The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be: (1) 1/100 (2) 1/200 (3) 1/300 (4) 1/600 

1 Answer

Answer :

The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be: 1/300

Related questions

Description : The analog signal given below is sampled by 600 samples per second for m(t) = 3 sin 500 pt + 2 sin 700 pt then folding frequency is: (1) 500 Hz (2) 700 Hz (3) 300 Hz (4) 1400 Hz 

Last Answer : The analog signal given below is sampled by 600 samples per second for m(t) = 3 sin 500 pt + 2 sin 700 pt then folding frequency is: 300 Hz

Description : As per Nyquist criterion the sampling rate is (A) 2fs (B) (1/2)fs (C) (1/2fs) (D) (2/fs) Where fs is the signal frequency

Last Answer : (A) 2fs

Description : If the frequency spectrum of a signal has a bandwidth of500 Hz with thehighest frequency at 600 Hz, what shouldbe the samplingrate, according to the Nyquist theorem? A) 200 samples/s B) 500 samples/s C) 1000 samples/s D) 1200 samples/s

Last Answer : 1200 samples/s

Description : ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Last Answer : C. twice

Description : State sampling theorem. Define Nyquist rate.

Last Answer : SAMPLING THEOREM: Sampling theorem states that a band-limited signal of finite energy having the highest frequency component fm Hz can be represented and recovered completely from a set of samples taken ... frequency should be equal to or greater than twice the maximum signal frequency (fs≥ 2fm)

Description : According to D' Alembert's principle, m (d 2 x/ dt 2 ) + c (dx/dt) + Kx =0 is the differential equation for damped free vibrations having single degree of freedom. What will be the solution to this differential equation if the system is ... Φ) C x = (A - Bt) e - ωt D x = X e - ξωt (cos ω d t + Φ)

Last Answer : A x = (A + Bt) e – ωt

Description : According to D' Alembert's principle, m (d 2 x/ dt 2 ) + c (dx/dt) + Kx =0 is the differential equation for damped free vibrations having single degree of freedom. What will be the solution to this differential equation if the system is ... ) C. x = (A - Bt) e - ωt D. x = X e - ξωt (cos ω d t + Φ

Last Answer : A. x = (A + Bt) e – ωt

Description : According to D' Alembert's principle, m (d 2 x/ dt 2 ) + c (dx/dt) + Kx =0 is the A differential equation for damped free vibrations having single degree of freedom. What will be the solution to this differential equation if the system is ... (C)x = (A - Bt) e - ωt ( D )x = X e - ξωt (cos ω d t + Φ

Last Answer : ( A ) x = (A + Bt) e – ωt

Description : According to D' Alembert's principle, m (d 2 x/ dt 2 ) + c (dx/dt) + Kx =0 is the differential equati damped free vibrations having single degree of freedom. What will be the solution to this differ equation if the system is critically ... c. x = (A - Bt) e - ωt d. x = X e - ξωt (cos ω d t + Φ)

Last Answer : a. x = (A + Bt) e – ωt

Description : The most common technique to change an analog signal to digitaldata is called __________. A) PAL B) PCM C) sampling D) none of the abov

Last Answer : PCM

Description : The analog signal needs to be sampled at a minimum sampling rate of: (A) 2fs (B) 1/(2fs) (C) fs/2 (D) 2/fs

Last Answer : (A) 2fs

Description : Choosing a discrete value that is near but not exactly at the analog signal level leads to a) PCM error b) Quantization error c) PAM error d) Sampling error

Last Answer : b) Quantization error

Description : Find the electric field when the magnetic field is given by 2sin t in air. a) 8π x 10 -7 cos t b) 4π x 10 -7 sin t c) -8π x 10 -7 cos t d) -4π x 10 -7 sin t

Last Answer : a) 8π x 10 -7 cos t

Description : Calculate the emf of a material having flux density 5sin t in an area of 0.5 units. a) 2.5 sin t b) -2.5 cos t c) -5 sin t d) 5 cos t

Last Answer : d) 5 cos t

Description : The torque expression of a current carrying conductor is a) T = BIA cos θ b) T = BA cos θ c) T = BIA sin θ d) T = BA sin θ

