In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary

In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: (1) 30 V (2) 60 V (3) 15 V (4) 10 V
by

1 Answer

Answer :

In a full wave rectifier circuit using centre tapped transformer, the peak voltage across half of the secondary winding is 30 V. Then PIV is: 60 V

by

Related questions

Draw and describe working of full wave rectifier using centre tapped transformer.

Description : Draw and describe working of full wave rectifier using centre tapped transformer.

Last Answer : Full wave Rectifier with Center tapped transformer(FWR): In full wave rectification, the rectifier conducts in both the cycles as two diodes are connected. Circuit diagram: Operation: 1. In ... both half-cycles of input AC voltage. Therefore DC is obtained across the load RL.

When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Last Answer : Feel Free to Answer

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to

Description :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Last Answer :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V 

Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Description : Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Last Answer : Explanation: A centre- tap full wave rectifier drive produces the rectified voltage and it drives the LC filter. We know that the series inductor filter is preferred for low values of load resistance ( ... load RL. The output voltage waveforms are similar to that as shown in figure above.  

If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Description : If the output of a half-wave rectifier is 50-volts peak, what is the average voltage

Last Answer : 15.9 volts.

The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc

Description : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be • 12.1 volt • 1.21 volt • 0.482 volt • 4.82 volt

Last Answer : The ripple voltage in the output of a single phase half wave rectifier with 10 V rectified dc voltage with resistive load and without filter will be 12.1 volt

What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Description : What is the average voltage (Eavg) Output of a full-wave rectifier with an output of 100 volts peak?

Last Answer : 63.7 volts.

What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Description : What is the average voltage (Eavg) output of a full-wave rectifier that has an output of 100 volts peak?

Last Answer : 63.6 volts.

If a half-wave rectifier is added to a half-wave voltage doubler, the resulting circuit is a voltage ___

Description : If a half-wave rectifier is added to a half-wave voltage doubler, the resulting circuit is a voltage ___

Last Answer : Trippler.

Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Description : Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Last Answer : (i) Ripple Factor - Ripple factor (γ) may be defined as the ratio of the root mean square (rms) value of the ripple voltage to the absolute value of the DC component of the ... the same rectifier. Effective VA Rating of transformer is the average of primary and secondary VA rating of transformer.

Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Description : Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Last Answer : Circuit Diagram:    

Describe working of A.C. voltmeter using half wave rectifier with neat circuit diagram.

Description : Describe working of A.C. voltmeter using half wave rectifier with neat circuit diagram. 

Last Answer : AC Voltmeter using Half Wave Rectifier : The a.c. voltmeter using half wave rectifier is achieved by introducing a diode in a basic d.c. voltmeter. This is shown in the Fig. 1. The diode D ... can be obtained for a.c. voltmeter as, Where Idc is the full scale deflection current..

In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output?

Description : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

Last Answer : In a half-wave rectifier, if an a.c supply is 60 Hz. Then what is the a.c ripple at output? (A) 30 Hz (B) 60 Hz (C) 20 Hz (D) 15 Hz

Ripple factor for a half wave rectifier is ....

Description : Ripple factor for a half wave rectifier is  a. 1.65 b. 1.45 c. 1 d. 1.21 

Last Answer : Ripple factor for a half wave rectifier is 1.21

What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Description : What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Last Answer : An open diode will result in no output from a half waverectifier, and an open diode will cut the output of a full waverectifier in half.

The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Description : The illustrated device is a _______. EL-0064 A. full wave bridge rectifier B. half wave bridge rectifier C. solid state voltage regulator D. direct current (DC) filter

Last Answer : Answer: A

The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Description : The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Last Answer : Answer: C

The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Description : The correct term for the illustrated circuit is a ________. EL-0063 A. single phase half wave high power rectifier B. three phase half wave rectifier C. three phase full wave rectifier D. a single phase full wave rectifier

Last Answer : Answer: C

In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier

Description : In the illustrated circuit, section II is considered to be a _______. EL-0085 A. full wave rectifier B. half wave rectifier C. quarter wave rectifier D. short wave rectifier

Last Answer : Answer: A

An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak

Description : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

Last Answer : An SSB transmitter produces a peak-to-peak voltage of 200 V across a 100 Ω antenna load. What is the Peak Envelope Power? A) 49.98 W B) 79.98 W C) 99.96 W D) 199.93 W

What is the equation for determining average voltage in a half-wave rectifier?

Description : What is the equation for determining average voltage in a half-wave rectifier?

Last Answer : Eavg = 0.318 × Emax

In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is

Description : In a 3-phase half-wave rectifier, if per phase input is 200 V, then the average output voltage is   (a) 233.91 V (b) 116.95V (c) 202.56 V (d) 101.28V 

Last Answer : a

A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load...

