If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be _____.

 If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be _____.
by

1 Answer

Answer :

 If the range of an analog transducer is 0 to 10 V, then for a resolution of 5 mV, the bits of ADC will be 11.

by

Related questions

Following transducer is an active transducer:

Description : Following transducer is an active transducer: (1) Carbon Microphone (2) Piezoelectric Microphone (3) LVDT (4) Strain Gauge 

Last Answer : Following transducer is an active transducer: Piezoelectric Microphone

Which one of the following is not a transducer in the true sense? (A) Thermocouple (B) Piezoelectric pick-up

Description : Which one of the following is not a transducer in the true sense?   (A) Thermocouple (B) Piezoelectric pick-up (C) Photo voltaic cell (D) LCD.

Last Answer : Which one of the following is not a transducer in the true sense?   (A) Thermocouple (B) Piezoelectric pick-up (C) Photo voltaic cell (D) LCD.

What is a transducer and how does it work?

Description : What is a transducer and how does it work?

Last Answer : An electronic device that converts one form of energy to another form.for example a transducer is used in microphone to convert speech signals to electrical signal.on the other hand,transducer is used to convert an electrical signal to speech signals in speakers.

What is an Analog-to-Digital Converter (ADC) in Arduino?

Description : What is an Analog-to-Digital Converter (ADC) in Arduino?

Last Answer : An Analog-to-Digital Converter (ADC) in Arduino is a component that converts analog signals, such as temperature or light, into digital signals that can be processed by the microcontroller.

An eight bit digital data 10101100 is fed to an ADC. The reference voltage is +10V. The analog output voltage ...

Description : An eight bit digital data 10101100 is fed to an ADC. The reference voltage is +10V. The analog output voltage will be:  (1) 1.05V (2) 6.74V (3) 10.10V (4) 5.15V

Last Answer : An eight bit digital data 10101100 is fed to an ADC. The reference voltage is +10V. The analog output voltage will be: 6.74V.

What is Analog to Digital Converter (ADC) ?

Description : What is Analog to Digital Converter (ADC) ?

Last Answer : Analog to Digital Converter (ADC)  Analog quantity may be voltage, temperature, sound, speed, audio etc. it is information or signal. ... digital form), digital speedometer (converts analog speed into digital form) etc.

Resolution of ADC is defined as a) 1/ (2N – 1) b) 2N-1 c) 1/ (2N-1) d) 2N-1

Description : Resolution of ADC is defined as a) 1/ (2N – 1) b) 2N-1 c) 1/ (2N-1) d) 2N-1

Last Answer : b) 2N-1

Which type of ADC gives high resolution?

Description : Which type of ADC gives high resolution?

Last Answer : Sigma Delta, successive approximation and integrating type analogue to digital converter gives very high resolution but they have slower speed.

The potential difference across the gap of a spark plug ranges between a) 10-20 mV b) 10-20 V c) 10-20 kV d) 10-20 MV

Description : The potential difference across the gap of a spark plug ranges between a) 10-20 mV b) 10-20 V c) 10-20 kV d) 10-20 MV

Last Answer : ans a

Before filling a class V abrasion cavity with GIC you should(+adc March07) A. Clean with pumice, rubber cup, water and weak acid B. Dry the cavity thoroughly before doing anything C. Acid itch cavity then dry thoroughly

Description : Before filling a class V abrasion cavity with GIC you should(+adc March07) A. Clean with pumice, rubber cup, water and weak acid B. Dry the cavity thoroughly before doing anything C. Acid itch cavity then dry thoroughly

Last Answer : A. Clean with pumice, rubber cup, water and weak acid

Potentiometer wire of length `1 m` is connected in series with `490 Omega` resistance and `2 V` battery. If `0.2 mV/cm` is the potential gradient, the

Description : Potentiometer wire of length `1 m` is connected in series with `490 Omega` resistance and `2 V` battery. If `0.2 mV/cm` is the potential gradient, the

Last Answer : Potentiometer wire of length `1 m` is connected in series with `490 Omega` resistance and `2 V` battery. If ... 7.9Omega` C. `5.9Omega` D. `6.9Omega`

