Basic electrical and electronics engineering practicals for diploma 22310 MSBTE

  • 1.Determine the permeability of magnetic material by plotting its BH curve
  • 2. Measure voltage, current and power in 1-phase circuit with resistive load.
  • 3. Measure voltage, current and power in R-L series circuit.
  • 4.Determine the transformation ratio (K) of 1-phase transformer.
  • 5.Connect single phase transformer and measure input and output quantities.
  • 6.Make Star and Delta connection in induction motor starters and measure the line and phase values.
by

6 Answers

Answer :

Practical no. 1

Aim: Determine the permeability of magnetic material by plotting its BH curve

Apparatus required:  voltmeter, ammeter, choke, autotransformer

Circuit diagram:

imageimage

image



Theory:

BH curve is the graph plotted between B (i.e. flux density) and H (i.e. magnetic field strength). H is taken on x-axis and B is taken on y-axis. Different magnetic materials have different BH curve. And non magnetic material have a straight line instead of curve.

Initially the B and H increases slowly but after instep B increases rapidly. And after knee point the B start getting saturated. And at Bmax there is a straight line called saturation. After Bmax the B will not increase further. BH curve is also called as magnetization curve.

Permeability (μ) is the ratio of B and H.


Procedure:

  1. Connect the equipments as shown in circuit diagram.

  2. Before turning on supply check whether the connection is correct or not.

  3. Keep the autotransformer on zero volt and turn on the mains.

  4. Slowly increase the voltage of autotransformer.

  5. Take the reading of current on ammeter and voltage on voltmeter.

  6. Draw the graph from current and voltage readings.

  7. Calculate the permeability from BH curve.


Precautions:

  1. Make the connections tight.

  2. Do not connect wrong wiring.

  3. Check the connection before turning on mains supply.

  4. Do not touch any conducting part when the supply is on.

  5. Avoid short circuit of connecting wires.


Result: Hence we have performed the practical and permeability of magnetic material is ________ H/m.

by

Answer :

Practical no. 2

Aim: Measure voltage, current and power in 1-phase circuit with resistive load.


Apparatus required:  voltmeter, ammeter, resistance, autotransformer


Circuit diagram:

image



Theory:

The single phase AC required two wires one is for line and second is for neutral. AC have changing magnitude and direction. AC have some limited frequency. In India the frequency used is 50 Hz. When we connect the resistive load the voltage and current give unity power factor. We can measure the current by connecting ammeter in series and voltage by connecting voltmeter in parallel. By multiplying the value of voltage and current we can obtained the value of power.



Procedure:

  1. Connect the equipments as shown in circuit diagram.

  2. Check the connection and turn on the switch.

  3. Take a reading of current on ammeter and voltage on voltmeter.

  4. Calculate power by multiplying voltage and current.


Precautions:

  1. Make the connections tight.

  2. Do not connect wrong wiring.

  3. Check the connection before turning on mains supply.

  4. Do not touch any conducting part when the supply is on.

  5. Avoid short circuit of connecting wires.


Result: Hence we have measured the voltage, current and power in 1-phase circuit with resistive load.

by

Answer :

Practical no. 3

Aim: Measure voltage, current and power in R-L series circuit.


Apparatus required:  voltmeter, ammeter, resistance, inductive load (choke),  autotransformer


Circuit diagram:

image



Theory:

The 1-phase AC is use in our homes which is 230 volts and 50 Hz. Many of our home loads are inductive like fan, washing machine etc.. When the inductive load is there current lags the voltage.



Procedure:

  1. Connect the equipments as shown in circuit diagram.

  2. Check the connection and turn on the switch.

  3. Take a reading of current on ammeter and voltage on voltmeter.

  4. Calculate power by multiplying voltage and current.


Precautions:

  1. Make the connections tight.

  2. Do not connect wrong wiring.

  3. Check the connection before turning on mains supply.

  4. Do not touch any conducting part when the supply is on.

  5. Avoid short circuit of connecting wires.


Result: Hence we have measured the voltage, current and power in 1-phase circuit with R-L load.

by

Answer :

Practical no. 4

Aim: Determine the transformation ratio (K) of 1-phase transformer.


