An energy signal has G(f) = 20. Its energy density spectrum is

 An energy signal has G(f) = 20. Its energy density spectrum is A) 20 B) 100 C) 400 D) 800  
by

2 Answers

Answer :

 An energy signal has G(f) = 20. Its energy density spectrum is 400 

by

Answer :

400
by

Related questions

Applications of Spectrum Analyser

Description : Applications of Spectrum Analyser

Last Answer : Applications of Spectrum Analyser are as follows: i) It is used to study the RF spectrum produced in microwave instrument. ii) It is used for testing of RF interference. iii) It is used for measurement ... a parametric amplifier. xi) It is used to measure the modulation index of an AM wave.

i) Explain electromagnetic spectrum with neat diagram. ii) Explain atmospheric noise with example.

Description : i) Explain electromagnetic spectrum with neat diagram. ii) Explain atmospheric noise with example. 

Last Answer : Explanation:-  The electromagnetic spectrum is the range of frequencies of electromagnetic radiation and their respective wavelengths  The electromagnetic spectrum covers ... spread over the complete frequency spectrum used for radio communication.  Example: Lightning 

Spectrum analyzer

Description : Spectrum analyzer

Last Answer : Spectrum analyzer Spectrum analyzer is use for measuring signal in frequency domain. It measure modulation, distortion and noise. Spectrum analyzer measure the electrical input signal, for measuring ... of the signal. Other control include dynamic range, sweep speed and resolution bandwidth.

If B is the flux density, I the length of conductor and v the velocity of conductor, then induced e.m.f. is given by?

Last Answer : If B is the flux density, I the length of conductor and v the velocity of conductor, then induced e.m.f. is given by Blv.

If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be

Description :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

Last Answer :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be Distorted 

Define magnetic flux density and state its formula.

Description : Define magnetic flux density and state its formula.

Last Answer : The magnetic flux per unit area is called as magnetic flux density. Magnetic flux density is denoted by B. The formula for magnetic flux density is Weber per metre square or Tesla. Mathematically ... the unit of magnetic flux density is Weber per metre square which is also called as Tesla.

In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will

Description : In an induction motor if the flux density is reduced to one-half, of its normal value then the torque will  (1) reduce to one-half (2) reduce to one-fourth (3) remain unchanged (4) increase four times

Last Answer : In an induction motor if the flux density is reduced.to one-half, of its normal value then the torque will reduce to one-fourth

Flux density formula

Description : Flux density formula

Last Answer : Flux density formula

Define the following terms: i) Magnetic flux density, ii) Reluctance, iii) Magneto-motive force, iv) Permeance.

Description : Define the following terms: i) Magnetic flux density, ii) Reluctance, iii) Magneto-motive force, iv) Permeance.

Last Answer : (i) Magnetic flux density (B): It is the magnetic flux per unit area measured at right angles to the flux path. (Its unit is weber/m2 or tesla).  (ii) Reluctance: It is the ... flux to set up through it and it is reciprocal of reluctance. Permeance = 1/ Reluctance. Unit: weber/ampere.

In lead acid battery the density of acid indicates the

Description : In lead acid battery the density of acid indicates the  (1) charge of the battery (2) level of acid (3) e.m.f of the battery (4) damage of the plates

Last Answer : In lead acid battery the density of acid indicates the charge of the battery

What is the permissible flux density in case of cold rolled grained oriented steel?

Description : What is the permissible flux density in case of cold rolled grained oriented steel?

Last Answer : The permissible flux density in case of cold rolled grained oriented steel is 1.7 Wb/m2.

what is the unit of flux density?

Last Answer : Flux density is denoted by B. And it is given as B = flux/ area Where, the unit of flux is Weber and unit of area is meter square. So the unit of flux density is weber per meter square which is also called as Tesla.

An energy signal has G(f) = 10. Its energy density spectrum is:

Description : An energy signal has G(f) = 10. Its energy density spectrum is:  (1) 10 (2) 100 (3) 50 (4) 20

Last Answer : An energy signal has G(f) = 10. Its energy density spectrum is: 100.

2.The period of a signal is 10ms. What is its frequency in kilohertz?

Description : .2.The period of a signal is 10ms. What is its frequency in kilohertz?

Last Answer : 100

In 8085, whenever a signal is received at TRAP terminal, its program execution is transferred to a subroutine

Description : In 8085, whenever a signal is received at TRAP terminal, its program execution is transferred to a subroutine on address A) 0000 H B) 002C H C) 0024 H D) 0004 H

Last Answer : In 8085, whenever a signal is received at TRAP terminal, its program execution is transferred to a subroutine on address 0024 H

Explain Briefly What Happens When The Intr Signal Goes High In The 8085?

