Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in temperature causes a tape to increase in length and the measured distance is too large (C) The straight distance between end points of a suspended tape is reduced by an amount called the sag correction (D) A 100 m tape of cross section 10 mm × 0.25 mm stretches about 10 mm under 5 kg pull

Pick up the incorrect statement from the following:
(A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing
by 0.005 m for each tape length
(B) An increase in temperature causes a tape to increase in length and the measured distance is
too large
(C) The straight distance between end points of a suspended tape is reduced by an amount
called the sag correction
(D) A 100 m tape of cross section 10 mm × 0.25 mm stretches about 10 mm under 5 kg pull
by

1 Answer

Answer :

(B) An increase in temperature causes a tape to increase in length and the measured distance is
too large
by

Related questions

A standard steel tape of length 30 m and cross-section 15 × 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of steel tape is 2.2 × 106 kg/cm2 , the correction to be applied is (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Last Answer : (A) - 0.000909 m

A tape of length and weight kg/m is suspended at its ends with a pull of kg, the sag correction is (A) l3W²/24P² (B) l²W3 /24P² (C) l²W²/24P 3 (D) lW²/24P

Description : A tape of length and weight kg/m is suspended at its ends with a pull of kg, the sag  correction is  (A) l3W²/24P² (B) l²W3 /24P² (C) l²W²/24P 3 (D) lW²/24P

Last Answer : (A) l3W²/24P²

If is the pull applied at the ends of tape in kg, is the length of tape between end marks in metres, is the weight of the tape in kg per metre run, then sag correction (A) C = w²l3 /24F² (B) C = w 3 l²/24F² (C) C = w²l3 /24F3 (D) C = 24w²l3 /80F

Description : If is the pull applied at the ends of tape in kg, is the length of tape between end marks in metres, is the weight of the tape in kg per metre run, then sag correction (A) C = w²l3 /24F² (B) C = w 3 l²/24F² (C) C = w²l3 /24F3 (D) C = 24w²l3 /80F

Last Answer : (A) C = w²l3 /24F²

The magnitude of ‘sag correction’ during measurement of lengths by taping is proportional to the : (a) Cube of the weight of the tape, in kg per m run (b) Cube root of the weight of the tape, in kg per m run (c) Square of the weight of the tape, in kg per m run (d) Square root of the weight of the tape, in kg per m run

Description : The magnitude of sag correction' during measurement of lengths by taping is proportional to the : (a) Cube of the weight of the tape, in kg per m run (b) Cube root of the weight of the tape, in kg per m run ... the tape, in kg per m run (d) Square root of the weight of the tape, in kg per m run

Last Answer : (c) Square of the weight of the tape, in kg per m run

While measuring with a metallic tape of 30 m length pull should be applied (A) 1 kg (B) 2 kg (C) 3 kg (D) 4 kg

Description : While measuring with a metallic tape of 30 m length pull should be applied  (A) 1 kg  (B) 2 kg  (C) 3 kg  (D) 4 kg 

Last Answer : (C) 3 kg

The sag of 50 m tape weighing 4 kg under 5 kg tension is roughly (A) 0.043 m (B) 0.053 m (C) 0.063 m (D) 0.083 m

Description : The sag of 50 m tape weighing 4 kg under 5 kg tension is roughly  (A) 0.043 m  (B) 0.053 m  (C) 0.063 m  (D) 0.083 m 

Last Answer : (D) 0.083 m 

Pick up the incorrect statement from the following: (A) Lead is the average horizontal straight distance between the borrow pit and the place of spreading soil (B) The lead is calculated for each block of the excavated area (C) The unit of lead is 50 m for a distance upto 500 m (D) The unit of lead is 1 km where the lead exceeds 2 km

Description : Pick up the incorrect statement from the following: (A) Lead is the average horizontal straight distance between the borrow pit and the place of spreading soil (B) The lead is calculated for each block of the ... a distance upto 500 m (D) The unit of lead is 1 km where the lead exceeds 2 km

Last Answer : (D) The unit of lead is 1 km where the lead exceeds 2 km

In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per 30 metre tape duly corrected for temperature, slope and sag, the angular error of closure not to exceed (where n is the number of traverse legs) (A) 50" n(B) 30" n(C) 60" n (D) None of these

