Explain V- I method of measurement of medium resistance.

Explain V- I method of measurement of medium resistance. 
by

1 Answer

Answer :

image

In this method, use suitable source, ammeter and voltmeter and connect them as shown in the above diagram. Take reading of voltmeter and ammeter, then value of resistance = R = V/I Ω To minimise the error take 4 to 5 observation for the same resistance and take their average.

by

Related questions

Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

Description : Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

Last Answer : Methods for measurement of low resistance:  1. Ammeter voltmeter method  2. Kelvin's bridge method  3. Ohm meter method  4. Potentiometer method  5. Digital/analog multi-meter ... must be infinity for perfectly accurate measurement which is not possible.  2. Connection errors.

Name the method used to measure following resistances:- (i) Low resistance (ii) Medium resistance (iii) Insulation resistance (iv) Earth resistance.

Description : Name the method used to measure following resistances:- (i) Low resistance (ii) Medium resistance (iii) Insulation resistance (iv) Earth resistance.

Last Answer : Following are the methods used to measure resistances:-  (i) Low resistance: 1.Voltmeter-Ammeter Method 2. Kelvin's Double bridge Method  (ii) Medium resistance: 1.Voltmeter-Ammeter Method 2. ... of Charge Method  (iv) Earth resistance : 1. Fall of Potential Method 2. Earth tester

State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Description : State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Last Answer : State any two disadvantages of one wattmeter method of measurement of 3 phase power. Disadvantages of one wattmeter method:- 1. Only used for balanced load 2. It can not be used for ... connection then neutral point must be available 4. Delta connection must be opened to connect current coil.

State the range for low and medium resistance.

Description : State the range for low and medium resistance.

Last Answer : Low resistances: less than 1 ohm.  Medium resistances: 1 ohm to 0.1 Mega ohm. 

While calculating performance of medium transmission line, what assumptions are made in case of (i) Nominal 'T' Method (ii) Nominal 'TT' Method.

Description : While calculating performance of medium transmission line, what assumptions are made in case of (i) Nominal 'T' Method (ii) Nominal 'TT' Method. 

Last Answer : (i) Assumptions are made in case of Nominal 'T' Method:  a. It is assume that line capacitance is connected at center of transmission line. b. It is assume that half ... assumed that transmission line resistance & reactance per phase is connected in between two half transmission line capacitance 

what is mean by medium transmission line ?

Description : what is mean by medium transmission line ?

Last Answer : The transmission line which have length between 80 km to 250 km is known as medium transmission line.

With a neat diagram explain medium head hydro-electric power plants.

Description : With a neat diagram explain medium head hydro-electric power plants. 

Last Answer : Diagram of medium head hydro-electric power plants:  Explanation:- If head of water is between 30 and 100 m, the plant is called a medium-head plant. Potential energy of ... Francis turbines are normally used. Alternator required in these plants is of low speed and large in diameter. 

Explain significance and purpose of electrical measurement system.

Description : Explain significance and purpose of electrical measurement system.

Last Answer : ➢ Significance of Electrical Measurement System  1. The measurement is required for measurement of all physical quantities for e.g speed, velocity, temperature, pressure etc.  2. All electrical ... 4. These standards and references may changes time to time, area to area person to person 

In a 3-phase power measurement by two wattmeter method, both the wattmeters had identical readings...

Description : In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was?

Last Answer : In a 3-phase power measurement by two wattmeter method, both the watt meters had identical readings. The power factor of the load was unity.

Who played James Van Der Beek's girlfriend on Medium tonight?

Description : Who played James Van Der Beek's girlfriend on Medium tonight?

Last Answer : The actress who played pre-crash Harmony was Dahlia Salem, but the actress who played post-reconstruction “Brooke” was Morena Baccarin.

Susceptibility of the air medium is?

Last Answer : Susceptibility of the air medium is zero.

State how pressure measurement can be done using Dead weight tester.

Description : State how pressure measurement can be done using Dead weight tester.

Last Answer : The handle is fully drawn out and the oil is allowed to enter in the cylinder (i.e. gauge and piston) The weight to be measured is placed on the platform. Now the handle is turned ... of the area of the piston and the pressure indicated on the gauge is equal to the weight under measurement.

Define measurement and state the significance of electrical measurement system.

Description : Define measurement and state the significance of electrical measurement system.

Last Answer : Measurement: Measurement is essentially a process in which magnitude of a quantity is determined in comparison with another similar quantity with significant units. OR The measurement of a given ... x) The measurement conforms the validity of hypothesis and also adds to its understanding.

State the significance of term measurement.

Description : State the significance of term measurement. 

Last Answer : Measurement is the quantitative comparison between unknown quantities with known standard. For doing this process there is need of physical device, called as measuring instrument. The measurement confirms the validity of the hypothesis and also adds to its understanding.

Describe with working of LCR meter for measurement of inductance.

Description : Describe with working of LCR meter for measurement of inductance. 

Last Answer : working of LCR:- A LCR meter (Inductance (L), Capacitance (C), and Resistance (R) test equipment used to measure the inductance, capacitance and, resistance of a component. It works on the ... in parallel (as would be encountered in measuring a capacitor with a leaky dielectric) [Q setting ] 

A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Description : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Last Answer : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

With neat diagram explain calibration of energy meter by direct loading method.

Description : With neat diagram explain calibration of energy meter by direct loading method.

Last Answer : Calibration of Energy Meter by Direct Loading Method:  There are three methods for testing/calibration:  1. Long period dial test  2. Using rotary sub- standard meter  3. Using precision grade instruments  All ... of substandard meter in kWh  Then % error = [(D - DS)/DS] x 100

Explain spring control method with neat diagram.

Description : Explain spring control method with neat diagram.

Last Answer : Spring Control Method: As shown in the figure the inner ends of the both springs are attahced to the spindle ,while outer end of upper spring is attached to the lever and outer end of ... the springs are twisted in opposite direction to the motion of pointer and produce controlling torque.

Units of Measurement

Description : Units of Measurement

Last Answer : 1 horse power is 745.7 watts 1 horse power = work equal to lifting 550 lbs of weight to one foot for one second 1 calorie is equal to 4.2 Joules 1 barrel is equal to ... often chlorine or bromine. Use: as solvents, as aerosol propellants, in refrigeration. It is commonly used in refrigerator.

List the different level measurement methods.

Description : List the different level measurement methods. 

Last Answer : Liquid Level Measurement Direct method 1. Hook type 2. Sight glass gype 3. Float type 4. Dip stick Indirect method 1. Hydraustatic pressure type 2. Electrical type a) Capacitance level indicator b) Radiation level detector c) Ultrasonic level gauge 3. Radar type

Draw Bourdon tube with LVDT setup for pressure measurement.

Description : Draw Bourdon tube with LVDT setup for pressure measurement.

Last Answer : Bourdon tube with LVDT setup for pressure measurement.

sketch time period measurement by CRO.

Description : sketch time period measurement by CRO.

Last Answer : Horizontal sweep is turned ON and the display appealing on the screen is adjusted by varying different control knobs provided on the front panel of CRO, till the signal is suitably displayed ... Where m=Number of division in one complete cycle n=Setting of time base =Time/Division

different types of errors occurs in measurement.

Description : different types of errors occurs in measurement.

Last Answer : Generally errors are classified into three types: systematic errors, random errors and blunders. 1) Gross Errors 2) Random Errors 3) Systematic Errors Instrumental Errors Environmental ... to wrong observations or reading in the instruments particularly in case of energy meter reading. 

tern null as it applies to bridge measurement.

Description : tern null as it applies to bridge measurement.

Last Answer : Null measurements balance voltages so that there is no current flowing through the measuring device and, therefore, no alteration of the circuit being measured. Null measurements are generally more ... the use of standard voltmeters and ammeters, and they still have limits to their precision.

What are the factors influencing measurement errors?

Description : What are the factors influencing measurement errors?

Last Answer : The factor influencing measurement errors are accuracy, precision, range and bandwidth, sensitivity, resolution and uncertainty.

For measurement of radio frequency ac signals __________ type meter is used

Description : For measurement of radio frequency ac signals __________ type meter is used

Last Answer : For measurement of radio frequency ac signals thermo-couple type meter is used

Measurement of a non -electrical quantity involves the following four subsystems:

Description : Measurement of a non -electrical quantity involves the following four subsystems:  a) amplifier block b) display block c) instrumentation block d) transducer block  The correct, sequence in which these block occur is  (1) d,a,c,b (2) d, c, a, b (3) a, c, b, d (4) a, b, c, d

Last Answer : Measurement of a non -electrical quantity involves the following four subsystems:  a) amplifier block b) display block c) instrumentation block d) transducer block  The correct, sequence in which these block occur is d,a,c,b

The bridge most suited for accurate measurement of relative permittivity of dielectric materials is

Description : The bridge most suited for accurate measurement of relative permittivity of dielectric materials is (A) Carey Foster Bridge (B) Anderson’s bridge (C) Heaviside Bridge modified by Campbell. (D) Schering Bridge.

Last Answer : The bridge most suited for accurate measurement of relative permittivity of dielectric materials is Schering Bridge.

Accurate measurement of very low resistances is possible with

Description : Accurate measurement of very low resistances is possible with (A) Megger (B) Wheatstone Bridge (C) Kelvin’s Double Bridge (D) Wagner’s Earthing Device

Last Answer : Accurate measurement of very low resistances is possible with Kelvin’s Double Bridge

Commonly used instruments in power system measurement are?

Last Answer : Commonly used instruments in power system measurement are induction.

For measurement of inductance having high value, we should use?

Last Answer : For measurement of inductance having high value, we should use Hay's bridge.

For measurement of mutual inductance we can use?

Last Answer : For measurement of mutual inductance we can use Heaviside bridge.

What is measurement error ?

Description : What is measurement error ?

Last Answer : Measurement error :- Measurement is the process of comparing unknown quantity with known or standard quantity. Error is the difference between ... by fluctuations in reading measurement apparatus. Random error show different result for same repeated measurement.

State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material.

Description : State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material. 

Last Answer :  (i) Application of PVC paper : 1. It is used in slot lining or motor winding insulation purpose 2. For Insulation of Transformer winding (ii) Application of Porcelain : 1. Mainly used for manufacturing ... on withstand temperature : * H' & C' Class of insulation i e. 180° and above 180°C 

How to find total impedance Z, current I and Impedance angle ?

Description : How to find total impedance Z, current I and Impedance angle ?

Last Answer : How to find total impedance Z, current I and Impedance angle ?

Describe fire extinguishing method.

Description : Describe fire extinguishing method.

Last Answer : (i) Carbon Dioxide Extinguishing Systems  This type is the most suitable & widely recommended one for electrical fires. Carbon dioxide (CO2) extinguishers are normally Class C ... particles to expand chemically inhibiting combustion and expelling the oxygen thereby smothering the flames.

Merits of two wattmeter method

Description : Merits of two wattmeter method

Last Answer : Advantages of Two Wattmeter Method for 3-Phase Power Measurement: 1) It is used for balanced as well as unbalanced load. 2) For the star type load, it is not necessary to ... reactive volt-amperes for balanced loads also. 7) The circuit connections are independent of load connection.

Write one advantage and one disadvantage each for spring control method and gravity control method.

Description : Write one advantage and one disadvantage each for spring control method and gravity control method.

Last Answer : Advantages of Spring Control Method: 1) The spring-controlled meters may be used in any position. 2) In some instruments, springs can be used as current leads. 3) As springs are light in weight ... only. 2) Scale is non-uniform. 3) Control weights add to the weight of instrument.

List one advantage and one disadvantage of one wattmeter method.

Description : List one advantage and one disadvantage of one wattmeter method. 

Last Answer : Advantages:  1) Only one wattmeter is used.  2) Less number of connections.  3) Cost required is less.  Disadvantages:  1) Used only for 3- Φ balanced load and not for ... be accessible for connecting the Pressure coil.  3) Delta connection must be opened to connect current coil. 

