# in short circuit test of transformer which side is short circuited?

164 views

Low voltage side is short circuited.

## Related Questions

Last Answer : Primary is high voltage side and Secondary is low Voltage side.

Explain the procedure to perform Short Circuit test on single phase transformer with circuit diagram.

Last Answer : In short circuit test of transformer the low voltage side is short circuited . On high voltage side the voltmeter is connected in parallel and ammeter in series and also a wattmeter is ... circuit test is done for determining impedance and losses. In this test iron losses is neglected.

Last Answer : High Voltage side is open circuited.

Last Answer : Short circuit test on transformers is conducted to determine copper losses.

Last Answer : The short circuit in any winding of the transformer is the result of impulse voltage.

Last Answer : Primary side is low voltage side and secondary side is high voltage side.

During open circuit test of a transformer?
Last Answer : During open circuit test of a transformer primary is supplied rated voltage.

Describe the difference between an open circuit and a short circuit.
Last Answer : Open circuit means the wire is cut meaning power will not flow and close circuit means wire is not cut and hence power will flow.Short circuit is the same as close circuit

If the % reactance upto the fault point is 20%, then the short circuit current will be
Last Answer : If the % reactance upto the fault point is 20%, then the short circuit current will be 5 times the full load current

The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole)  (A) has q -axis current only (B) has d -axis current only (C) has both d and q axis currents (D) cannot be divided between q and d axis currents
Last Answer : The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole) has d -axis current only

Which of the following are known as the short circuit parameters of a 2- port network? (A) Z- parameters. (B) H- parameters. (C) Y- parameters. (D) A,B,C,D, parameters.
Last Answer : Which of the following are known as the short circuit parameters of a 2- port network? (A) Z- parameters. (B) H- parameters. (C) Y- parameters. (D) A,B,C,D, parameters.

In which fault the maximum short circuit current occurs?
Last Answer : In three phase bolted fault the maximum short circuit occurs.

What can cause a short circuit?

An open-circuit test on a transformer is conducted primarily to measure?
Last Answer : The open-circuit test in a transformer is used to measure

66 While conducting short-circuit test on a transformer the following side is short circuited A. High voltage side B. low voltage side C. primary side D. secondary side
Last Answer : B. Low voltage side

30 In performing the short circuit test of a transformer A. high voltage is usually short circuited B. low voltage side is usually short circuited C. any side is short circuited with preference D. none of the above
Last Answer : B. Low voltage side is usually short circuited

Last Answer : Armature coil is short circuited by brushes when it lies along neutral axis.

Polarity Test of Transformer
Last Answer : Polarity Test of Transformer

Explain the open delta (delta-delta) test on transformer.

If a 5-bus test system contains 6 transmission lines and one transformer, how many non-zero elements are there in the system Y-bus ? (A) 25 (B) 12 (C) 11 (D) 19
Last Answer : If a 5-bus test system contains 6 transmission lines and one transformer, 19 non-zero elements are there in the system Y-bus.

A no-load test is performed on a transformer to determine?
Last Answer : A no-load test is performed on a transformer to determine magnetizing current and loss.

Sumpner's test is conducted on transformer to determine?
Last Answer : Sumpner's test is conducted on transformer to determine temprature.

Equivalent circuit of transformer
Last Answer : Equivalent Circuit Diagram of Transformer Referred to Primary: V1 -Primary Input voltage I1 - Input Current I0- Exciting current/ No load current Im- Magnetizing component ... equivalent of secondary terminal voltage ZL- Load impedance ZL ′- Primary equivalent of load impedance

An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V
Last Answer :  An AC supply of 230 V is applied to a half-wave rectifier circuit through a transformer having primary to secondary turn’s ratio 12:1. The peak inverse voltage is A) 8.62 V B) 12 V C) 19.17 V D) 27.11 V

The secondary of a current transformer is always short-circuited under operating conditions because it?
Last Answer : The secondary of a current transformer is always short-circuited under operating conditions because it avoids core saturation and high voltage induction.

For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is
Last Answer : For a short transmission line with r/x ratio of is 1.0, the regulation will be zero when the load power factor is 0.707 lead

what is mean by short transmission line ?
Last Answer : The transmission lines which have length less than 80 km is known as short transmission lines.