Apparatus required:  voltmeter, transformer


Circuit diagram:

image



Theory:

There are two windings in Transformer one is called primary winding and second is called secondary winding. Primary winding have N1 number of turns and secondary winding have N2 number of turns.


The ratio of secondary number of turns N2 and primary number of turns N1 is called as transformation ratio. Transformation ratio is denoted by K.


Mathematically transformation ratio is given by,


Transformation ratio (K) = N2/N1 = V2/V1


Procedure:

  1. Connect the equipments as shown in circuit diagram.

  2. Check the connection and turn on the switch.

  3. Take a reading of voltage on voltmeter for both input and output.

  4. Calculate the transformation ratio from V2 and V1.


Precautions:

  1. Make the connections tight.

  2. Do not connect wrong wiring.

  3. Check the connection before turning on mains supply.

  4. Do not touch any conducting part when the supply is on.

  5. Avoid short circuit of connecting wires.


Result: Hence we have determined the transformation ratio (K) of 1-phase transformer.

by

Answer :

Practical no. 5

Aim: Connect single phase transformer and measure input and output quantities.


Apparatus required:  voltmeter, ammeter, transformer


Circuit diagram:

image



Theory:

The transformer is a static device which transforms electrical power by stepping up AC voltage and stepping down AC current or by stepping down AC voltage and stepping up AC current and keeping frequency constant.

There are two coils in transformer. one is called primary winding and second is called secondary winding. These two winding are inductively linked. The Transformer works on the principle of mutual induction. The principal of mutual induction states that if the current in one coil is changing this changing current will produce changing magnetic flux and this changing magnetic flux will produce EMF in in second coil. The EMF is called statically induced EMF.



Procedure:

  1. Connect the equipments as shown in circuit diagram.

  2. Check the connection and turn on the switch.

  3. Take a reading of current on ammeter and voltage on voltmeter for both input and output.

  4. Calculate the input and output quantities.


Precautions:

  1. Make the connections tight.

  2. Do not connect wrong wiring.

  3. Check the connection before turning on mains supply.

  4. Do not touch any conducting part when the supply is on.

  5. Avoid short circuit of connecting wires.


Result: Hence we have measured the input and output quantities of transformer.

by

Answer :

Practical no. 6

Aim: Make Star and Delta connection in induction motor starters and measure the line and phase values.


Apparatus required:  voltmeter, ammeter, induction motor


Circuit diagram:

image

image


Theory:

In case of induction motor starting heavy current flows but by connecting the stator coils in star connection we can reduce the starting current and when the induction motor is in running condition we can connect the stator coils in delta connection.

In case of star Line voltage (VL) = √3 Phase voltage (Vph) and Line current (IL) = Phase current (IPH). In case of delta Line voltage (VL) = Phase voltage (Vph) and Line current (IL) = √3 Phase current (IPH).


Procedure:

  1. Connect the equipment and wiring properly.

  2. Measure current using ammeter and voltage using voltmeter.



Precautions:

  1. Make the connections tight.

  2. Do not connect wrong wiring.

  3. Check the connection before turning on mains supply.

  4. Do not touch any conducting part when the supply is on.

  5. Avoid short circuit of connecting wires.


Result: Hence we have measured the line and phase value of star and delta connection.

by

Related questions

GATE 2020 syllabus electrical engineering

Description : GATE 2020 syllabus electrical engineering

Last Answer : EE: Electrical Engineering Section 1: Engineering Mathematics Linear Algebra: Matrix Algebra, Systems of linear equations, Eigenvalues, Eigenvectors. Calculus: Mean value theorems, Theorems of ... to dc converters, Single phase and three phase inverters, Sinusoidal pulse width modulation.

Write short notes on fire extinguishing methods adopted in electrical engineering.

Description : Write short notes on fire extinguishing methods adopted in electrical engineering. 

Last Answer : Stand 6 to 8 feet away from the fire and follow the four-step PASS procedure. If the fire does not begin to go out immediately, leave the area at once. Always be sure ... fire causing the particles to expand chemically inhibiting combustion and expelling the oxygen thereby smothering the flames. 