Description : In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per ... legs) (A) 50" n (B) 30" n (C) 60" n (D) None of these

Last Answer : (A) 50" n

The static deflection of a spring under gravity, when a mass of 1 kg is suspended from it, is 1 mm. Assume the acceleration due to gravity g = 10 m/s^2. The natural frequency of this spring-mass system (in rad/s) is A 100 B 150 C 200 D 250

Description : The static deflection of a spring under gravity, when a mass of 1 kg is suspended from it, is 1 mm. Assume the acceleration due to gravity g = 10 m/s^2. The natural frequency of this spring-mass system (in rad/s) is A 100 B 150 C 200 D 250

Last Answer : A 100

If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2(D) D/6m(h1 - h2)3

Description : If h1 and h2 are the differences in level between ground and the formation levels, m is the slope of the sloping sides. D is the distance between the cross sections then, Prismoidal correction for a level section is (A) D/2m(h1 - h2) (B) D/3m(h1 - h2) (C) D/6m(h1 - h2)2 (D) D/6m(h1 - h2)3

Last Answer : (C) D/6m(h1 - h2)2

Pick up the correct statement regarding the centre line method of estimating a building (A) Product of the centre line of the walls and area of cross-section of any item, gives total quantity of the item (B) The centre line is worked out separately for different sections of walls of a building (C) The centre line length is reduced by half the layer of main wall joining the partition wall (D) All the above

Description : Pick up the correct statement regarding the centre line method of estimating a building (A) Product of the centre line of the walls and area of cross-section of any item, gives total quantity of the ... length is reduced by half the layer of main wall joining the partition wall (D) All the above

Last Answer : (D) All the above

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

Pick up the incorrect statement from the following: In a dry dock block made of hard wood, (A) Spacing of the blocks is 1.35 m (B) The lowest block is 1.8 m long 40 cm × 40 cm in cross-section (C) The middle block is 1.6 m long 40 cm × 40 cm in cross-section (D) None of these

Description : Pick up the incorrect statement from the following: In a dry dock block made of hard wood, (A) Spacing of the blocks is 1.35 m (B) The lowest block is 1.8 m long 40 cm × 40 cm in cross-section (C) The middle block is 1.6 m long 40 cm × 40 cm in cross-section (D) None of these

Last Answer : (D) None of these

Pick up the incorrect statement from the following regarding fire hydrants (A) Fire hydrants are fitted in water mains at 100 m to 150 m apart at fire (B) The minimum water pressure hydrants, is kept 1.5 kg/cm2 (C) The water at pressure 1 to 1.5 kg/cm2 is made available for 4 to 5 hours for constant use (D) None of these

Description : Pick up the incorrect statement from the following regarding fire hydrants (A) Fire hydrants are fitted in water mains at 100 m to 150 m apart at fire (B) The minimum water pressure hydrants, is kept 1.5 kg/ ... to 1.5 kg/cm2 is made available for 4 to 5 hours for constant use (D) None of these

Last Answer : (D) None of these

While measuring the distance between two points along upgrade with the help of a 20 m chain, the forward end of the chain is shifted forward through a distance (A) 20 (sin - 1) (B) 20 (cos - 1) (C) 20 (sec - 1) (D) 20 (cosec - 1)

Description : While measuring the distance between two points along upgrade with the help of a 20 m chain, the forward end of the chain is shifted forward through a distance (A) 20 (sin - 1) (B) 20 (cos - 1) (C) 20 (sec - 1) (D) 20 (cosec - 1)

Last Answer : (C) 20 (sec - 1)

If 50 m point of a 100 m tape is 50 cm off line, and 50 m sections are straight, an error is generated equal to (A) 1/10,000 (B) 1/15,000 (C) 1/20,000 (D) 1/25,000

Description : If 50 m point of a 100 m tape is 50 cm off line, and 50 m sections are straight, an error is generated equal to (A) 1/10,000 (B) 1/15,000 (C) 1/20,000 (D) 1/25,000

