A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is A) Manganin wire of 20 m Ω B) Constantan wire of 20 m Ω C) Manganin wire of 25 m Ω D) Constantan wire of 25 m Ω

1 Answer

Answer :

A 10A DC Ammeter has a resistance of 0.1 Ω is to be extended to 50 A, the required shunt wire is Manganin wire of 25 m Ω

Related questions

Description : A DC ammeter has resistance `0.1 Omega` and its current ranges `0-100 A`. If the range is to be extended to `0-500`, then the following shunt resistan

Last Answer : A DC ammeter has resistance `0.1 Omega` and its current ranges `0-100 A`. If the range is to be extended ... Omega` C. `0.025 Omega` D. `0.25 Omega`

Description : A galvanometer of 65 Ω resistance gives full scale deflection with 4 mA current. In order to convert it into ammeter, the range of 10 A is connected with it, the shunt resistance should be a) 0.1 Ω b) 0.2 Ω c) 0.06 Ω d) 0.03 Ω

Last Answer : d) 0.03 Ω

Description : Sketch the circuit of basic DC ammeter , derive equation for shunt resistance.

Last Answer : Derivation The basic movement of dc ammeter circuit consists of D' Arsonval galvanometer. When large current is to be measured then some extra modification is required. For measurement of large current by using ... same. Vsh =Vm m IshRsh=ImRm Rsh=ImRm/Ish Rsh=ImRm/(I-Im) 

Description : Calculate the resistance of shunt required to make a milliammeter which gives maximum deflection for a current of 15 mA and which has a resistance of 5 Ω; read up to 10 Amp.

Last Answer : Answer :

Last Answer : The function of shunt in an ammeter is to by pass the current.

Description : Assertion : Resistance of an ammeter is less than the resistance of a milliammeter. Reason : Value of shunt required in case of ammeter is more than a

Last Answer : Assertion : Resistance of an ammeter is less than the resistance of a milliammeter. Reason : Value of ... . If Assertion is false but Reason is true.

Description : Ideal resistance of ammeter is A. 1 Ω B. 2 Ω C. 0 Ω D. infinite

Last Answer : 0 Ω

Description : The shunt of a DC ammeter should be connected in __________. A. series with the load and in parallel with the meter movement B. parallel with the load and in series with the meter movement C. ... and in parallel with the meter movement D. series with the load and in series with the meter movement

Last Answer : Answer: A

Description : Draw and state how Aryton shunt type DC ammeter . State advantage of using Aryton shunt.

Last Answer : OR The Aryton shunt eliminates the possibility of having the meter in the circuit without a shunt. This advantage is gained at the price of slightly higher overall Aryton shunt ammeter. In this ... between shunts. 3. Another advantage is that it may be used as a wide range ammeter. 

Description : A moving coil galvanometer is converted into an ammeter reads upto `0.03 A` by connecting a shunt of resistance `4r` across it and ammeter reads up `0

Last Answer : A moving coil galvanometer is converted into an ammeter reads upto `0.03 A` by connecting a shunt of resistance `4r` ... `0.02A` C. `0.03A` D. `0.04A`

Description : A galvanometer has resistance of 120 Ω. In order to pass 5% of the main current in it, the value of shunt resistance Rs must be equal to a) 6.3 Ω b) 6 Ω c) 2 Ω d) 2.3 Ω

Last Answer : a) 6.3 Ω

Last Answer :  If a DC voltmeter is made from an ammeter having a fed of 100μA then its sensitivity (in KΩ/V) will be 10.

Description : Hot wire ammeter is used (a) only for dc circuit (b) only for ac circuit (c) both (a) and (b) (d) Either (a) or (b) 

Last Answer : Either  a  or   b.

