In 8085, whenever a signal is received at TRAP terminal, its program execution is transferred to a subroutine

In 8085, whenever a signal is received at TRAP terminal, its program execution is transferred to a subroutine on address A) 0000 H B) 002C H C) 0024 H D) 0004 H
by

1 Answer

Answer :

In 8085, whenever a signal is received at TRAP terminal, its program execution is transferred to a subroutine on address 0024 H

by

Related questions

Explain Briefly The Trap Input For The 8085.?

Description : Explain Briefly The Trap Input For The 8085.?

Last Answer : Answer :The TRAP input is sensitive to both edge and level. The pulse width for this signal should be in excess as compared to the normal noise width. A second trap will never be able to ... to low transition. The pulse widths are wider than normal widths so as to prevent unwanted false triggers.

The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse

Description : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Last Answer : The clock frequency of an 8085 microprocessor based system is 3 MHz. What should be the minimum pulse width of the INTR signal so that it is recognized successfully? A) 5.6 µs B) 5.7 µs C) 5.8 µs D) 5.9 µs

Explain Briefly What Happens When The Intr Signal Goes High In The 8085?

Description : Explain Briefly What Happens When The Intr Signal Goes High In The 8085?

Last Answer : Answer :The INTR is a maskable interrupt for the 8085. It has the lowest priority and is also non vectored. When this INTR signal goes into the high state the following things occur / ... the processor saves the address of new instruction into the STACK and an interrupt service subroutine begins.

The 8085 Microprocessor has

Description : The 8085 Microprocessor has A) 8-bits Data bus and 16-bits Address bus B) 8-bits Data bus and 8-bits Address bus C) 16-bits Data bus and 16-bits Address bus D) 32-bits Data bus and 8-bits Address bus 

Last Answer : B) 8-bits Data bus and 8-bits Address bus. 

In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require

Description : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Last Answer : In 8085 microprocessor, how many T-states does OPCODE FETCH machine cycle normally require (i.e., when HOLD and WAIT signals are NOT forced)? A) 4 to 6 B) 3 to 8 C) 2 to 3 D) 8 to 12 

Then number of T-states of the instruction STA in 8085 microprocessor is

Description : Then number of T-states of the instruction STA in 8085 microprocessor is A) 10 B) 12 C) 13 D) 16 

Last Answer : Then number of T-states of the instruction STA in 8085 microprocessor is 13 

What is the size of memory which can be accessed by direct accessing in 8085 microprocessor?

Description : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

Last Answer : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

With reference to execution of work explain the following: i) Administrative approval ii) Technical sanctions

Description : With reference to execution of work explain the following: i) Administrative approval ii) Technical sanctions 

Last Answer : Administrative approval:  When any government department requires executing a project like network addition or extension work or installation of new project. It requires necessary administrative approval ... designated by government. The sanction given by authority is called technical sanction

How to Set a Mouse Trap

Description : How to Set a Mouse Trap

Last Answer : How to Set a Mouse Trap Are mice a problem in your home? Mouse traps remain one of the most effective ways of catching them and getting rid of them. Learn how to use and set them perfectly. When ... has a trap, and may learn to avoid it. Moving the trap around will help keep the trap effective.

How to Build a Mouse Trap Car

Description : How to Build a Mouse Trap Car

Last Answer : How to Build a Mouse Trap Car Introduction Toy cars can be a lot of fun to build, but most of them involve the use of some hard-to-come-by materials and tools that can be difficult to use. Not so ... face, so check out these tricks on getting rid of gnats, to drive them away from your home as well.

How to Build a Crab Trap

Description : How to Build a Crab Trap

Last Answer : How to Build a Crab Trap A delicious plate of crabs is delightful and mouthwatering, but the problem is, it can be very expensive. There's one solution to this though: catch them yourself. As long as ... like, as long as you have a well-functional crab trap. Follow these steps, and enjoy your catch!

Wave trap is used to trap waves of:

Description : Wave trap is used to trap waves of:  (A) Power frequencies (B) Higher frequencies entering generator or transformer units (C) All of the above (D) None of the above

Last Answer : Wave trap is used to trap waves of: Higher frequencies entering generator or transformer units

Wave trap is used to trap waves of?

Last Answer : Wave trap is used to trap waves of higher frequencies entering generator or transformer units.

Battery Terminal Cleaners

Description : Battery Terminal Cleaners

Last Answer : Corrosion is the enemy of car batteries. It can make the most high-end cars fail to start. Battery terminals are especially prone to corrosion because of the presence of water and acid in their ... be restored. If your battery terminals have too much deposit buildup, replace them with new ones.

Battery Terminal

Description : Battery Terminal

Last Answer : Automotive battery terminals can mean either the posts on a battery to which the jumper cables attach or the part of the cables that attach to the battery's posts. The latter are sometimes ... properly maintained for the car to run smoothly. Regular inspection helps to keep them in good condition.

What is internal voltage drop and terminal voltage?