Last Answer : c) T = BIA sin θ

Description : Indicate which of the following pulse modulation is analog  a) PCM b) DPCM c) PWM d) Delta

Last Answer : Indicate which of the following pulse modulation is analog  a) PCM b) DPCM c) PWM d) Delta

Description : If cosec |-sin |=l and sec |- cos |=m, prove that l2m2(l2+m2+3)=1 -Maths 9th

Last Answer : cosec(A) - sin(A) = l ⇒ 1/sin(A) - sin(A) = l ⇒ l² = 1/sin²(A) + sin²(A) - 2 --------- sec(A) - cos(A) = m ⇒ 1/cos(A) - cos(A) = m ⇒ m² = 1/cos²(A) + cos²(A) - 2 ---------- l²m² = [1/sin²(A) + ... A)) = = 1/(sin²(A)cos²(A)) ------------- ⇒ l²m² (l² + m² + 3) = sin²(A)cos²(A) / [sin²(A)cos²(A)] = 1

Description : Find the area of a right angled triangle with sides of 90 degree unit and the functions described by L = cos y and M = sin x. a) 0 b) 45 c) 90 d) 180

Last Answer : d) 180

Description : While measuring the distance between two points along upgrade with the help of a 20 m chain, the forward end of the chain is shifted forward through a distance (A) 20 (sin - 1) (B) 20 (cos - 1) (C) 20 (sec - 1) (D) 20 (cosec - 1)

Last Answer : (C) 20 (sec - 1)

Description : The Nyquist theorem specifies the minimum samplingrate to be_______. A) equal to the lowest frequency of asignal B) equal to the highest frequency ofa signal C) twice thebandwidth of a signal D) twice thehighest frequencyof a signal

Last Answer : twice thehighest frequencyof a signal

Description : Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Last Answer : (A) cos α = (dr + dp)/(dr + df)

Description : Given that sin A=1/2 and cos B=1/√2 then the value of (A + B) is: (a)30 (b)45 (c)75 (d)60

Last Answer : (c)75

Description : Identify the polarisation of the wave given, Ex = cos wt and Ey = sin wt. The phase difference is -90 0 . a) Left hand circularly polarised b) Right hand circularly polarised c) Left hand elliptically polarised d) Right hand elliptically polarised

Last Answer : b) Right hand circularly polarised

Description : Identify the polarisation of the wave given, Ex = 2 cos wt and Ey = 2 sin wt. The phase difference is +90 0 . a) Left hand circularly polarised b) Right hand circularly polarised c) Left hand elliptically polarised d) Right hand elliptically polarised

Last Answer : a) Left hand circularly polarised

Description : Identify the polarisation of the wave given, Ex = 2 cos wt and Ey = sin wt. The phase difference is -90 0 . a) Left hand circularly polarised b) Right hand circularly polarised c) Left hand elliptically polarised d) Right hand elliptically polarised

Last Answer : d) Right hand elliptically polarised

Description : Identify the polarisation of the wave given, Ex = Exo cos wt and Ey = Eyo sin wt. The phase difference is +90 0 . a) Left hand circularly polarised b) Right hand circularly polarised c) Left hand elliptically polarised d) Right hand elliptically polarised

Last Answer : c) Left hand elliptically polarised

Description : The Snell’s law is given by a) N1 sin θi = N2 sin θt b) N2 sin θi = N1 sin θt c) sin θi = sin θt d) N1 cos θi = N2 cos θt

Last Answer : a) N1 sin θi = N2 sin θt

Description : Given D = e -x sin y i – e -x cos y j Find divergence of D. a) 3 b) 2 c) 1 d) 0

Last Answer : d) 0

Description : If a cos theta plus b sin theta equals 8 and a sin theta - b cos theta equals 5 show that a squared plus b squared equals 89?

