Name the type of rectifier for each of following feature : (i) Highest rectifier efficiency (ii) Highest form factor (iii) Two diode rectifier circuit (iv) PIV = 2Vm.

Name the type of rectifier for each of following feature : (i) Highest rectifier efficiency (ii) Highest form factor (iii) Two diode rectifier circuit (iv) PIV = 2Vm.
by

1 Answer

Answer :

(i) Highest rectifier efficiency : Center tapped & Bridge full wave Rectifier 

(ii) Highest form factor : Center tapped & Bridge full wave Rectifier 

(iii) Two diode rectifier circuit : Center tapped full wave Rectifier 

(iv) PIV = 2Vm : Center tapped full wave Rectifier
by

Related questions

Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Description : Define given parameters and state their values for bridge rectifier (i) Ripple factor (ii) PIV of diode.

Last Answer : Ripple Factor: Ripple Factor is defined as the ratio of RMS value of the AC component of output to the DC or average value of the output. Mathematically it is expressed as, ( ... which appears across non-conducting reverse biased diode. (ii) PIV of diode for bridge rectifier-Vm

When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Last Answer : Feel Free to Answer

Define PIV, TUF, ripple factor, efficiency of rectifier.

Description : Define PIV, TUF, ripple factor, efficiency of rectifier.

Last Answer : PIV: Peak Inverse Voltage (PIV) is defined as the maximum negative voltage which appears across non-conducting reverse biased diode. TUF : Transformer Utilization Factor (TUF) is defined as the ratio of DC output ... Efficiency of rectifier: η = DC output power/ AC input power = PLdc / Pac

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Description : Define following parameter of rectifier: (i) Ripple factor (ii) Efficiency (iii) Peak Inverse Voltage (iv) Transformer utilization factor

Last Answer : (i) Ripple Factor - Ripple factor (γ) may be defined as the ratio of the root mean square (rms) value of the ripple voltage to the absolute value of the DC component of the ... the same rectifier. Effective VA Rating of transformer is the average of primary and secondary VA rating of transformer.

Define ripple factor and PIV of diode.

Description : Define ripple factor and PIV of diode.

Last Answer : 1. Ripple factor: It is define as ratio of R.M.S. value of AC component to the DC component in the output.  2. PIV : It is maximum reverse voltage that diode can withstand without destroying junction.

Define i)P-N junction diode ii) Depletion layer iii)Forward bias iv)Reverse bias of P-N junction diode

Description : Define i)P-N junction diode ii) Depletion layer iii)Forward bias iv)Reverse bias of P-N junction diode

Last Answer : i)P-N junction diode: It is a semiconductor device in which half of its region is P-type and other half is N-type.  ii) Depletion layer: The region where free electrons and free holes are absent ... and negative terminal is connected to p-side of p-n junction diode, it is said to be reverse bias.

Suggest the suitable diode type for rectifier circuit.

Description : Suggest the suitable diode type for rectifier circuit. 

Last Answer : Any general purpose diodes 1N4001 to 1N4007 series  Or Silicon diode & Germanium diode 

Give one feature of each of the following: (i) Mumbai port (ii) Marmagao port (iii) New Mangalore port (iv) Tuticorin port -SST 10th

Description : Give one feature of each of the following: (i) Mumbai port (ii) Marmagao port (iii) New Mangalore port (iv) Tuticorin port -SST 10th

Last Answer : (i) Mumbai port is the biggest one with a spacious natural and well shelpered harbour. (ii) Marmago port is the premier iron ore exporting port of the country. (iii) New Mangalore port, ... concentrates from Kudremukh mines. (iv) Tuticorin in Tamil Nadu has a natural harbour and rich hinterland.

What are the advantages of free wheeling diode in rectifier circuit?

Description : What are the advantages of free wheeling diode in rectifier circuit?

Last Answer : The input power factor is improved. It prevents the output voltage from becoming negative. Load current waveform is improved.

Which section of the circuit shown in the illustration smooths out highest degree of pulsations? EL-0085 A. I B. II C. III D. IV

Description : Which section of the circuit shown in the illustration smooths out highest degree of pulsations? EL-0085 A. I B. II C. III D. IV

Last Answer : Answer: C

Define ripple factor and PIV of HWR

Description : Define ripple factor and PIV of HWR

Last Answer : Peak Inverse Voltage (PIV) or Peak Reverse Voltage (PRV) refer to the maximum voltage a diode can withstand in the reverse-biased direction before breakdown. Also may be called Reverse Breakdown Voltage.

The dc current through each diode in a bridge rectifier equals : -

Description : The dc current through each diode in a bridge rectifier equals : - a) the load current b) half the dc load current c) twice the dc load current d) one-fourth the dc load current

Last Answer : The dc current through each diode in a bridge rectifier equals : - the load current

Compare AC & DC track circuits on i) Length of circuit ii) Application iii) Effect of stray currents. iv) Maintenance

Description : Compare AC & DC track circuits on i) Length of circuit ii) Application iii) Effect of stray currents. iv) Maintenance

Last Answer : Ans: i) Length of circuit - a) AC track circuit is having long length upto 3 to 5 km b) DC track circuit is having short length  ii)Application -a) AC track circuit is used ... ) Maintenance - a) AC track circuit has easier and cheaper maintenance b) DC track circuit has complicated maintenance 

Which of the following are the benefits of E-marketing? i) Speed ii) Reach and Penetration iii) Ease and Efficiency iv) Low Cost v) Targeted audience A) i, ii, iii and iv only B) ii, iii, iv and v only C) i, iii, iv and v only D) All i, ii, iii, iv and v

Description : Which of the following are the benefits of E-marketing? i) Speed ii) Reach and Penetration iii) Ease and Efficiency iv) Low Cost v) Targeted audience A) i, ii, iii and iv only B) ii, iii, iv and v only C) i, iii, iv and v only D) All i, ii, iii, iv and v

Last Answer : D) All i, ii, iii, iv and v

Differentiate induced draft and forced draft cooling towers based on (i) Location of fan (ii) Corrosion of blades (iii) Efficiency (iv) Fan size

Description : Differentiate induced draft and forced draft cooling towers based on (i) Location of fan (ii) Corrosion of blades (iii) Efficiency (iv) Fan size

Last Answer : Differentiate induced draft and forced draft cooling towers based on (i) Location of fan (ii) Corrosion of blades (iii) Efficiency (iv) Fan size

Define (i) I.P (ii) B.P (iii)Volumetric efficiency (iv)Isothermal efficiency of air compressor

Description : Define (i) I.P (ii) B.P (iii)Volumetric efficiency (iv)Isothermal efficiency of air compressor

Last Answer : i) I.P. - It is the ratio of polytrophic work into speed of compressor in revolution per second.   ii) B.P. - It is the power required to drive the compressor or power delivered to ... the ratio of isothermal power to the shaft power or brake power of motor required to drive the compressor  

Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Description : Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Last Answer : Parameter Class A Class B 

Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Description : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Last Answer : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Define the terms: (i) Lamp efficiency (ii) Luminous flux (iii) Luminaire (iv) Colour Rendering Index.

Description : Define the terms: (i) Lamp efficiency (ii) Luminous flux (iii) Luminaire (iv) Colour Rendering Index. 

Last Answer : i) Lamp efficiency or luminous efficiency: It is the ratio of luminous flux emitted by a lamp to the power consumed by the lamp. It is a reflection of efficiency of energy conservation ... of surfaces illuminated by a given source compare to those of the same surface under reference illuminant.

Write example of each type (i) Primary transducer (ii) Active transducer (iii) Electrical transducer (iv) Digital transducer

Description : Write example of each type (i) Primary transducer (ii) Active transducer (iii) Electrical transducer (iv) Digital transducer

Last Answer : (i) Active transducer:-Thermocouple, piezoelectric, photovoltaic cell (ii) Primary transducer:- Bourdon tube, bellows, (iii) Electrical transducer.:- LVDT,RVDT, Hall effect, strain gauge, ... , optical pyrometer, radiation pyrometer (iv) Digital transducer:- Linear Encoder, digital taco generator

Define : (i) Efficiency (ii) TUF of Rectifier

Description : Define : (i) Efficiency (ii) TUF of Rectifier

Last Answer : Rectifier efficiency (ɳ) : it is defined as the ratio of DC power to the applied input AC power. Transformer utilization factor: It is defined as the ratio of the DC power available at the load resistor and the AC rating of the secondary coil of a transformer.

Section IV of the circuit shown in the illustration is the _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Description : Section IV of the circuit shown in the illustration is the _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: A

What is the name of the simplest type of rectifier which uses one diode?

Description : What is the name of the simplest type of rectifier which uses one diode?

Last Answer : The half-wave rectifier.

Sketch circuit diagram of bridge rectifier with LC filter. State function of each component.

Description : Sketch circuit diagram of bridge rectifier with LC filter. State function of each component.

Last Answer :  Circuit diagram :  Components and its function: :  1. Transformer- An electrical device which transfers electrical energy from one electric circuit to other, without changing the frequency. The ... DC components.  4. Capacitor- It bypasses AC components if any and gives DC to load. 

Section III of the circuit shown in the illustration is a _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Description : Section III of the circuit shown in the illustration is a _____________. EL-0085 A. voltage regulator B. filter C. rectifier D. voltage transformer

Last Answer : Answer: B

What is the PIV of all type rectifiers?

Description : What is the PIV of all type rectifiers?

Last Answer : The PIV of rectifier: - Half wave rectifier=Vm, Center tape wave rectifier=2Vm Bridge full wave=Vm

Define each of following terms of operational amplifiers i) Slew rate ii) Input offset voltage iii) Voltage gain iv) Input capacitance

Description : Define each of following terms of operational amplifiers i) Slew rate ii) Input offset voltage iii) Voltage gain iv) Input capacitance

Last Answer : i) Slew rate:- Maximum rate of change of o/p voltage per unit of time. It is express in volt/µsec.  ii) Input offset voltage:- The voltage that must be applied between two ... capacitance that can be measured at either be inverting or non-inverting terminal with other terminal connected to ground.

What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Description : What effect does an open diode have on the output voltage of a half wave rectifier and on a full wave rectifier?

Last Answer : An open diode will result in no output from a half waverectifier, and an open diode will cut the output of a full waverectifier in half.

One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Description : One diode of a full-wave rectifier has burned out in a shorted condition. Therefore, the output will be ____________. A. zero B. a rectified half-wave C. a rectified full-wave D. equal to the AC input

Last Answer : Answer: D

A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Description : A full-wave rectifier has one diode burned out in an open condition, what will be the output characteristic of the device? A. Zero B. Half-wave rectified C. Full-wave rectified D. Equal to the AC input

Last Answer : Answer: B

Figure 'C' shown in the illustration represents a _________. EL-0078 A. silicon controlled rectifier B. light emitting diode C. photosensitive diode D. Zener diode

Description : Figure 'C' shown in the illustration represents a _________. EL-0078 A. silicon controlled rectifier B. light emitting diode C. photosensitive diode D. Zener diode

Last Answer : Answer: C

Figure 'D' shown in the illustration represents a _________. EL-0067 A. silicon controlled rectifier B. light emitting diode C. photosensitive diode D. Zener diode

Description : Figure 'D' shown in the illustration represents a _________. EL-0067 A. silicon controlled rectifier B. light emitting diode C. photosensitive diode D. Zener diode

Last Answer : Answer: B

Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

Why is a diode called as rectifier?

Description : Why is a diode called as rectifier?

Last Answer : Diode allows current to pass only when it is forward biased when AC voltage is applied across a diode. This property is used to rectify AC voltage. Hence a diode is called as rectifier.

For a diode to act as a rectifier, should it be connected in series or parallel with the load?

Description : For a diode to act as a rectifier, should it be connected in series or parallel with the load?

Last Answer : Series.