Define Analog Transducer and give examples of it

Description : Define Analog Transducer and give examples of it

Last Answer : Analog Transducer: An analog transducer is a device that converts the input signal into a continuous DC signal of voltage or current. Examples: * Strain gauge * L.V.D.T * Thermocouple * Thermistor

An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then baud rate and bit rate of the signal are ............... and .............. (A) 4000 bauds \ sec & 1000 bps (B) 2000 bauds \ sec & 1000 bps (C) 1000 bauds \ sec & 500 bps (D) 1000 bauds \ sec & 4000 bps

Description : An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then baud rate and bit rate of the signal are ............... and .............. (A) 4000 bauds \ sec & ... (B) 2000 bauds \ sec & 1000 bps (C) 1000 bauds \ sec & 500 bps (D) 1000 bauds \ sec & 4000 bps

Last Answer : (D) 1000 bauds \ sec & 4000 bps Explanation: Bit rate is the number of bits per second. Baud rate is the number of signal units per second. Baud rate is less than or equal to the bit rate. Baud rate = 1000 bauds per second (baud/s) Bit rate = 1000 x 4 = 4000 bps

if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Description : if noise voltage =120 mv and signal voltage = 80 v , S/N ratio in dB is?

Last Answer : Answers is the place to go to get the answers you need and to ask the questions you want

A particle of mass m is moving along a straight path through the origin of coordinates with a velocity v. The angular momentum of the particle about the origin (a) mv (b) Depends on its distance from origin (c) Is zero (d) Changes from positive to negative as it passes through the origin

Description : A particle of mass m is moving along a straight path through the origin of coordinates with a velocity v. The angular momentum of the particle about the origin (a) mv (b) Depends on its distance from origin (c) Is zero (d) Changes from positive to negative as it passes through the origin

Last Answer : Ans:(c)

who coined the term micro program in 1951. a. T.V. Wilkes b. MV. Wilkes c. S.V. Wilkes d. DV. Wilkes

Description : who coined the term micro program in 1951. a. T.V. Wilkes b. MV. Wilkes c. S.V. Wilkes d. DV. Wilkes

Last Answer : b. MV. Wilkes

For amplitude measurements, ___ scale is calibrated in either volts per centimeter (V/cm), or millivolts per centimeter (mV/cm)

Description : For amplitude measurements, ___ scale is calibrated in either volts per centimeter (V/cm), or millivolts per centimeter (mV/cm)

Last Answer : vertical

_____ signals can have an infinite number of values ina range. A) Analog B) Digital C) (a) or (b) D) None of the above

Description : _____ signals can have an infinite number of values ina range. A) Analog B) Digital C) (a) or (b) D) None of the above

Last Answer : Analog

An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements are carried by each signal element ? (A) 0.336 bits/baud (B) 3 bits/baud (C) 120,00,000 bits/baud (D) None of the above

Description : An analog signal has a bit rate of 6000 bps and a baud rate of 2000 baud. How many data elements are carried by each signal element ? (A) 0.336 bits/baud (B) 3 bits/baud (C) 120,00,000 bits/baud (D) None of the above

Last Answer : (B) 3 bits/baud

Full scale Ammeter reading is 10 mA, Voltage across Ammeter is 100 mV. Then for 100 A measurements the power loss in the circuit is a) 1 W b) 10 W c) 100 W d) 1000 W

Description : Full scale Ammeter reading is 10 mA, Voltage across Ammeter is 100 mV. Then for 100 A measurements the power loss in the circuit is a) 1 W b) 10 W c) 100 W d) 1000 W

Last Answer : Ans: 10 W*

Bits can be sent over guided and unguided media as analog signal by ___________ a. digital modulation b. amplitude modulation c. frequency modulation d. phase modulation

Description : Bits can be sent over guided and unguided media as analog signal by ___________ a. digital modulation b. amplitude modulation c. frequency modulation d. phase modulation

Last Answer : a. digital modulation

A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.

Description : A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.

Last Answer : (A) N precision resistors.

Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it is assumed that each sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Description : Suppose a digitized voice channel is made by digitizing 8 kHz bandwidth analog voice signal. It is required to sample the signal at twice the highest frequency (two samples per hertz). What is the bit rate required, if it ... sample requires 8 bits? (A) 32 kbps (B) 64 kbps (C) 128 kbps (D) 256 kbps

Last Answer : (C) 128 kbps

Compare analog instrument to digital instrument on the basis of accuracy, resolution, power required and portability.

Description : Compare analog instrument to digital instrument on the basis of accuracy, resolution, power required and portability. 

Last Answer : Comparison between Analog instruments & Digital instruments: 

What is the temperature sensor?

Description : What is the temperature sensor?

Last Answer : Temperature sensor is a device usually Resistance Temperature Detector (RTD) or Thermocouple that provides for temperature measurement through electrical signal.

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Description : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Last Answer : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a ... `) A. 1 B. 2 C. 5 D. 10

A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Description : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Last Answer : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a ... `) A. 1 B. 2 C. 5 D. 10

With regard to pattern electroretinogram: a. it can be used to estimate the visual acuity b. it is generated by the occipital cortex c. it is reduced in optic nerve diseases d. the signal amplitude is about 10 mV

Description : With regard to pattern electroretinogram: a. it can be used to estimate the visual acuity b. it is generated by the occipital cortex c. it is reduced in optic nerve diseases d. the signal amplitude is about 10 mV

Last Answer : it is reduced in optic nerve diseases

Why most of analog o/p devices having o/p range 4 to 20 mA and not 0 to 20 mA?

Description : Why most of analog o/p devices having o/p range 4 to 20 mA and not 0 to 20 mA?

Last Answer : 4-20 mA is a standard range used to indicate measured values for any process. The reason that 4ma is chosen instead of 0 mA is for fail safe operation.  For example: A pressure instrument gives output 4mA ... is 0-20 mA then we can differentiate whether it is due to broken wire or due to 0 psi.

In Go-Back-N ARQ, if 5 is the number of bits for thesequencenumber, then the maximum size of the receive window mustbe _____ A) 15 B) 16 C) 31 D) 1

Description : In Go-Back-N ARQ, if 5 is the number of bits for thesequencenumber, then the maximum size of the receive window mustbe _____ A) 15 B) 16 C) 31 D) 1

Last Answer : 1

In Go-Back-N ARQ, if 5 is the number of bits for thesequencenumber, then the maximum size of the send window must be _____ A) 15 B) 16 C) 31 D) 1

Description : In Go-Back-N ARQ, if 5 is the number of bits for thesequencenumber, then the maximum size of the send window must be _____ A) 15 B) 16 C) 31 D) 1

Last Answer : 31

In the above figure, O is the centre of the circle AB,AD and CD are the chords . If `/_ ADC=130^(@)` then fid `/_ ACB`.

Description : In the above figure, O is the centre of the circle AB,AD and CD are the chords . If `/_ ADC=130^(@)` then fid `/_ ACB`.

Last Answer : In the above figure, O is the centre of the circle AB,AD and CD are the chords . If `/_ ADC=130^(@)` then fid `/_ ACB`.

How many grams of KI are in 25.0ml of a 3.0 (mv) KI solution?

Description : How many grams of KI are in 25.0ml of a 3.0 (mv) KI solution?

Last Answer : The solution contain 12,47 g KI.

At rest, the interior of the typical mammalian neuronal axon potential is approximately ________ mV (a) 0 (b) –70 (c) –100 (d) –20

Description : At rest, the interior of the typical mammalian neuronal axon potential is approximately ________ mV (a) 0 (b) –70 (c) –100 (d) –20

Last Answer : Ans: B

Let C be a binary linear code with minimum distance 2t + 1 then it can correct upto _____ bits of error. a. t + 1 b. t c. t - 2 d. t / 2

Description : Let C be a binary linear code with minimum distance 2t + 1 then it can correct upto _____ bits of error. a. t + 1 b. t c. t - 2 d. t / 2

Last Answer : b. t

What is the minimum number of bits required in a PCM code for a range of 10,000? A. 12 B. 9 C. 14 D. 10

Description : What is the minimum number of bits required in a PCM code for a range of 10,000? A. 12 B. 9 C. 14 D. 10

Last Answer : C. 14

A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale...