Last Answer : There is a hint to how to solve this in what is required to be shown: a and b are both squared.Ifa cos θ + b sin θ = 8a sin θ - b cos θ = 5then square both sides of each to get:a² cos² θ + 2ab cos ... + sin² θ) + b² (sin² θ + cos² θ) = 89using cos² θ + sin² θ = 1â†' a² + b² = 89

Description : Ventilating shafts are provided to a sewer line at every A. 100 m B. 150 m C. 200 m D. 300 m

Last Answer : ANS: D

Description : For large sewers, maximum distance between manholes may be A. 50 m B. 100 m C. 200 m D. 300 m

Last Answer : ANS: D

Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550

Last Answer : A. 575

Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 3 . Determine the static deflection of the shaft in mm. a) 0.147 b) 0.213 c) 0.132 d) 0.112

Last Answer : a) 0.147

Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Determine the frequency of transverse vibrations of the shaft. a) 31 b) 35 c) 37 d) 41

Last Answer : d) 41

Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550

Last Answer : a) 575

Description : Flat rate parcel rates Flat Rate Parcel Boxes size Dimension of boxes (in mm) Weight (in Kg.) Tariff (in Rs.) Small - S 250*50*300 0 to 1 125 Medium - M 250*100*300 Above 1 to 2.5 200 Large - L 300*250*200 Above 2.5 to 5 400

Last Answer : Large - L 300*250*200 Above 2.5 to 5 400

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

Description : The grade of concrete not recommended by I.S. : 456, is (A) M 100 (B) M 200 (C) M 300 (D) M 500

Last Answer : (D) M 500

Description : Transport of concrete by pumps, is done for a distance of (A) 100 m (B) 200 m (C) 300 m (D) 400 m

Last Answer : (D) 400

Description : Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2

Last Answer : (D) 300 kg/cm2

Description : In case of LWR track, full ballast section as specified in LWR Manual should be provided up to ……….. from the bridge abutment. a) 200 m b) 50 m c) 300 m d) 100 m*

Last Answer : d) 100 m

Description : Match List-I (crops) with List-II (water requirement) and select your answer from the code given below- List-I (a) Jowar (b) Soybean (c) Cotton (d) Groundnut List-II 1. 140 mm - 300 mm 2. 350 mm - 450 mm 3. 200 mm - 300 mm 4. 300 mm - ... (b) (c) (d) (A) 3 1 2 4 (B) 4 2 3 1 (C) 1 4 2 3 (D) 3 1 4 2

Last Answer : (C) 1 4 2 3

Description : Free board given in septic tank is about (a) 100 mm (b) 200 mm (c) 300 mm* (d) 500 mm

Last Answer : (c) 300 mm*

Description : 3.0 ml of raw sewage is diluted to 300 ml. The D.O. concentration of the diluted sample at the beginning of the test was 8 mg/l. After 5 dayincubation at 20°C, the D.O. concentration was 5 mg/l. The BOD of raw sewerage is A. 100 mg/l B. 200 mg/l C. 300 mg/l D. 400 mg/l

Last Answer : ANS: C

Description : If a 2% solution of sewage sample is incubated for 5 days at 20°C and the dissolved oxygen depletion was found to be 8 mg/l. The BOD of the sewage is A. 100 mg/l B. 200 mg/l C. 300 mg/l D. 400 mg/l

Last Answer : ANS: D

Description : Anil played 8 cricket matches. The mean (average) of the runs was found to be 80. After playing four more matches, the mean of the runs of all the matches was found to be 70. The total runs made in the last four matches is (A) 400 (B) 300 (C) 200 (D) 100

Last Answer : Answer: C

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

Description : The equation, NA = (DAB . Pt /RTZ . PBM) (PA1 - PA2 ) is for (A) Fick's second law of diffusion (B) Steady state diffusion for stagnant case (C) Liquid M.T.C. by Higbie penetration theory (D) None of these

Last Answer : (B) Steady state diffusion for stagnant case

Description : Explaining the derivatives of sin, cos and toa?

Last Answer : answer:I am assuming this isn't homework, as it is summer and from what you wrote it appears you are merely curious, so I think it's legal for me to do the proof here for you (don't strike me down, ... proof for that as well. By toa do you mean tangent? I can prove that one too if you'd like.

Description : What's the key to remembering how to draw each of the different trigonometric function graphs? (i.e. sin, cos, tan)

Last Answer : SOH – sin CAH – cos TOA – tan sin = opposite over hypotenuse cos = adjacent over hypotenuse tan = opposite over adjacent