Electrical engineering

Description : Electrical engineering

Last Answer : https://youtu.be/ZKnK7Na2Frw

Electrical Engineering Android APP

Description : Electrical Engineering Android APP

Last Answer : Electrical Engineering Useful Android Apps 1. Electrical Engineering https://play.google.com/store/apps/details?id=electrical.electronics.engineering 2. Electrical Engineering Symbols https:/ ... .google.com/store/apps/details?id=electrical.engineering.qanda SHARE THIS USEFUL APPS

How To Make Basic Liquid Gel Soap

Description : How To Make Basic Liquid Gel Soap

Last Answer : 2 cups soap flakes or grated bar soap 1/2 gallon water 2 tbsp glycerin Mix ingredients together in a large pot or dutch oven. Set over low heat, stirring occasionally until the soap has dissolved. Transfer to a jar and cover tightly. For a less thick gel soap, use 1 gallon of water.

Basic Circuit Elements Symbols

Description : Basic Circuit Elements Symbols

Last Answer : Basic Circuit Elements Symbols

Basic Circuit Elements

Description : Basic Circuit Elements

Last Answer : Resistance ,current,voltage

Basic idea of generation

Description : Basic idea of generation 

Last Answer : Prior to the discovery of Faraday's Laws of electromagnetic discussion, electrical power was available from batteries with limited voltage and current levels. Although complicated in construction, D ... Therefore, area specific generating stations along with its distribution networks had to be used.

What are the basic requirements of locating wind power plant ?

Description : What are the basic requirements of locating wind power plant ?

Last Answer : The basic requirements of locating wind power plant:  1) The site should be selected where winds are strong i.e. where pressure of wind is high and there is continuity. 2) Wind pressure ... the turbine which can affect the system's overall performance. 10)Possibility to connect to power grid. 

Basic SI units

Description : Basic SI units

Last Answer : Basic SI units

In a circuit breaker the basic problem is to?

Last Answer : In a circuit breaker the basic problem is to transmit large power.

Describe the basic SHA operation with the help of its four mode specifications.

Description : Describe the basic SHA operation with the help of its four mode specifications.

Last Answer : Sample-and-hold amplifier (SHA) is a unity gain amplifier with a mode control switch where the input of the amplifier is connected to a time-varying signal. A trigger pulse at the mode control switch ... but other forms, such as optical and mechanical forms, are possible. Also denoted S/H.

basic gate drive circuit of GTO

Description : basic gate drive circuit of GTO

Last Answer : basic gate drive circuit of GTO

Electrical Wiring Who Say ?

Last Answer : Wire Through In load ( e.g. fan , lamp ) Etc. ) electric Power Supply To do Ordinary To the system Electric Waring Says. General In a sense Load Electric Power Supply To do For Of wires Ordinary In the system Being Electric Waring.

A 3 phase 50 Hz induction motor has full load speed of 970 rpm. Calculate no of poles and slip frequency.

Description : A 3 phase 50 Hz induction motor has full load speed of 970 rpm. Calculate no of poles and slip frequency.

Last Answer : The number of poles in an induction motor can be calculated using the following formula: No. of poles = (120 * frequency) / speed In this case, the number of poles would be calculated as follows: No. of poles = ( ... ) - 50 Hz = 8.08 Hz So the motor has 6 poles and a slip frequency of 8.08 Hz.

5) An iron ring of mean circumference of 80 cm is uniformly wound with 500 turns of wire. Calculate the value of flux density that a current of 1 A would produce in the ring. Assume relative permeability 1400.

Description : Please ripley me due to emergency

Last Answer : To calculate the flux density in the ring, you need to use the following formula: B = (μ * I * N) / (2 * π * r) where: B is the flux density in the ring (in teslas) μ is the relative permeability ... 2 * π * 0.127 m) = 0.53 T So the flux density in the ring would be approximately 0.53 teslas.

Why ELCB cannot work if Neutral input of ELCB does not connect to ground?

Description : Why ELCB cannot work if Neutral input of ELCB does not connect to ground?