Last Answer : (C) 1/20,000

If is the difference in level between end points separated by , then the slope correction is [(h²/2l) + (h 4 /8l3 )]. The second term may be neglected if the value of in a 20 m distance is less than (A) ½ m (B) 1 m (C) 2 m (D) 3 m

Description : If is the difference in level between end points separated by , then the slope correction is [(h²/2l) + (h 4 /8l3 )]. The second term may be neglected if the value of in a 20 m distance is less than (A) ½ m (B) 1 m (C) 2 m (D) 3 m

Last Answer : (D) 3 m

Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of column should not exceed 300 mm (C) Reinforcing bars in a column should not be less than 12 mm in diameter (D) The number of longitudinal bars provided in a circular column should not be less than four

Description : Which of the following statements is incorrect? (A) Minimum cross sectional area of longitudinal reinforcement in a column is 0.8% (B) Spacing of longitudinal bars measured along the periphery of ... (D) The number of longitudinal bars provided in a circular column should not be less than four

Last Answer : Answer: Option D

A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 × 106 N/mm2 , the depth of the joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm

Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so  that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the  value of E = 0.2 ... joist, is  (A) 200 mm  (B) 250 mm  (C) 300 mm  (D) 400 mm 

Last Answer : (D) 400 mm 

Pick up the correct statement from the following: (A) The directions of plumb lines suspended at different points in a survey are not strictly parallel (B) In surveys of small extent, the effect of curvature may be ignored and the level surface of the earth is assumed as horizontal (C) In surveys of large extent, the effect of curvature of the earth must be considered (D) All the above

Description : Pick up the correct statement from the following: (A) The directions of plumb lines suspended at different points in a survey are not strictly parallel (B) In surveys of small extent, the effect of ... of large extent, the effect of curvature of the earth must be considered (D) All the above

Last Answer : (D) All the above

A steel rod 1 metre long having square cross section is pulled under a tensile load of 8 tonnes. The extension in the rod was 1 mm only. If Esteel = 2 × 106 kg/cm2 , the side of the rod, is (A) 1 cm (B) 1.5 cm (C) 2 cm (D) 2.5 cm

Description : A steel rod 1 metre long having square cross section is pulled under a tensile load of 8 tonnes. The  extension in the rod was 1 mm only. If Esteel = 2 × 106  kg/cm2 , the side of the rod, is  (A) 1 cm  (B) 1.5 cm  (C) 2 cm  (D) 2.5 cm 

Last Answer : (C) 2 cm 

If the above tape weights 0.001 kg/ft, sag is a.2.73 ft b.3.13 ft c.2.90 ft d.3.03 ft e.107 dynes

Description : If the above tape weights 0.001 kg/ft, sag is a.2.73 ft b.3.13 ft c.2.90 ft d.3.03 ft e.107 dynes

Last Answer : c. 2.90 ft

Pick up the incorrect statement from the following: (A) Dimensions are measured to the nearest 0.01 m (B) Areas are measured to the nearest 0.01 sq.m (C) Cubic contents are measured to the nearest 0.1 cum (D) Weights are measured to the nearest 0.001 tonnes

Description : Pick up the incorrect statement from the following: (A) Dimensions are measured to the nearest 0.01 m (B) Areas are measured to the nearest 0.01 sq.m (C) Cubic contents are measured to the nearest 0.1 cum (D) Weights are measured to the nearest 0.001 tonnes

Last Answer : (D) Weights are measured to the nearest 0.001 tonnes

A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444

Description : A cantilever shaft having 50 mm diameter and a length of 300mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m^2. Determine the static deflection of shaft in mm. A 0.144 B 0.244 C 0.344 D 0.444

Last Answer : A 0.144

A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 3 . Determine the static deflection of the shaft in mm. a) 0.147 b) 0.213 c) 0.132 d) 0.112

Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 3 . Determine the static deflection of the shaft in mm. a) 0.147 b) 0.213 c) 0.132 d) 0.112

Last Answer : a) 0.147

A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre? (A) 5 mm (B) 0.5 mm (C) 0.05 mm (D) 0.005 mm

Description : A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre? (A) 5 mm (B) 0.5 mm (C) 0.05 mm (D) 0.005 mm