Description : Explain Briefly What Happens When The Intr Signal Goes High In The 8085?

Last Answer : Answer :The INTR is a maskable interrupt for the 8085. It has the lowest priority and is also non vectored. When this INTR signal goes into the high state the following things occur / ... the processor saves the address of new instruction into the STACK and an interrupt service subroutine begins.

State different types of electrical signal and draw all types of waveforms.

Description : State different types of electrical signal and draw all types of waveforms.

Last Answer : Types of electrical signals 1) Sine wave 2) Triangular wave 3) Square wave Waveforms

basic characteristics of sound signal.

Description :  basic characteristics of sound signal.

Last Answer : Level and loudness: The amplitude of a sound wave determines its loudness or volume. A larger amplitude means a louder sound, and a smaller amplitude means a softer sound. The loudness of a ... the reproducing system should be capable of handling the maximum and minimum power in the same ratio. 

What is the significance of signal conditioner? Explain the need of following in mechatronics system. i) Isolator ii) Filter iii) Amplifier iv) Data converter

Description : What is the significance of signal conditioner? Explain the need of following in mechatronics system. i) Isolator ii) Filter iii) Amplifier iv) Data converter

Last Answer : Significance: Signal conditioning means manipulating an analog signal in such a way that it meets the requirements of the next stage for further processing. Signal inputs accepted by signal ... -frequency converters, current-to-voltage converters, current loop converters, and charge converters.  

List different methods of demodulation of FM signal.

Description : List different methods of demodulation of FM signal.

Last Answer : Balanced Slope detection Ratio detector Foster Seeley discriminator Phase locked loop demodulator 

For a signal conditioner explain the terms linearization and signal conversion.

Description : For a signal conditioner explain the terms linearization and signal conversion.

Last Answer : Definition :  1. linearization : Many primary elements produce nonlinear outputs and the signal must be linearized to produce a nearly ideal calibration. Specialized analog circuits such as offsetting circuits, ... signal. Even computer algorithms are also used. 2.Signal conversion :

Analog signal

Description : Analog signal

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is

Description :  If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is the transmitter from the target? A) 150 Km B) 150 m C) 15 Km D) 1500 m 

Last Answer :  If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is the transmitter from the target? A) 150 Km B) 150 m C) 15 Km D) 1500 m 

What is the Laplace transform of step signal of 5 units magnitude?

Description : What is the Laplace transform of step signal of 5 units magnitude?  A) 5s B) 5/s C) s/5 D) 1/s 

Last Answer : What is the Laplace transform of step signal of 5 units magnitude?  A) 5s B) 5/s C) s/5 D) 1/s 

The time base signal in Cathode Ray Oscilloscope (CRO) is

Description : The time base signal in Cathode Ray Oscilloscope (CRO) is  (1) A square wave signal (2) A sawtooth signal (3) A triangular wave signal (4) A sinusoidal signal

Last Answer : 2 Saw tooth 

Integration of step signal gives

Description : Integration of step signal gives (A) Impulse signal. (B) Ramp function. (C) Parabola. (D) Square pulse.

Last Answer : Integration of step signal gives Ramp function.

The standard for long distance analog signal transmission in process control industry is

Description : The standard for long distance analog signal transmission in process control industry is (A) 4-20 mV (B) 0-20 mA (C) 4-20 mA (D) 0-5 V

Last Answer : The standard for long distance analog signal transmission in process control industry is 4-20 mA

What are the advantages of a digital signal?

Description : What are the advantages of a digital signal?

Last Answer : It  has   only   two  variable   input  and  output (low   or    high)   (0  or    5).

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse

Description : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Last Answer : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

A project activity has several components as indicated below; S. No. Activity Preceded by Duration (in Weeks) 1 A - 8 2 B A 6 3 C A 12 4 D B 4 5 E D 5 6 F B 12 7 G E& F 9 8 H C 8 9 I F & H 5 10 J I & G 6 d. Prepare a PERT chart, estimate the duration of the project and identify the critical path.

Description : A project activity has several components as indicated below; S.  No. Activity Preceded by Duration (in  Weeks) 1 A - 8 2 B A 6 3 C A 12 4 D B 4 5 E D 5 6 F B 12 7 G E& F ... H 5 10 J I & G 6 d. Prepare a PERT chart, estimate the duration of the project and identify the  critical path.

Last Answer : PERT Diagram based on Activity on Arrow  .  E  D 5 G B 5 9 J, 6 A 6 F,12 I ,5 8 c 12 H 8 OR  PERT Diagram based on Activity on Node …………………….6 marks a. Critical Path: A-B-F-G-J …………………….1 mark  b. Estimated Project Duration: 41 weeks

Which of the following device is used for coupling microwave energy?