Description : A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is

Last Answer : A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is 2.5 milliOhm

Which of the listed statements is correct when using an analog multimeter as an ohmmeter? A. The pointer should be adjusted to zero each time a new resistance range is selected. B. The pointer will move to infinity when the meter is not in use. C. Ohmmeters are not sufficiently sized to measure conductor insulation resistance. D. All of the above.

Description : Which of the listed statements is correct when using an analog multimeter as an ohmmeter? A. The pointer should be adjusted to zero each time a new resistance range is selected. B. The ... C. Ohmmeters are not sufficiently sized to measure conductor insulation resistance. D. All of the above.

Last Answer : Answer: D

Explain range extension for analog DC voltmeter.

Description : Explain range extension for analog DC voltmeter.

Last Answer : Explanation A DC voltmeter can be converted into a multirange voltmeter by connecting a number of resistors (multipliers) in series with the meter movement 

On what date did MV Swat reach Chittagong ?

Last Answer : MV Swat reached Chittagong on 3rd March 1971.

De Broglie equation is (a) h/mv = 1 (b) E1 – E2 = hv (c) C = 1v (d) n1 = 2d sin q

Description : De Broglie equation is (a) h/mv = 1 (b) E1 – E2 = hv (c) C = 1v (d) n1 = 2d sin q

Last Answer : Ans:(a)

The de Broglie equation is (a) h/mv = 1 (b) hv = E2 - E1 (c) n 1 = 2d sin (d) c = hv

Description : The de Broglie equation is (a) h/mv = 1 (b) hv = E2 - E1 (c) n 1 = 2d sin (d) c = hv

Last Answer : Ans:(a)

At 17˚ C, the noise voltage generated by 5kΩ resistor, operating over a bandwidth of 20KHz is A. 1.3 nV B. 1.3 µV C. 1.3 pV D. 1.3 mV

Description : At 17˚ C, the noise voltage generated by 5kΩ resistor, operating over a bandwidth of 20KHz is A. 1.3 nV B. 1.3 µV C. 1.3 pV D. 1.3 mV

Last Answer : B. 1.3 µV

An emf of the order of mV is generated when two solutions of different hydrogen ion concentration are separated by a thin glass wall". This is the working principle of a (A) pH meter (B) Polarimeter (C) Chromatograph (D) Polarograph

Description : An emf of the order of mV is generated when two solutions of different hydrogen ion concentration are separated by a thin glass wall". This is the working principle of a (A) pH meter (B) Polarimeter (C) Chromatograph (D) Polarograph

Last Answer : (A) pH meter

According to the equation ‘r = (mv)⁄(Be)’, the faster moving particles A. move in smaller circle B. move straight C. move in bigger circle D. move randomly

Description : According to the equation ‘r = (mv)⁄(Be)’, the faster moving particles A. move in smaller circle B. move straight C. move in bigger circle D. move randomly

Last Answer : move in bigger circle

In most nerve and muscle cell, the membrane potentical is a. 60 mv b. 70 mv c. 85 mv d. 100 mv

Description : In most nerve and muscle cell, the membrane potentical is a. 60 mv b. 70 mv c. 85 mv d. 100 mv

Last Answer : 85 mv

Which command is used to remove a file? A. remove B. rm C. mv D. del E. None of the above

Description : Which command is used to remove a file? A. remove B. rm C. mv D. del E. None of the above

Last Answer : B. rm

A proton having mass m and charge q is projected into a region having a perpendicular magnetic field. The angle of deviation of proton when it comes out of the region with mv √2 qB ⁄ is a) π/3 b) π/4 c) π/6 d) 2 π/3

Description : A proton having mass m and charge q is projected into a region having a perpendicular magnetic field. The angle of deviation of proton when it comes out of the region with mv √2 qB ⁄ is a) π/3 b) π/4 c) π/6 d) 2 π/3

Last Answer : b) π/4

The mv command changes (A) the inode (B) the inode-number (C) the directory entry (D) both the directory entry and the inode

Description : The mv command changes (A) the inode (B) the inode-number (C) the directory entry (D) both the directory entry and the inode

Last Answer : (C) the directory entry