Description : An ammeter has a current change of 0-5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) ... series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

Last Answer : An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of 0.05 ohm in parallel with the meter

Description : A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is (A) 2.5 W (B) 5 W (C) 32.5 W (D) 35 W

Last Answer : A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is 35 W

Description : Calculate the shunt resistance needed to increase the FSD of an ammeter 5 times if the meter resistance is 1kohm

Last Answer : 250ohms

Description : What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Last Answer : D. 75 Ω

Description : What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Last Answer : A. 100Ω

Description : When a resistor is used as a shunt and is connected in parallel with a meter movement coil, it will provide _____________. A. a measurement of circuit resistance B. an increased accuracy of approximately 1.5 percent C. an extended meter range D. none of the above

Last Answer : Answer: C

Description : A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is:

Last Answer : A permanent magnet moving coil ammeter has a coil resistance of 99 ohm and Full Scale Deflection (FSD) current of 0.1mA. Shunt resistance is 1 ohm. Current through the meter at 0.5 F.S.D is: 0.05mA

Last Answer : The internal resistance of the ammeter should ideally be Zero.

Last Answer : The internal resistance of an ammeter should be Very small.

Description : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. What is the value of series resistor to be used?

Last Answer : The full-scale deflection current of an ammeter is 1 mA and its internal resistance is 100Ohm. This is to have full deflection when 100V is measured. 99.99 K ohms is the value of series resistor to be used.

Description : A 1000W heater is rated to operate at a direct current (DC) of 10A. If the heater is supplied alternating current (AC) for producing the same quantity of heat the value of current should be  a. Iav=10A b. Irms=10A c. Ipeak=10A 

Last Answer : A 1000W heater is rated to operate at a direct current (DC) of 10A. If the heater is supplied alternating current (AC) for producing the same quantity of heat the value of current should be Irms=10A

Description : Currents of `10A, 2A` are passed through two parallel wires `A` and `B` respectively in opposite directions. If the wire `A` is infinitely long and th

Last Answer : Currents of `10A, 2A` are passed through two parallel wires `A` and `B` respectively in opposite directions. If the ... `4xx10^(-7)N` D. `8xx10^(-7)N`

Description : Fuse wire protection system is usually not used beyond: a. 10A b. 25A c. 50A d. 100A  

Last Answer : Fuse wire protection system is usually not used beyond: a. 10A b. 25A c. 50A d. 100A  

Last Answer : A moving-coil permanent-magnet instrument can be used as ammeter by using a low resistance shunt.

Description : A transmitted signal 5 meters in wavelength is received by an antenna coil having a 50-Ω resistance and a 0.01 H inductance. What is the capacitance of the tuner shunting the antenna coil at this point? A. 0.704 fF B. 0.704 μF C. 0.704 nF D. 0.704 mF

Last Answer : A. 0.704 fF

Description : Grid cables are 15 km long with a resistance of 0.20 Ω km-1, powers wasted as heat in these cables are A. 50 kW B. 60 kW C. 20 kW D. 30 kW

Last Answer : 30 kW

Description : An ammeter has a full-scale deflection current of 100mA. If the same ammeter is used to measure a full-scale current of 1.0ampere, what is the value of the shunt resistor in ohms if the voltage across the meter is 9.0 volts?

Last Answer : 10 ohms

Description : An internal resistance is placed in series with the meter movement of which of the following instruments? A. AC ammeter B. DC ammeter C. DC voltmeter D. Frequency meter

Last Answer : Answer: C

Description : In order to increase its range of measurement, a resistance would be placed in series with which of the following instruments? A. DC voltmeter B. DC ammeter C. frequency meter D. power factor meter

Last Answer : Answer: A

Description : Which of the listed electrical devices is represented by the symbol shown in the illustration? EL-0055 A. Fixed resistance resistor B. Coil with magnetic core C. DC motor or generator shunt field D. Transformer

Last Answer : Answer: D

Description : To limit the current flow through a DC voltmeter to as low a value as possible, the moving coil circuit is provided with a/an _____________. A. high series resistance B. high parallel resistance C. series inductor D. external shunt

Last Answer : Answer: A

Description : A shunt-fed quarter-wavelength Marconi antenna A. has maximum RF impedance to ground at its feedpoint B. has a current null at its feedpoint C. has a zero DC resistance to ground D. has zero RF resistance to ground

Last Answer : C. has a zero DC resistance to ground

Description : As compared to shunt and compound DC motors, the series DC motor will have the highest torque because of its comparatively ____________ at the start. (A) Lower armature resistance. (B) Stronger series field. (C) Fewer series turns. (D) Larger armature current.