Last Answer : (A) 5 mm

In measuring critical speed of shaft experiment, it was found that the frequency ratio is 0.707 when the eccentricity is 0.05 m. what will be the displacement of the system. A. 0.05 m B. 0.005 m C. 0.5 m D. Infinite

Description : In measuring critical speed of shaft experiment, it was found that the frequency ratio is 0.707 when the eccentricity is 0.05 m. what will be the displacement of the system. A. 0.05 m B. 0.005 m C. 0.5 m D. Infinite

Last Answer : A. 0.05 m

Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section (C) Distance of the C.G. of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Description : Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to (A) Shear force (B) Area of the section ... . of the area from its neutral axis (D) Moment of the beam section about its neutral axis

Last Answer : Answer: Option D

Pick up the incorrect statement from the following: (A) Iron salts produce heavy flocks and hence remove more suspended matter (B) Iron salts remove hydrogen sulphides (C) Iron salts can be used over a limited range of pH values (D) Iron salts impart corrosiveness to water

Description : Pick up the incorrect statement from the following: (A) Iron salts produce heavy flocks and hence remove more suspended matter (B) Iron salts remove hydrogen sulphides (C) Iron salts can be used over a limited range of pH values (D) Iron salts impart corrosiveness to water

Last Answer : (C) Iron salts can be used over a limited range of pH values

A pile of length carrying a uniformly distributed load per metre length is suspended at the centre and from other two points 0.15 L from either end ; the maximum hogging moment will be (A) WL²/15 (B) WL²/30 (C) WL²/60 (D) WL²/90

Description : A pile of length carrying a uniformly distributed load per metre length is suspended at the centre and from other two points 0.15 L from either end ; the maximum hogging moment will be (A) WL²/15 (B) WL²/30 (C) WL²/60 (D) WL²/90

Last Answer : Answer: Option D

Pick up the incorrect statement from the following: The torsional resistance of a shaft is directly proportional to (A) Modulus of rigidity (B) Angle of twist (C) Reciprocal of the length of the shaft (D) Moment of inertia of the shaft section

Description : Pick up the incorrect statement from the following: The torsional resistance of a shaft is directly  proportional to  (A) Modulus of rigidity  (B) Angle of twist  (C) Reciprocal of the length of the shaft  (D) Moment of inertia of the shaft section 

Last Answer : (D) Moment of inertia of the shaft section 

The sag in a tape 100 ft long held between two supports 99.8 ft aprat at the same level is a.3.32 ft b.0.98 ft c.2.73 ft d.1.87 ft e.107 dynes

Description : The sag in a tape 100 ft long held between two supports 99.8 ft aprat at the same level is a.3.32 ft b.0.98 ft c.2.73 ft d.1.87 ft e.107 dynes

Last Answer : c. 2.73 ft

A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550

Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free enD. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. A. 575B. 625 C. 525 D. 550

Last Answer : A. 575

A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Determine the frequency of transverse vibrations of the shaft. a) 31 b) 35 c) 37 d) 41

Description : A cantilever shaft having 50 mm diameter and a length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Determine the frequency of transverse vibrations of the shaft. a) 31 b) 35 c) 37 d) 41

Last Answer : d) 41

A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550

Description : A cantilever shaft having 50 mm diameter and length of 300 mm has a disc of mass 100 kg at its free end. The Young’s modulus for the shaft material is 200 GN/m 2 . Calculate the natural longitudinal frequency in Hz. a) 575 b) 625 c) 525 d) 550

Last Answer : a) 575

If is the difference in height between end points of a chain of length , the required slope correction is (A) h²/2l (B) h/2l (C) h²/l (D) 2h²/2l

Description : If is the difference in height between end points of a chain of length , the required slope correction is (A) h²/2l (B) h/2l (C) h²/l (D) 2h²/2l

Last Answer : (A) h²/2l

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m and 284.295 m respectively, the collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m

Description : A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m ... collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m

Last Answer : (D) 0.060 m

The slope correction for a 3° slope for a length of 100 m, is (A) -0.11 m (B) -0.12 m (C) -1.87 m (D) -0.137 m