During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer
Last Answer : C) the voltage applied on primary side is low

During short circuit test iron losses are negligible because A. The current on secondary side is negligible B. The voltage on secondary side does not vary C. The voltage applied on primary side is low D. Full-load current is not supplied to the transformer
Last Answer : C) the voltage applied on primary side is low

7 The main advantage of auto transformer over a two winding transformer is A. Hysteresis losses are reduced B. Saving in winding material C. Copper losses are negligible D. Eddy losses are totally ... voltage applied on primary side is low D. Full-load current is not supplied to the transformer

Please, recommend me some extremely neat and short hair cuts for men!
Last Answer : It would be helpful if you include details about the texture of your hair and the shape of your face. Do you have facial hair? Are there any styles that you like?

How to Write a Short Autobiography ?
Last Answer : How to Write a Short Autobiography You may be asked to write a short autobiography every now and then, whether it's for a school assignment, a job application, or a contest you want to join. ... Writing an autobiography does not have to take you too long, provided you have these tips in mind.

State the effects of low power factor on efficiency and voltage regulation of short transmission lines.
Last Answer : i) Effect of Low power factor on efficiency:- When power factor of load reduces current drawn by transmission line increases so copper losses in transmission line increases, hence transmission ... increases, so voltage drop in transmission line increases so regulation increases. (Become Poor)

State advantages of short pitch winding over full pitch winding in alternators.
Last Answer : Advantages of Short Pitch Winding over Full Pitch Winding in Alternators: 1) Short pitching reduces the amount of copper needed for end connection when compared with full pitched coil. 2) They ... reduced, thereby increasing the efficiency. 4) The power quality of generated emf is improved.

3X3 inverse of matrix short trick
Last Answer : 3X3 inverse of matrix short trick

Last Answer : Reactance relay is preferred for phase fault on short transmission line.

When secondary of a current transformer is open-circuited its iron core will be?
Last Answer : When secondary of a current transformer is open-circuited its iron core will be hot because of heavy iron losses taking place in it due to high flux density.

Last Answer : The duration of sudden short-circuit test on a synchronous motor is usually about one second.

64)During the short-circuit test on a small transformer the frequency is increased from 50-200Hz. The copper losses will increase by a factor of A. 16 B. 4 C. 1 D. 1/4

[53] The iron loss of the transformer is negligible during short circuit test because A. The entire input is just sufficient to meet Cu losses only B. Flux produced is a small fraction of the normal flux C. Iron core becomes fully saturated D. Supply frequency is held constant
Last Answer : B. Flux produced is a small fraction of the normal flux

With the help of neat diagram, describe the procedure to carry out phasing out test on a 3 phase transformer. Also state the purpose of conducting this test on 3 phase transformer.
Last Answer : i) This test is carried out on 3-ph transformer to identify primary & secondary winding belonging to the same phase. ii) As shown in fig above all primary & secondary phases ... of this test is to check the respective phases of primary & secondary windings in 3-ph transformer

Why phasing out and polarity test is carried out on three phase transformer?
Last Answer : The phasing out test is carried out to identify the windings (primary and secondary) of corresponding phase of the three phase transformer. The polarity test is carried out to identify the ... identical polarity of the primary and secondary windings of each phase of the three phase transformer.

Explain about the open and short circuit tests on transformer?
Last Answer : A. Open circuit test (No load test) and short circuit test (full load test) are performed on a transformer to determine (i) Equivalent circuit of transformer (ii) Voltage ... determine copper loss in transformer at full load and parameters of approximate equivalent circuit of transformer.

Why SC test is generally performed on HV side of a transformer?
Last Answer : The rated current is less on HV side. This will also permit to use ammeter and wattmeter of lower current range.

Why OC test is generally performed on LV side of a transformer?
Last Answer : The high-voltage side is generally kept open because the current in high-voltage winding is less compared to that on low-voltage winding.The LV side has higher current so that maximum no load current can be measured.

Why the open circuit test on a transformer is conducted at rated voltage?
Last Answer : A:The open circuit on a transformer is conducted at a rated voltage because core loss depends upon the voltage. This open circuit test gives only core loss or iron loss of the transformer.

49 The open circuit test is carried out in a transformer to find the A. Cu loss B. Core loss C. Total loss D. Insulation resistance
Last Answer : B. Core loss

Last Answer : yes High Voltage side of Transformer winding have more number of turns. and low voltage side of Transformer winding have less number of turns.