Last Answer : (D) Larger armature current.

Description : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

Last Answer : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is 36 Ohm

Description : Armature shunting method of speed control of dc shunt motor is preferred over annature resistance method due to:  (1) Better speed regulation (2) Less loss in external resistance (3) Simplicity in control circuit (4) Reduced cost of controller

Last Answer : Armature shunting method of speed control of dc shunt motor is preferred over annature resistance method due to: Better speed regulation.

Description : A 0-10 A ammeter has a guaranteed accuracy of 1% of full scale deflection, the limiting error while reading 2.5 A will be (a) 1% (b) 2% (c) 4% (d) None of these 

Last Answer : A

Description : A 50 kW dc shunt is loaded to draw rated armature current at any given speed. When driven  (i) at half the rated speed by armature voltage control and (ii) at 1.5 times the rated speed by field control, the respective output powers ... kW in (i) and 75 kW in (ii) (D) 50 kW in (i) and 50 kW in (ii)

Last Answer : A 50 kW dc shunt is loaded to draw rated armature current at any given speed. When driven  (i) at half the rated speed by armature voltage control and (ii) at 1.5 times the rated speed by field control, the respective output ... kW in (i) and 75 kW in (ii) (D) 50 kW in (i) and 50 kW in (ii)

Description : A receiver connected to an antenna whose resistance is 50 Ω has an equivalent noise resistance of 30Ω. Calculate its equivalent noise temperature if the noise figure is equal to 1.6. A. 17.4 K B. 174K C. 1.74K D. 17K

Last Answer : B. 174K

Description : Three resistances 20 Ω, 30 Ω and 60 Ω are connected in parallel, their combined resistance is given by A. 110 Ω B. 50 Ω C. 20 Ω D. 10 Ω

Last Answer : 10 Ω

Description : Find the current in a conductor with resistance 2 ohm, electric field 2 units and distance 100cm. a) 1A b) 10mA c) 10A d) 100mA

Last Answer : a) 1A

Description : How range of A.C. ammeter & A.C. voltmeter is extended? Draw suitable diagram.

Last Answer : Extension of A.C. Ammeter Range: The range of a.c. ammeter can be extended by using CT, the arrangement is shown in figure. The CT is current transformer having less number of primary turns carrying high ... high magnitude of source voltage. In this way range of a.c. voltmeter can be extended.

Description : What is ammeter shunt ?

Last Answer : A small amount of radial coupling in parallel with the coil to increase the range of ammeter is called ammeter shunt.

Description : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) of necessary shunt will be

Last Answer : A milli voltmeter of 25 milli volt range is to be converted into an ammeter of 25 ampere range. The value (in ohm) ... 001` B. `0.01` C. 1 D. `0.05`

Description : Which of the following meters uses a shunt connected in series with the load, but parallel with the meter movement? A. voltmeter B. power factor meter C. wattmeter D. ammeter

Last Answer : Answer: D

Description : Which of the following statements represents the correct method of connecting the shunt of an ammeter prior to taking a reading? A. In series with the load and in series with the meter movement. B. In ... with the meter movement. D. In parallel with the load and in parallel with the meter movement.

Last Answer : Answer: B

Description : Which of the listed meters uses a shunt connected in series with the load, but parallel with the meter movement? A. Voltmeter B. Power factor meter C. Ammeter D. Wattmeter

Last Answer : Answer: C

Description : The shunt used in an ammeter should be connected in ____________. A. series with the load and in parallel with the meter movement B. parallel with the load and in series with the meter movement C. ... in parallel with the meter movement D. series with the load and in series with the meter movement

Last Answer : Answer: A