Description : A single phase, half-wave, controlled rectifier has 400 sin (314 t) as the input voltage and R as the load. For a firing angle of 60° for the SCR, the average output voltage is   (a) 240/π (b) 400/π (c) 300/π (d) 200/π 

Last Answer : C

Section II of the circuit shown in the illustration is the ____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Description : Section II of the circuit shown in the illustration is the ____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: C

Section IV of the circuit shown in the illustration is the _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Description : Section IV of the circuit shown in the illustration is the _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: A

Section III of the circuit shown in the illustration is a _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Description : Section III of the circuit shown in the illustration is a _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: B

In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is:

Description : In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: (1) 50 Hz (2) 100 Hz (3) 150 Hz (4) 200 Hz

Last Answer : In a full wave rectifier with input frequency of 50 Hz, the frequency of the output is: 100 Hz

Rectification efficiency of a full wave rectifier without filter is nearly equals to:

Description : Rectification efficiency of a full wave rectifier without filter is nearly equals to:  (1) 51% (2) 61% (3) 71% (4) 81%

Last Answer : Rectification efficiency of a fullwave rectifier without filter is nearly equals to: 81%

Full wave centre tap rectifier?

Description : Full wave centre tap rectifier?

Last Answer : In this method only two diodes are used. But it requires a center tap transformer. During the positive half cycle diode D1 conducts. In the negative half cycle diode D2 conducts. So in ... rectification converts both polarities of the input waveform to DC (direct current), and is more efficient.

The transformer utilization factor of full wave bridge rectifier is

Description : The transformer utilization factor of full wave bridge rectifier is   (A) 0.812 (B) 0.286 (C) 0.693 (D) 0.782

Last Answer : The transformer utilization factor of full wave bridge rectifier is 0.286 

A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Description : A load with an impedance of 440 ohms is connected across the secondary of the transformer illustrated. If the input voltage is 110 VAC and the step-up ratio is 10 to 1, what will be the primary current? EL-0055 A. 2.5 amps B. 25 amps C. 250 amps D. current cannot be determined with information given

Last Answer : Answer: B

What causes a voltage to be developed across the secondary winding of a transformer?

Description : What causes a voltage to be developed across the secondary winding of a transformer?

Last Answer : The magnetic lines generated by the current in the primary cut

During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Description : During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Last Answer : C) the voltage applied on primary side is low

During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Description : During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Last Answer : C) the voltage applied on primary side is low

One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Description : A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Last Answer : Answer: B

Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is one-half the input frequency. C. The output frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Description : Which of the following expresses the relationship of the input and output frequencies in a full wave rectifier? A. The output frequency is the same as input frequency. B. The output frequency is ... frequency is twice the input frequency. D. The output frequency is four times the input frequency.

Last Answer : Answer: C

Difference between half wave and full wave rectifier?

Description : Difference between half wave and full wave rectifier?

Last Answer : A10: The efficiency of half wave rectifier is not so good as that of full wave rectifier Because only one half of the input waveform reaches the output, it is very inefficient if used for ... reduced in the full-wave rectifier and being reduced further with the increase in the number of phases.

Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Description : Is a full-wave rectifier output easier to filter than that of a half-wave rectifier?

Last Answer : Yes.

Compare half wave rectifier and full wave rectifier.

Description : Compare half wave rectifier and full wave rectifier. 

Last Answer : half wave rectifier and full wave rectifier :

The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Description : The output from a full wave rectifier is (a) A pulsating uni-directional current (b) A DC voltage (c) Zero (d) An AC voltage

Last Answer : a) A pulsating uni-directional current

The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Description : The use of four diodes, in a full-wave bridge rectifier circuit, will __________. A. provide unidirectional current to the load B. allow a very high leakage current from the load C. convert direct current to alternating current D. offer high opposition to current in two directions

Last Answer : Answer: A

Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms.

Description : Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms. 

Last Answer : During the first half cycle : During the first half cycle of the input voltage, the upper end of the transformer secondary winding is positive with respect to the lower end. Thus during the first ... , terminal D, diode D4, and terminal A back to transformer and output will positive half cycle.

Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Description : Draw the circuit diagram of shunt capacitor filter along with full wave rectifier. Draw the waveform of full wave rectifier output and shunt capacitor filter output.

Last Answer : Fig: Shunt capacitor filter along with full wave rectifier Fig: Waveform of full wave rectifier output and shunt capacitor filter output.

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Description : Explain full wave bridged rectifier with the help of circuit diagram and input output waveform.

Last Answer : 1. In positive half cycle (0 to Π): The end A of the secondary winding becomes positive and end B negative. This makes diode D1 and D4 forward biased while diode D2 and D3 are reverse biased. These two diodes will ... D2 and D3 when it is conducting is as follows.  B - D2 - RL - D3 - A 

In a full wave rectifier the negative point in a circuit is

Description : In a full wave rectifier the negative point in a circuit is   (A) cathode (B) anode (C) The central tap on the high voltage secondary (D) plate.

Last Answer : In a full wave rectifier the negative point in a circuit is The central tap on the high voltage secondary