Which is the most important building block of electronic devices? (a) Diode (b) p-n junction (c) transistor (d) rectifier

Description : Which is the most important building block of electronic devices? (a) Diode (b) p-n junction (c) transistor (d) rectifier

Last Answer : b) p-n junction

A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free.

Description : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

Last Answer : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 5A, 7.07A

Can we use a zener diode as a rectifier?

Description : Can we use a zener diode as a rectifier?

Last Answer : Yes we can use zener diode as rectifier but it have limitations better to use normal diode. Zener diode have some different applications.

Consider the following statements and select the correct answer from the code given below: i. Rajasthan receives the highest solar radiation in the country. ii. India has the fifth largest installed wind power in the world. iii. The maximum amount of wind power is contributed by Tamil Nadu. iv. The primary source of uranium in India is Jaduguda. Codes: (A) i and ii (B) i, ii and iii (C) ii and iii (D) i and iv

Description : Consider the following statements and select the correct answer from the code given below: i. Rajasthan receives the highest solar radiation in the country. ii. India has the fifth largest installed wind power in the world. iii. The ... (A) i and ii (B) i, ii and iii (C) ii and iii (D) i and iv

Last Answer : Answer: D

Examine the following statements: (i) Factor of safety for steel should be based on its yield stress, (ii) Factor of safety for steel should be based on its ultimate stress, (iii) Factor of safety for concrete should be based on its yield stress, (iv) Factor of safety for concrete should be based on its ultimate stress. The correct statements are (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv

Description : Examine the following statements: (i) Factor of safety for steel should be based on its yield stress, (ii) Factor of safety for steel should be based on its ultimate stress, (iii) Factor of safety for concrete should be based on ... (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv

Last Answer : Answer: Option B

Which of the following statements are true? i) reactive current is necessary to build up the flux for the magnetic field of inductive devices ii) some portion of reactive current is converted into work iii) the cosine of angle between kVA and kVAr vector is called power factor iv) the cosine of angle between kW and kVA vector is called power factor a) i & iv b) ii & iii c) i & iii d) iii & iv

Description : Which of the following statements are true? i) reactive current is necessary to build up the flux for the magnetic field of inductive devices ii) some portion of reactive current is converted into work iii) the cosine of angle ... called power factor a) i & iv b) ii & iii c) i & iii d) iii & iv

Last Answer : a) i & iv

A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed

Description : A series combination of resistance 100 ohm and capacitance 50µf is connected in series to a 230 V, 50HZ supply. Calculate (i) Capacitive reactance (ii) Current (iii) Power factor (iv) Power consumed 

Last Answer : For RC series circuit

Which section of the circuit is responsible for maintaining a nearly constant voltage for all loads within its operating range? EL-0085 A. I B. II C. III D. IV

Description : Which section of the circuit is responsible for maintaining a nearly constant voltage for all loads within its operating range? EL-0085 A. I B. II C. III D. IV

Last Answer : Answer: D

Which section of the circuit shown in the illustration changes AC to DC? EL-0085 A. I B. II C. III D. IV

Description : Which section of the circuit shown in the illustration changes AC to DC? EL-0085 A. I B. II C. III D. IV

Last Answer : Answer: B

In which section of the 24 VDC power supply circuit illustrated, does the greatest change in voltage level take place when fed from ships power. EL-0085 A. I B. II C. III D. IV

Description : In which section of the 24 VDC power supply circuit illustrated, does the greatest change in voltage level take place when fed from ships power. EL-0085 A. I B. II C. III D. IV

Last Answer : Answer: A

Explain the following: (i) Blood group (ii) Short circuit (iii) Short sight (iv) International date line (v) Plaster of Paris

Description : Explain the following: (i) Blood group (ii) Short circuit (iii) Short sight (iv) International date line (v) Plaster of Paris

Last Answer : Answers: (i) Blood group A blood type (also called a blood group) is a classification of blood based on the presence or absence of inherited antigenic substances on the surface of red blood ... calcium sulfate hemihydrate, nominally CaSO4 0.5H2O. It is created by heating gypsum to about 150 °C.