaft d) Knives mounted on a vertical shaft Ans. c
Last Answer : ans c
Description : The depth of penetration of a disc harrow is increased by: a) Tilt angle b) Gang angle c) Disc angle d) All of above
Last Answer : b) Gang angle
Description : Tandem disc Harrow is a disc Harrow comprising of four gangs in which each gang can be angle in… direction. a. Angular c. Parallel b. Opposite. d. Perpendicular
Last Answer : Opposite
Description : The gang angle of disc harrow is adjusted in the range of: a) 0-30 c) 30-60 b) 60-90 d) Above 90
Last Answer : B
Description : Disc angle adjustment influences: a. Depth of cut b. width of cut c. Soil break up d. Direction of travel
Last Answer : b. width of cut
Description : Select the types of Disc Plough? a) Standard disc Plough. c) Both a And b b) Vertical disc Plough. d) None of above
Last Answer : Both a And b
Description : . A Vertical disc plough is also termed as: a) Wheat plough c) Harrow plough b) Both (a) & (b) d) None of these
Last Answer : Both (a) & (b)
Description : Penetration of disc plough can be improved by a. Increasing disc angle b. Decreasing tilt angle c. Both a & b d. None of these
Last Answer : b. Decreasing tilt angle
Description : is the prime mover in which the direction of travel and its control for field operation is performed by the operator walking behind it. A. Power tiller C. Tillage B. Disc plough D. Rotary tiller
Last Answer : Power tiller
Description : The two primery tillage equipment a. MB plough and disc harrow b. Disc plough and disc harrow c. Disc harrow and cultivetor d. MB plough and subsoiler
Last Answer : d. MB plough and subsoiler
Description : Dead furrow is made by: a. One way MB plough b. Two way MB plough c. Ridger d. Disc harrow
Last Answer : a. One way MB plough
Description : A coulter attachment is used with: a. Disc harrow b. Seed drill c. MB plough d. Sub soiler
Last Answer : c. MB ploug
Description : .Land shipping become necessary often the following implments is used: a. MB plough b. Disc harrow c. Cultivator d. All of these
Last Answer : a. MB plough
Description : Disc angle in a standard disc plough varies from a. 25-35 ° c. 45-55 ° d. 55-65 °
Last Answer : Ans - b. 42-45 °
Description : The disc angle of a good plough varies between a) 25°-30° b) 10°-15° c) 18°-24° d) 42°-45°
Last Answer : 42°-45°
Description : Vetical suction of plough influences: a. Pulverization b. Depth of cut c. Width of cut d. Direction of cut
Last Answer : b. Depth of cut
Description : Vertical section of plough influences 1. Pulverization 2. Depth of cut 3. Width of cut 4. direction of pull
Last Answer : ans 2
Description : Vertical section of plough influence A. Pulverisation B. Depth of cut C. Width of cut. D. Direction of pull
Last Answer : Pulverisation
Description : Vertical section of plough influences A. Pulverization C. Width of cut B. Depth of cut D. Direction of pull
Last Answer : Depth of cut
Description : Functions of mold board plough a. Cutting the furrow slice. c) body to yoke b. Increase the depth of operation. d) length of the beam
Last Answer : Cutting the furrow slice.
Description : Penetration of a trailed type disc harrow is not affected by a) Size of disc b) Angle of disc c) Weight of disc d) Tractor hydraulic system Ans. d
Last Answer : Ans. d
Description : The plough bottom as combined unit consist of: a) None of these c) Coulter , jointer and frog b) Beam , handle and MB d) Share, landside , frog and MB
Last Answer : Share, landside , frog and Mb
Description : The required spacing between the disc on the gang bolt ranges from 15 to 25 cm for light duty and 25 to 30cm for heavy duty harrows is b. 25 to 35cm c. 25 to 40cm d. None of the above.
Last Answer : <!-- [endif] -->Ans - a. 25 to 30cm
Description : is a circular concave revolving steel plate using for cutting and inverting the soil. a. Gang bolt. c. Disc b. Bearing d. None
Last Answer : Bearing
Description : The flanked tube mounted on the gang bold between every two disc to prevent the lateral movement of the disc on the shaft is called............ a. Bearing. c. Gang bolt b. Gang. d. Spool
Last Answer : Spool
Description : The lateral movement of disc on shaft is called as A) Spool. C) Gang B) Bearing D) Gear
Description : In an offset disc harrow the angle between two gang is a) less than 90 degree b) 90 degree c) greater than 90 degree d) 180degree
Last Answer : a) less than 90 degre
Description : In disc harrow, the penetration of disc improves by: a) Increasing disc angle c) Lowering hitch point b) Regulating optimum speed d) All are correct
Last Answer : Increasing disc angle
Description : Ridger is also known as riding plough and moulds board plough. a. Single c. Half d. None of the above. Ans - b. Double
Last Answer : Ans - b. Double
Description : Which of the following in theodolite work is imperfect adjustment of the instrument (a) Error due to line of collimation being perpendicular to the horizontal axis (b) Error due to axis not to perpendicular ... to imperfect graduation (d) Error due to eccentricity of vernires (e) All of the above*
Last Answer : (e) All of the above*
Description : Which of the following is not a tractor drawn primary tillage tool? 1. Disc plough 2. rotavator 3. Country plough 4. Bar harrow
Last Answer : ans 3
Description : Which one of the following is not a secondary tillage tool? 1. Disc Plough 2. Disc harrow 3. Mould Board 4. none of these
Description : This type of plough penetrate deeper than the conventional cultivation machinery and break up the layers of the soil. a. Chisel plough b. Disc plough d. None of the above
Last Answer : Ans - c. sub-soiler plough
Description : It Is used for deep tillage and penetration of soil for storage for rain water in crop root zone. b. Disc plough c. Mould board plough d. None of the above
Last Answer : Ans- a. Chisel plough
Description : Mould board, disc, Chisel and Sub soil plough are the tillage equipments. b. Secondary c. post d. None of the above
Last Answer : Ans - a. Primary
Description : is a method of ploughing in which the soil broken and turn along the contours. a. Normal ploughing c. Contour ploughing b. Sub soil plough. d. Disc plough
Last Answer : Contour ploughing
Description : Standard disc Plough consists of steel disc of _ diameter a) 20 to 40 cm. c) 60 to 90 cm b) 30 to 60 cm. d) 70 to 100 cm
Last Answer : 60 to 90 cm
Description : Standerd disc plough consist of steel dics of… to……. CM diameter. a. 60,90 c) 60,80 b. 70,100. d) 70,90
Last Answer : 60,90
Description : is not a secondary tillage. A. Disc plough B. Plough C. Mould board D. None of these
Last Answer : disk plough,plough and mb plough are primary implement so answer is non of these