Description : Which of the following device is used for coupling microwave energy?  A) Resonator B) Waveguide C) Loop D) Antenna

Last Answer : A

Phantom loading for testing of energy meter is used

Description : Phantom loading for testing of energy meter is used (A) to isolate the current and potential circuits (B) to increase power loss during testing (C) for meters having low current ratings (D) to test meters having a large current rating for which loads may not be available

Last Answer : B

what is fermi energy

Description : what is fermi energy

Last Answer : Fermi energy is the part of electron band diagram.Fermi energy is highest energy that the electron assume at T = 0 K. Fermi level comes in between conduction band and valance band. In case of ... , In case of semiconductor energy gap is small, And in case of conductor energy gap is overlap.

1 kg of wood contains 15% moisture and 5% hydrogen by weight. How much water is evaporated during complete combustion of 1kg of wood? a) 0.6 kg b) 200 g c) 0.15 kg d) none of the above

Description : 1 kg of wood contains 15% moisture and 5% hydrogen by weight. How much water is evaporated during complete combustion of 1kg of wood? a) 0.6 kg b) 200 g c) 0.15 kg d) none of the above

Last Answer : b)200 g

Assume CO2 equivalent emissions by the use of a 60 W incandescent lamp are of the order of 60 g/hr. If it is replaced by a 5 W LED lamp then the equivalent CO2 emissions will be a) nil b) 5 g/hr c) 12 g/hr d) 300 g/hr

Description : Assume CO2 equivalent emissions by the use of a 60 W incandescent lamp are of the order of 60 g/hr. If it is replaced by a 5 W LED lamp then the equivalent CO2 emissions will be a) nil b) 5 g/hr c) 12 g/hr d) 300 g/hr

Last Answer : b) 5 g/hr

A company has to choose between two projects whose cash flows are as indicated below; Project 1: i. Investment – Rs. 15 Lakhs ii. Annual cost savings – Rs. 4 lakhs. iii. Bi-annual maintenance cost – Rs. 50,000/- iv. Reconditioning and overhaul during 5th year: 6 lakhs v. Life of the project – 8 years vi. Salvage value – Rs. 5 lakhs Project 2: vii. Investment – Rs. 14 Lakhs viii. Annual cost savings – Rs. 3.5 lakhs. ix. Annual Maintenance cost – Rs. 20,000/- x. Reconditioning and overhaul during 4th year: 5 lakhs xi. Life of the project – 8 years xii. Salvage Value- 2 lakhs Which project should the company choose? The annual discount rate is 12

Description :  A company has to choose between two projects whose cash flows are as indicated  below; Project 1:  i. Investment - Rs. 15 Lakhs ii. Annual cost savings - Rs. 4 lakhs. iii. Bi-annual ... years xii. Salvage Value- 2 lakhs Which project should the company choose? The annual discount rate is 12

Last Answer : Year Project 1 Project 2 Outgo Saving NPV Outgo Saving NPV 0 15.0 0 =-15.0 14.0 0 = -14 1 0 4.0 = (4 / (1+.12)1 = 3.571 0.2 3.5 = (3.3 / (1+.12)1 = 2.95 2 0.5 4.0 = (3.5 / (1+.12)2 = 2.79 0.2 3.5 ... (1+.12)8 = 3.43 0.2 5.5  (3.5+2) = (5.3 / (1+.12)8 = 2.14 NPV = + 2.301 @12% = + 0.15

Think back a couple of years, when corn was being touted as a "renewable energy source" and its plentiful supply would solve our energy problems forever. What happened?

Description : Think back a couple of years, when corn was being touted as a "renewable energy source" and its plentiful supply would solve our energy problems forever. What happened?

Last Answer : answer:Biofuels are a good idea in rich countries with surplus production of food. Biofuels are a bad idea in poor countries where people struggle to be able to pay for their food. Using ... farm. And there's also geothermal. Plus energy efficiency. Better windows. Better insulation of buildings.

Is there technology that would allow us to use the Earth’s gravity and it’s force to solve the energy problems?

Description : Is there technology that would allow us to use the Earth’s gravity and it’s force to solve the energy problems?

Last Answer : Dog Are you shitting me? Before 10:00? This is way too profound.

Answer the following S. No Statement Chose the correct answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the blanks 3 Non Contact Infrared Thermometer cannot measure temperature of objects placed in hazardous places True/False 4 To measure the RPM of a Flywheel, ______ type of RPM meter is used and for a visible shaft-end _______ type of RPM meter is used. Fill in the blanks 5 In a switch yard, _____ instrument is used to identify the loose joints and terminations Fill in the blanks 6 Every Designated Consumer shall have its first energy audit conducted by ________ Energy Auditor within ______ months of

Description :  Answer the following S. No Statement Chose the correct  answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the ... of RPM  meter is used and for a visible shaft-end _______ type of  RPM meter is used.