Description : What is internal voltage drop and terminal voltage?

Last Answer : It is not permissible to just connect the positive terminal to the negative terminal of a cell with a copper wire. It will overheat and get damaged. This happens because the electromotive force (emf) ... than the nominal voltage (emf) of the cell and this lower voltage is called terminal voltage.

The terminal characteristics of a dc generator suitable for electric welders is

Description : The terminal characteristics of a dc generator suitable for electric welders is (A) separately excited generator (B) shunt generator (C) series generator (D) differentially compounded generator

Last Answer : The terminal characteristics of a dc generator suitable for electric welders is differentially compounded generator

A terminal where three on more branches meet is known as?

Description : A terminal where three on more branches meet is known as?

Last Answer : A terminal where three on more branches meet is known as node.

When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially...

Description : When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially and then slowly came to infinity position. This shows that capacitor is ?

Last Answer : When a capacitor was connected to the terminal of ohmmeter, the pointer indicated a low resistance initially and then slowly came to infinity position. This shows that capacitor is all right.

In a level compounded D.C. generator, full load terminal voltage is?

Last Answer : In a level compounded D.C. generator, full load terminal voltage is equal to no-load terminal voltage.

In over compounded generator, full load terminal voltage is?

Last Answer : In over compounded generator, full load terminal voltage is more than no load terminal voltage.

Describe Briefly The Accumulator Register Of 8085.?

Description : Describe Briefly The Accumulator Register Of 8085.?

Last Answer : Answer :It is one of the most important 8 bit register of 8085 It is responsible for coordinating input and output to and from the microprocessor through it. The primary purpose of ... logical operations. This accumulator register is mainly used for arithmetic, logical, store and rotate operations.

Explain Briefly The Flag Register In The 8085 Microprocessor.?

Description : Explain Briefly The Flag Register In The 8085 Microprocessor.?

Last Answer : Answer :The flag register in 8085 is an 8-bit register which contains 5 bit positions. These five flags are of 1bit F/F and are known as zero, sign, carry, parity and auxiliary carry. ... addition and subtraction operations. The parity flag is used for results containing an even number of one's.

Explain In Brief The Control And Timing Circuitry Of The 8085.?

Description : Explain In Brief The Control And Timing Circuitry Of The 8085.?

Last Answer : Answer :The timing and control circuitry section of the 8085 is responsible for the generation of timing and control signals so that instructions can be executed. The types of signals involved ... of control signals for the executions of instructions and for the sync between external devices.

Does The 8085 Support Externally Initiated Operations? If Yes How?

Description : Does The 8085 Support Externally Initiated Operations? If Yes How?

Last Answer : Answer :Yes the 8085 does support several externally initiated operations. The possible operations and the corresponding pins for them in the 8085 are as follows: It supports resetting ( this is possible ... It also has a HOLD pin which can basically pause the operation till required/ as required.

Mention The Different Types Of Data Transfers Possible In The 8085.?

Description : Mention The Different Types Of Data Transfers Possible In The 8085.?

Last Answer : Answer :The various types of data transfer operations possible are: Data transfer is possible between two registers. It is also possible between a memory location and a register. Also it can occur between ... . In reality data is never transferred it can only be copied from one location to another.

Explain All The Addressing Modes Of The 8085 With The Help Of Examples.?

Description : Explain All The Addressing Modes Of The 8085 With The Help Of Examples.?

Last Answer : Answer :The various types of addressing modes of the 8085 are as follows: Direct addressing: The instructions in itself contain the opearand. For ex. STA5513H or in/out instructions such as IN PORT C. ... etc. Implicit addressing: this form of addressing contains no operands. For ex. RAR, CMA etc.

Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Description : Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Last Answer : Answer :The various functional blocks of the 8085 microprocessor are: Registers Arithmetic logic unit Address buffer Increment / decrement address latch Interrupt control Serial I/O control Timing and control circuitry Instructions decoder and machine cycle encoder.

How Can Signals Be Classified For The 8085 Microprocessor?

Description : How Can Signals Be Classified For The 8085 Microprocessor?

Last Answer : Answer :The signals of the 8085 microprocessor based on their functions can be classified into 7 categories namely: Frequency and power signals Address and data buses The control bus Interrupt Signals Serial Input / Output signals DMA signals Reset Signals

Can An Rc Circuit Be Used As Clock Source For 8085?

Description : Can An Rc Circuit Be Used As Clock Source For 8085?

Last Answer : Answer :Yes, it can be used, if an accurate clock frequency is not required. Also, the component cost is low compared to LC or Crystal.

In 8085 Which Is Called As High Order / Low Order Register?

Description : In 8085 Which Is Called As High Order / Low Order Register?

Last Answer : Answer :Flag is called as Low order register & Accumulator is called as High order Register.

How Many Interrupts Are There In 8085?

Description : How Many Interrupts Are There In 8085?

Last Answer : Answer :There are 12 interrupts in 8085.

In What Way Interrupts Are Classified In 8085?

Description : In What Way Interrupts Are Classified In 8085?

Last Answer : Answer :In 8085 the interrupts are classified as Hardware and Software interrupts.

Which Stack Is Used In 8085?

Description : Which Stack Is Used In 8085?

Last Answer : Answer :LIFO (Last In First Out) stack is used in 8085.In this type of Stack the last stored information can be retrieved first.

What Are The Various Flags Used In 8085?

Description : What Are The Various Flags Used In 8085?

Last Answer : Answer :Sign flag, Zero flag, Auxillary flag, Parity flag, Carry flag.

What Are The Various Registers In 8085?

Description : What Are The Various Registers In 8085?

Last Answer : Answer :Accumulator register, Temporary register, Instruction register, Stack Pointer, Program Counter are the various registers in 8085.

List any four salient features of 8085 microprocessor

Description : List any four salient features of 8085 microprocessor

Last Answer : Features of 8085:  1. 16 address line so 216=64 Kbytes of memory can be addressed.  2. Operating clock frequency is 3MHz and minimum clock frequency is 500 KHz.  3. On chip bus controller ... duty cycle TTL clock  10. Provide 2 serial I/O lines, so peripheral can be interfaced with 8085 μp

What is the size of SP register in 8085 microprocessor?

Description :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits

Last Answer :  What is the size of SP register in 8085 microprocessor? A) 16 bits B) 8 bits C) 64 bits D) 48 bits

The ALE line of an 8085 microprocessor is used to

Description : The ALE line of an 8085 microprocessor is used to (A) latch the output of an I/O instruction into an external latch. (B) deactivate the chip-select signal from memory devices. (C) find the interrupt ... of the TRAP interrupt. (D) latch the 8 bits of address lines AD7-AD0 into an external latch.

Last Answer : The ALE line of an 8085 microprocessor is used to latch the 8 bits of address lines AD7-AD0 into an external latch.

When subroutine is called contents of program counter is location address of __ instruction following call instruction is stored on _ __and program execution is transferred to __ address. a. Non executable, pointer and subroutine b. Executable, Stack and Main program Cc. Executable, Queue and Subroutine d. Executable, Stack and Subroutine

Description : When subroutine is called contents of program counter is location address of __ instruction following call instruction is stored on _ __and program execution is transferred to __ address. a. Non ... , Stack and Main program Cc. Executable, Queue and Subroutine d. Executable, Stack and Subroutine

Last Answer : d. Executable, Stack and Subroutine

2.The period of a signal is 10ms. What is its frequency in kilohertz?

Description : .2.The period of a signal is 10ms. What is its frequency in kilohertz?

Last Answer : 100

An energy signal has G(f) = 20. Its energy density spectrum is

Description :  An energy signal has G(f) = 20. Its energy density spectrum is A) 20 B) 100 C) 400 D) 800  

Last Answer : 400

State different types of electrical signal and draw all types of waveforms.

Description : State different types of electrical signal and draw all types of waveforms.

Last Answer : Types of electrical signals 1) Sine wave 2) Triangular wave 3) Square wave Waveforms

basic characteristics of sound signal.

Description :  basic characteristics of sound signal.

Last Answer : Level and loudness: The amplitude of a sound wave determines its loudness or volume. A larger amplitude means a louder sound, and a smaller amplitude means a softer sound. The loudness of a ... the reproducing system should be capable of handling the maximum and minimum power in the same ratio. 

What is the significance of signal conditioner? Explain the need of following in mechatronics system. i) Isolator ii) Filter iii) Amplifier iv) Data converter

Description : What is the significance of signal conditioner? Explain the need of following in mechatronics system. i) Isolator ii) Filter iii) Amplifier iv) Data converter

Last Answer : Significance: Signal conditioning means manipulating an analog signal in such a way that it meets the requirements of the next stage for further processing. Signal inputs accepted by signal ... -frequency converters, current-to-voltage converters, current loop converters, and charge converters.  

List different methods of demodulation of FM signal.

Description : List different methods of demodulation of FM signal.

Last Answer : Balanced Slope detection Ratio detector Foster Seeley discriminator Phase locked loop demodulator 

For a signal conditioner explain the terms linearization and signal conversion.

Description : For a signal conditioner explain the terms linearization and signal conversion.

Last Answer : Definition :  1. linearization : Many primary elements produce nonlinear outputs and the signal must be linearized to produce a nearly ideal calibration. Specialized analog circuits such as offsetting circuits, ... signal. Even computer algorithms are also used. 2.Signal conversion :

Analog signal

Description : Analog signal

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is

Description :  If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is the transmitter from the target? A) 150 Km B) 150 m C) 15 Km D) 1500 m 

Last Answer :  If it takes a transmitted signal 1m sec to go up to the target and come back after reflection, how far is the transmitter from the target? A) 150 Km B) 150 m C) 15 Km D) 1500 m 

If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be

Description :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

Last Answer :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be Distorted