Last Answer : ▪ ELCB is used to detect earth leakage fault. Once the phase and neutral are connected in an ELCB, the current will flow through phase and that same current will have to return neutral so ... that full fault current will come back through ELCB, and there will be no difference in current.

Refer to the circuit below . The power consumed by the element E is equal

Description : الرجوع إلى الدائرة أدناه. الطاقة التي يستهلكها العنصر E متساوية.

Last Answer : The power consumed the element E is equal to the  : P = V x I = 6V x 1 A = 6 W

Refer to the circuit below. The voltage V2, is equal to:

Description : Refer to the circuit below. The voltage V2, is equal to:

Last Answer : The answer to this question is -3V. Because 3V is in parallel with v2 and voltages in parallel are equal. But it is in opposite direction so the answer is -3V.

Direct Current (DC)

Description : Direct Current (DC) Next Topic : Alternating current (AC)

Last Answer : Direct Current (DC) is the unidirectional electric current. Uni meaning is one. And the flow of charge in same direction. We know that conventional current flow from positive terminal of battery to ... The magnitude of DC may constant or vary but direction do not change with respect to time.

Alternating current (AC)

Description : Alternating current (AC)

Last Answer : AC stands for Alternating Current meaning voltage or current that changes polarity or direction respectively over time. An Alternating Current (AC) is an electric current whose magnitude ... energy are known as alternators and are simpler construction than DC electromechanical generators.

Laptop What ?

Last Answer : Laptop Yes A Portable Computer.

circuit I mean What ?

Last Answer : electricity Source , conductor , control Instruments , Usage Machines , Protection Machines In combination Such A Path Whose The middle With Current Flowing To be Can Him Circuit Or Circuit Says.

House Wiring How much? Type, What? What ?

Last Answer : House Wiring Mainly Two Type. A ) Surface Wiring B ) Concealed Wiring Surface Wiring 5 Type : 1 ) Batten Wiring 2 ) Conduit Wiring 3 ) Clit Wiring 4 ) Casing Wiring 5 ) M. S. Wiring Concealed Wiring Again Two Type , 1 ) Concealed Conduit 2 ) Concealed Wire Wiring

Coulomb Who Say ?

Last Answer : any Conductive The middle With One Ampere Flow One Seconds Hold on Let's go Of Any Cross section With That Amount Infusion Flowing Is Him One Coulomb Says.

Power Who Say ?

Last Answer : that At the rate Electron Flowing Become Work Done Is Or That At the rate Electricity Power Other In strength Transformed Is Him Electric Power Says.

Power Who Say ?

Last Answer : any Person Or Of the object Single In time Made Of work The amount Power Says.

Magnetic Tell me Line What ?

Last Answer : any Magnetic In the case A Isolated The answer To the pole In the free state Placement If you do The pole That Path Circulation By Him Magnetic Ball line Says.

Mutual Inductance What?

Last Answer : that Features Or Of religion Due As well as Two Coil Of one Of current Of change As a result In the other Voltage Obsessed Is That said Religion Or Features Mutual Inductions Says.

Cable Who Say ?

Last Answer : Cable Being Electric Conductive His Whose The middle With Current Movement By

Her And Wire In The difference What ?

Last Answer : her And Cable In The difference Yes His Yes Just Only A Conductor Where Cable Two Or Even more Of the conductor A Group.

Process Who Say ?

Last Answer : Operating Of the system Of work Basic Single Who Process Says.

Stepper Motor What ?

Last Answer : Stepper Motor Such One Kind of Motor Which Equal In the corner Rotation Generated By To whom Step To say Is Since Step by step Step by step Equal In the corner Rotation Creation By So This one Stepper Motor Says.

Modulator What ?

Last Answer : Modulator Horo Modem Of In full The first Part.it Digital To the signal Analog In the signal Transformed By

Universal Motor What ?

Last Answer : that Motor AC And DC Both Supply A. Let's go Him Universal Motor Says.

Optical Fiber What ?

Last Answer : Optical Fiber Holo - glass Or Of plastic Too much Narrow , long Flexible But Solid Fiber Or Fiber. One Place From Other In place Electric Signal Exchange Of payment For Optical Fiber Use To do Is.