List any four errors in induction type energy meter. Give method of compensation for each.

Description : List any four errors in induction type energy meter. Give method of compensation for each.

Last Answer : Errors in Induction Type Energy Meter with their Compensation:  1) Error due to friction: This error can be compensated by the additional shading band provided on the shunt electromagnet.  2) Phase ... error: This error can be compensated by providing a flux diverter' to the current magnet. 

The self GMD method is used to evaluate

Description : The self GMD method is used to evaluate

Last Answer : The self GMD method is used to evaluate inductance and capacitance

Explain the lighting scheme to be designed for each of the following: i) Special ward in hospitals ii) Dentist’s Cabin

Description : Explain the lighting scheme to be designed for each of the following: i) Special ward in hospitals ii) Dentist’s Cabin 

Last Answer : i) Special ward in hospital: For the patients in the wards, lighting should create a cozy and pleasant atmosphere. Lighting in the wards should be planned in such a way that it meets the specific ... we use such as cements and bonding agents that we use to restore your teeth back to health.

Explain the thermal triggering method of SCR. Enlist different triggering methods of SCR.

Description : Explain the thermal triggering method of SCR. Enlist different triggering methods of SCR.

Last Answer : Types of Triggering: 1) Forward voltage triggering 2) Thermal triggering (Temperature triggering) 3) Radiation triggering (Light triggering) 4) dv/dt triggering 5) Gate triggering ... generated leakage current increases. This current gets multiplied internally and thyristor is turned on. 

Draw and explain bulk correction method for power factor & control.

Description : Draw and explain bulk correction method for power factor & control.

Last Answer : Bulk correction method for power factor & control: i) Here individual starter controls the capacitors located at distribution panel. ii) Centralized compensation is employed in large industrial plants where many ... capacitor units in steps to maintain P.F. more than preset limit (0.95). 

Explain energy conservation method in lighting system by using installation of separate transformer / servo stabilizer.

Description : Explain energy conservation method in lighting system by using installation of separate transformer / servo stabilizer.

Last Answer : Energy conservation techniques by installation of separate transformer / servo stabilizer: The luminous efficiency of lamps depends upon the voltage applied across the terminals. It gives its best ... the voltage constant in that installation for giving best luminous efficiency of lamps.

Those of you who had "imaginary friends" as kids...Could you actually SEE them?

Description : Those of you who had "imaginary friends" as kids...Could you actually SEE them?

Last Answer : answer:No, I could not see them. I knew they were imaginary but they kept me company when I didn't have a playmate. More like talking to myself than having an actual imaginary friend, probably. ... because they haven't developed all of the societal filters yet and would be open to such a thing.

Drink Driving and who's responsible?

Description : Drink Driving and who's responsible?

Last Answer : Try to take the keys away from a person four times over the limit. That isn't going to end well. That is why you get the keys from them first. And it is really hard to judge how fucked up ... had just got to his house after dollar drink night and he seemed sober. Turns out he was fucked up too.

Why does every relationship question consist of one paragraph?

Description : Why does every relationship question consist of one paragraph?

Last Answer : My recent one wasn’t. I had lots of nifty little paragraphs. ;-P But I know what you’re talking bout’.

State suitable single phase motor for following applications: (i) Table fan (ii) Mixers and Grinders

Description : State suitable single phase motor for following applications: (i) Table fan (ii) Mixers and Grinders

Last Answer : Application Suitable Single Phase Motor Table Fan 1) Capacitor split phase motor 2) Capacitor start capacitor run motor Mixers and Grinders 1) Universal motor 2) A.C. Series motor

Compare the salient features of LED and CFL based on: i] Lamp Efficiency ii] Life span

Description :  Compare the salient features of LED and CFL based on: i] Lamp Efficiency ii] Life span 

Last Answer : Parameter LED CFL Lamp Efficiency  High (more than 70 lumen per watt) Comparatively less (50-60 lumen per watt) Life span (in working hours) 10000 3000