Description : The slope correction for a 3° slope for a length of 100 m, is  (A) -0.11 m  (B) -0.12 m  (C) -1.87 m  (D) -0.137 m

Last Answer : (D) -0.137 m

Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these

Description : Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these

Last Answer : (D) None of these

A straight rod of mass m and lenth `L` is suspended from the identical spring as shown in the figure The spring stretched by a distance of `x_(0)` due

Description : A straight rod of mass m and lenth `L` is suspended from the identical spring as shown in the figure The spring stretched by a distance of `x_(0)` due

Last Answer : A straight rod of mass m and lenth `L` is suspended from the identical spring as shown in the figure The spring ... `(mgR)/(2LE)` D. `(mgR)/(E)`

Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) The rate of flow of water through a vertical strip of the aquifer of unit width and full depth under a unit hydraulic gradient, is called coefficient of transmissibility (C) The flow of water through aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Description : Pick up the incorrect statement from the following: (A) The rate of flow of water through a unit cross-sectional area under a unit hydraulic gradient, is called coefficient of permeability (B) ... aquifers, is governed by the Darcy's law (D) The term 'transmissibility' was introduced by Meinzer

Last Answer : Answer: Option D

If a rectangular beam measuring 10 × 18 × 400 cm carries a uniformly distributed load such that the bending stress developed is 100 kg/cm2 . The intensity of the load per metre length, is (A) 240 kg (B) 250 kg (C) 260 kg (D) 270 kg

Description : If a rectangular beam measuring 10 × 18 × 400 cm carries a uniformly distributed load such that the bending stress developed is 100 kg/cm2 . The intensity of the load per metre length, is (A) 240 kg (B) 250 kg (C) 260 kg (D) 270 kg

Last Answer : (B) 250 kg

A mass of 10 kg when suspended from a spring causes a static deflection of 0.01m. Find the spring stiffness for the same system. A 9810 N/m B 8910 N/m C 1098 N/m D 9801 N/m

Description : A mass of 10 kg when suspended from a spring causes a static deflection of 0.01m. Find the spring stiffness for the same system. A 9810 N/m B 8910 N/m C 1098 N/m D 9801 N/m

Last Answer : A 9810 N/m

A mass of 10 kg when suspended from a spring causes a static deflection of 0.01m. Find the spring stiffness for the same system. A 9810 N/m B 8910 N/m C 1098 N/m D 9801 N/m

Description : A mass of 10 kg when suspended from a spring causes a static deflection of 0.01m. Find the spring stiffness for the same system. A 9810 N/m B 8910 N/m C 1098 N/m D 9801 N/m

Last Answer : D 9801 N/m

A mass of 10 kg when suspended from a spring causes a static deflection of A 0.01m. Find the spring stiffness for the same system. (A) 9810 N/m (B) 8910 N/m (C)1098 N/m (D) 9801 N/m

Description : A mass of 10 kg when suspended from a spring causes a static deflection of A 0.01m. Find the spring stiffness for the same system. (A) 9810 N/m (B) 8910 N/m (C)1098 N/m (D) 9801 N/m

Last Answer : A) 9810 N/m

If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm(C) 150 cm (D) 200 cm

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm

Last Answer : Answer: Option C

A steel rod of 2 cm diameter and 5 metres long is subjected to an axial pull of 3000 kg. If E = 2.1 × 106 , the elongation of the rod will be (A) 2.275 mm (B) 0.2275 mm (C) 0.02275 mm (D) 2.02275 mm

Description : A steel rod of 2 cm diameter and 5 metres long is subjected to an axial pull of 3000 kg. If E = 2.1 × 106 , the elongation of the rod will be (A) 2.275 mm (B) 0.2275 mm (C) 0.02275 mm (D) 2.02275 mm

Last Answer : (B) 0.2275 mm

A string of linear mass density 0.005 kg/m is stretched by a force F=2t^2 N

Description : A string of linear mass density 0.005 kg/m is stretched by a force F=2t^2 N

Last Answer : A string of linear mass density 0.005 kg/m is stretched by a force F=2t^2 N ( t is in sec) as shown in figure. ... 24.5 m/s C) 32 m/s D) 40 m/s

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs