Write any two factors on which earth resistance depends.

1 Answer

Answer :

Factors on which earth resistance depends: (1) The shape and material used for the electrode (2) Depth of the electrode in the ground. (3) The specific resistance of the soil around the electrode (4) Moisture content in the soil. (5) Nature of soil 

Related questions

Description : State the procedure for testing of earth pit resistance with necessary diagrams.

Last Answer : Following procedure (Method) for testing of earth pit resistance with necessary diagrams. 1) Earth Tester : i) Three point method ii) Four point method 2) By Potential drop method 3 ... of that earthing pit. In this test the accuracy is less but electrical rods are not required. 

Description : Name the method used to measure following resistances:- (i) Low resistance (ii) Medium resistance (iii) Insulation resistance (iv) Earth resistance.

Last Answer : Following are the methods used to measure resistances:-  (i) Low resistance: 1.Voltmeter-Ammeter Method 2. Kelvin's Double bridge Method  (ii) Medium resistance: 1.Voltmeter-Ammeter Method 2. ... of Charge Method  (iv) Earth resistance : 1. Fall of Potential Method 2. Earth tester

Last Answer : Meggar is an instrument which measures the insulation resistance of an electric circuit relative to earth and one another.

Description : State the various factors governing selection of site for TPS. 

Last Answer : Following various factors governing selection of site for TPS.:- 1. It should locate near coal mines. 2. Sufficient quantity of water should be available. 3. Sufficient large space should ... availalbe nearly. To the extent possible, the thermal station should be far away from an aerodrome   

Description : State any four factors for selection of hydro power plant site. 

Last Answer : Following Factors to be kept while site selecting for Hydro power plant: 1) Quantity of water available :-Where high rainfall occures so that sufficent quantity of water can be stored for generation of ... be possible to divert the stream. 11. Sand, gravel, etc., should be available nearby.

Description : State any four factors for selection of site of wind power plant.

Last Answer : The Factors for selection of site for Wind Mills: 1) The site should be selected where winds are strong i.e. where pressure of wind is high and there is continuity (14.4- 16.2 km/h) ... 50m of the turbine which can affect the system's overall performance 10)Possibility to connect to power grid. 

Description : State any four factors for selecting location of nuclear power plant.

Last Answer : i) Seismicity: If the area of a nuclear site is seismically active, it may not be used for nuclear power plant.  ii) Water Availability: The nuclear power plants would need a ... Therefore, the site selected for such plant should have adequate arrangement for the disposal of radioactive waste.

Description : State any four factors governing Selection of site for thermal power station. 

Last Answer : Following Factors are to be considered:- 1. It should locate near coal mine. 2. Sufficient quantity of water should be available. 3. Sufficient large space should be available. 4. It should be located ... laws of the land and the town planning. 14. The interests of national defense must be served.

Description : State the factors affecting hysteresis loss.

Last Answer : i) Flux density ii) Frequency iii) Volume of the magnetic material iv) Nature of magnetic material

Description : What factors affect resistivity?

Last Answer : 1)type of material 2)temperature 3)length and area of cross section of conductor

Description : State two factors deciding size of conduit.

Last Answer : Following factors deciding size of conduit: 1) Types of wiring method 2) No. of wires carried out through conduit 3) Size of wires required for sub circuits which is carried out through conduit 4) Future expansion.

Description : List out factors affecting proximity effect. 

Last Answer : Factors affecting proximity effect: 1. Conductor size (diameter of conductor) 2. Frequency of supply current. 3. Distance between conductors. 4. Permeability of conductor material 

Description : State and explain any four factors governing selection of induction motor.

Last Answer : The factors governing the selection of Induction motor: 1) Load torque required at normal speed matches with available torque of motor. 2) Break down torque or pull out torque or maximum torque ... If selecting energy efficient motor the cost benefit analysis over the long run must be worked out.

Description : The main disadvantages of having poor power factors are:  (A) High cost of station and distribution equipment (B) Poor voltage regulation (C) High energy loss in conductor (D) All of the above

Last Answer : The main disadvantages of having poor power factors are:  (A) High cost of station and distribution equipment (B) Poor voltage regulation (C) High energy loss in conductor (D) All of the above

Description : What are the factors influencing measurement errors?

Last Answer : The factor influencing measurement errors are accuracy, precision, range and bandwidth, sensitivity, resolution and uncertainty.

Description : The Semiconductor strain gauges typically have much higher gauge factors than those of metallic strain gauges, primarily due to : (A) higher temperature sensitivity (B) higher Poisson’s ratio (C) higher piezoresitive coefficient (D) higher magnetostrictive coefficient

Last Answer : The Semiconductor strain gauges typically have much higher gauge factors than those of metallic strain gauges, primarily due to : higher piezoresitive coefficient

Last Answer : The resistance of armature winding depends on length of conductor, cross-sectional area of the conductor, number of conductors.

Description : Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

Last Answer : Methods for measurement of low resistance:  1. Ammeter voltmeter method  2. Kelvin's bridge method  3. Ohm meter method  4. Potentiometer method  5. Digital/analog multi-meter ... must be infinity for perfectly accurate measurement which is not possible.  2. Connection errors.

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Last Answer : equivalent resistance

Description : Define resistance with its unit.

Last Answer : Resistance is a measure of the degree to which a substance impedes the flow of electric current induced by a voltage.  Or Resistance is the opposition to current flow in an electrical circuit. Unit is ohm.(Ω)

Description : How does the resistance of a conductor compare to that of an insulator?

Last Answer : The resistance of a conductor can be significantly lower than the resistance of an insulator, depending on each material's atomic properties.

Description : Parallel Reactance and Resistance Example 1

Last Answer : Parallel Reactance and Resistance Example 1

Description : AC Circuits with Resistance but No Reactance

Last Answer : AC Circuits with Resistance but No Reactance AC Circuits with Resistance but No Reactance Series resistances let two resistances R 1 and R 2 are connected in series as shows in figure and there ... voltage. Voltage V A is common to both the branch hence voltage V A is common reference.

Description : Problems on resistance and resistivity

Last Answer : Problem on resistance and resistivity 1 : https://youtu.be/OqavD7OlZUs Problem on resistance and resistivity 2 : https://youtu.be/0eo8VO8cpwk Problem on resistance and resistivity 3 : https:// ... https://youtu.be/3neLRCTz0RQ Problem on resistance and resistivity 13 : https://youtu.be/vBCkvPOiztY

Description : Problem on temperature coefficient of resistance 3

Last Answer : Problem on temperature coefficient of resistance 3

Description : Problem on temperature coefficient of resistance 2

Last Answer : Problem on temperature coefficient of resistance 2

Description : Problem on temperature coefficient of resistance 1

Last Answer : Problem on temperature coefficient of resistance 1

Description : Problem on resistance and resistivity 13

Last Answer : Problem on resistance and resistivity 13

Description : Problem on resistance and resistivity 12

Last Answer : Problem on resistance and resistivity 12

Description : Problem on resistance and resistivity 11

Last Answer : Problem on resistance and resistivity 11

Description : Problem on resistance and resistivity 10

Last Answer : Problem on resistance and resistivity 10

Description : Problem on resistance and resistivity 9

Last Answer : Problem on resistance and resistivity 9

Description : Problem on resistance and resistivity 8

Last Answer : Problem on resistance and resistivity 8

Description : Problem on resistance and resistivity 7

Last Answer : Problem on resistance and resistivity 7

Description : Problem on resistance and resistivity 6

Last Answer : Problem on resistance and resistivity 6

Description : Problem on resistance and resistivity 5

Last Answer : Problem on resistance and resistivity 5

Description : Problem on resistance and resistivity 4

Last Answer : Problem on resistance and resistivity 4

Description : Problem on resistance and resistivity 3

Last Answer : Problem on resistance and resistivity 3

Description : Problem on resistance and resistivity 2

Last Answer : Problem on resistance and resistivity 2

Description : Problem on resistance and resistivity 1

Last Answer : Problem on resistance and resistivity 1

Description : State the use of shunt and series resistance used in extension of meter.

Last Answer : Use of shunt and series resistance: i) Use of shunt: To extend the range of Ammeter. ii) Use of series resistance: To extend the range of Voltmeter.

Description : State the range for low and medium resistance.

Last Answer : Low resistances: less than 1 ohm.  Medium resistances: 1 ohm to 0.1 Mega ohm. 

Description : Explain V- I method of measurement of medium resistance. 

Last Answer : In this method, use suitable source, ammeter and voltmeter and connect them as shown in the above diagram. Take reading of voltmeter and ammeter, then value of resistance = R = V/I Ω To minimise the error take 4 to 5 observation for the same resistance and take their average.

Description : Give classification of resistance based on their ranges.

Last Answer : Classification of Resistances Based on Their Ranges: 1) Low resistance: less than 1 ohm. 2) Medium resistance: 1 ohm to 0.1 Mega ohms. 3) High resistance: greater than 0.1 Mega ohms.

Description : Define pinch off voltage and drain resistance of FET.

Last Answer : 1 . Pinch-off Voltage: It is the value of the drain to source voltage VDS at which the drain current ID reaches its constant saturation value. Any further increase in VDS does not have any ... drain to source voltage to the change in drain current. It is also called AC/dynamic drain resistance.

Description : Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

Last Answer : a) E.M.F : The electromotive force of a battery is defined as the energy spent or the work done in taking a unit positive charge around the complete circuit of the battery i.e., in ... input required to restore the initial state of charge, under specified conditions, is called Watt-hr efficiency.

Description :  A resistor in which the resistance changes exponentially with change in temperature is called as A) Potentiometer B) Phototransistor C) Varactor D) Thermistor 

Last Answer :  A resistor in which the resistance changes exponentially with change in temperature is called as Thermistor 

Description : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

Last Answer : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

Description : Which of the following is the name given to resistance of thin films that are uniform in thickness? A) Area resistance B) Sheet resistance C) Filmy resistance D) None of these

Last Answer : Which of the following is the name given to resistance of thin films that are uniform in thickness? A) Area resistance B) Sheet resistance C) Filmy resistance D) None of these

Description : What is the resistance of a coil which draws 10 A and dissipates 1520 W? A) 152 Ω B) 15.2 Ω C) 1.52 Ω D) None of these

Last Answer : What is the resistance of a coil which draws 10 A and dissipates 1520 W? A) 152 Ω B) 15.2 Ω C) 1.52 Ω D) None of these