Last Answer : Sr  No Statement Chose the correct  answer OR Fill-in-the-blanks Solution 1 Fyrite measures CO2, O2 and  SO2 True/False False 2 Ultrasonic Flow Meter uses the  principle of____& ____ ... ]  10 In a gasification system the  reduction zone is above the  combustion zone True/False False

A manufacturing industry plans to improve its energy performance under PAT through implementation of an energy conservation scheme. After implementation, calculate the Plant Energy Performance (PEP) with 2015-16 as the reference year. What is your inference? Given that:  The current year (2016-17 ) Annual Production – 28,750 T ,  Current year (2016-17 ) Annual Energy Consumption– 23,834 MWh,  Reference year (2015-16 ) production - 34,000 T,  Reference year (2015-16 ) Energy consumption - 27,200 MWh.

Description : A manufacturing industry plans to improve its energy performance under PAT through  implementation of an energy conservation scheme. After implementation, calculate the  Plant Energy Performance (PEP) with 2015-16 as the ... 34,000 T,   Reference year (2015-16 ) Energy consumption - 27,200 MWh.

Last Answer : Production factor (PF) = 28750/34000 = 0.846 …………………….1 mark Ref year equivalent energy (RYEE) = Ref Year Energy Use (RYEU) x PF   = 27,200 x 0.846= 23011MWh

An electric heater consumes 1000 Joules of energy in 5 seconds. Its power rating is: a) 200 W b) 1000 W c) 5000W d) none of the above

Description : An electric heater consumes 1000 Joules of energy in 5 seconds. Its power rating is: a) 200 W b) 1000 W c) 5000W d) none of the above

Last Answer : a) 200 W

A building intended to be used for commercial purpose will be required to follow Energy conservation building code under Energy Conservation Act, 2001 provided its a) connected load is 120 kW and above b) contract demand is 100 kVA and above c) connected load is100 kW and above or contract demand is 120 kVA and above

Description : A building intended to be used for commercial purpose will be required to follow Energy conservation building code under Energy Conservation Act, 2001 provided its a) connected load is 120 kW and above b) ... and above c) connected load is100 kW and above or contract demand is 120 kVA and above

Last Answer : c) connected load is100 kW and above or contract demand is 120 kVA and above

Explain energy conservation and its importance.

Description : Explain energy conservation and its importance.

Last Answer : Energy conservation Energy Conservation is the deliberate practice or an attempt to save electricity, fuel oil or gas or any other combustible material, to be able to put to additional use for ... are produced. e) Generally to relieve shortage and improve development. f) Advantage in PAT scheme.

A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω

Description : A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is (A) 2.5 W (B) 5 W (C) 32.5 W (D) 35 W

Last Answer : A 200 V, 5 A d.c. energy meter is tested at its marked ratings. The resistance of the pressure circuit is 8000 Ω and that of current coil is 0.1 Ω. The power consumed when testing the meter with phantom loading with current circuit excited by a 6 V battery is 35 W

If a house has solar panels and all energy is free, then is it ok to leave the lights on?

Description : If a house has solar panels and all energy is free, then is it ok to leave the lights on?

Last Answer : I think it would be wise to not waste any energy whether it's free or paid. Every electronic item has a limited working lifespan, if you were to run it all the time, it's gonna break very soon. Aside ... then the short answer is Yes . You can waste as much as you want since you own this energy.

Is the energy crisis real?

Description : Is the energy crisis real?

Last Answer : Who is calling it a crisis? We have plenty of energy here in the US. OPEC has been aggrresive at limiting supply and raising prices.

What branch of science does research into tachyon energy computing ?

Description : What branch of science does research into tachyon energy computing ?

Last Answer : Right after we reach “the speed of light”. We are close, to speed of light, with the Large Hadron Collider.

Is it possible to convert infrared energy into electricity?

Description : Is it possible to convert infrared energy into electricity?

Last Answer : Silicon solar cells can convert the shorter wavelengths of IR to electricity: https://www.solarquotes.com.au/blog/uv-solar-panels/ You can also concentrate solar IR and use the ... .com/innovationtoronto.com/wp-content/uploads/2015/12/Solar-Thermal-Power-Plant_forcetoknow.com_.jpg?resize=627%2C221

Which takes less energy?

Description : Which takes less energy?

Last Answer : Send this Q to LuckyGuy!

Have they successfully converted energy to mass?

Description : Have they successfully converted energy to mass?

Last Answer : They?