None Of the brand AC Good ?

Last Answer : Primary Idea : - First Home Type Understand AC To buy Will be That In the room AC Put it on In that If The window Stays However Likes According to Good Brand See ' window AC ' Bought To take Can. Of ... go 45 From 60 Thousands Money In The same Price In ' Gree ' Of the brand Window AC Found Will go

ACR Electricity Cost How much? To come Can ?

Last Answer : yours Tons Accordingly AC Use To do Can However That Depending By You How much? Tuk Watt A. That Usage Do His On. You A. Except Sources Accordingly Get out To do Can AC How much? Current Usage Doing. Source : ... = 6000/1000 = 8 _ _ In other words You 3 Hours Usage If you do 3 Unit Cost Will be

Fan Gently If you run What? Electricity Cost Less Is it

Last Answer : electricity Fan Gently Or Loud Anyway Let's go No. Why Electricity Same Cost Is 3 Because Fan To walk Control Is Regulator Or Regulator Through And Electricity Cost The work Regulator Before The end ... More Power Eat Regulator The rest Eat Fan. So Turn around Back Electricity Cost The same Being 3

a The fridge To buy I want to. Which one? More Electricity Affordable Will ?

Last Answer : Singer Refrigerator And Walton Refrigerator Electricity Affordable 3

Full form of BEE a. Bureau of energy efficient b. Basic electrical and electronics c. Basic thermal engineering d. None of the above.

Description : Full form of BEE a. Bureau of energy efficient b. Basic electrical and electronics c. Basic thermal engineering d. None of the above.

Last Answer : Bureau of energy efficient

Can a Schizophrenic study Engineering?

Description : Can a Schizophrenic study Engineering?

Last Answer : You can ask the university’s disability counselor. You might get an accommodation as a special student or take fewer classes, and go part time. Congratulations on improving your situation.

Which College is best for Marine Engineering?

Description : Which College is best for Marine Engineering?

Last Answer : The Merchant Marine Academy

Why is engineering so hard to get into?

Description : Why is engineering so hard to get into?

Last Answer : Because even top students flunk out. If you don’t have “the knack” and good academic discipline then understanding the core curriculum simply will not happen. It’s no picnic, it’s more like the revenant.

What is computer engineering like when compared to working at McDonalds?

Description : What is computer engineering like when compared to working at McDonalds?

Last Answer : answer:McDonalds you just take shit from your boss, and from customers while working a shit wage. My buddy describes his engineering job like hanging out in the college library working out a problem. ... those who feel their skills makes them a better human being/deserving of a higher wage.

I need a career change. I really enjoy math. Should I consider engineering?

Description : I need a career change. I really enjoy math. Should I consider engineering?

Last Answer : answer:While math is a big part of engineering, design and insight are a big part of it. Do you have interest in designing things? And what kind of engineering are you thinking of? Civil, ... to keep asking questions and not giving you answers, but these are things you need to think through.

What is biomedical engineering?

Description : What is biomedical engineering?

Last Answer : answer:Plenty of jobs, yes. Take a look at this and all the subfields: http://en.wikipedia.org/wiki/Bioengineering Bioprocess Engineering: Bioprocess Design, Biocatalysis, Bioseparation, Bioinformatics ... favorite is this http://en.wikipedia.org/wiki/Bioinformatics Google pours millions into this.

How do I go about getting an engineering internship in Tokyo?

Description : How do I go about getting an engineering internship in Tokyo?

Last Answer : The best place to start when looking for employment or an internship is your own network of family, friends, etc. Think through your connections-there might be someone therein who works in the ... often than not, this will lead you to that perfect summer engineering internship. Best of luck!

How different is cost engineering in North America?

Description : How different is cost engineering in North America?

Last Answer : answer:Cost engineering? I'm not sure about this one . but accounting practices are different. Asset management and liability listings are different because there are accepted practices in the US ... would be probably language. Terms and general language skills would probably be the biggest hurtle.

Where can I get FREE training in audio engineering?

Description : Where can I get FREE training in audio engineering?

Last Answer : TINSTAAFL. :)