If 50 m point of a 100 m tape is 50 cm off line, and 50 m sections are straight, an error is generated
equal to
(A) 1/10,000
(B) 1/15,000
(C) 1/20,000
(D) 1/25,000

1 Answer

Answer :

(C) 1/20,000

Related questions

Description : Pick up the incorrect statement from the following: (A) While measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length (B) An increase in ... ) A 100 m tape of cross section 10 mm 0.25 mm stretches about 10 mm under 5 kg pull

Last Answer : (B) An increase in temperature causes a tape to increase in length and the measured distance is too large

Description : If the original scale of a negative is 1 : 10,000, the ground resolution, considering that we get nearly 20 lines pair per mm, will be : (a) 50 mm (b) 20 cm (c) 2 m (d) 25 cm

Last Answer : (d) 25 cm

Description : A rectangular beam 20 cm wide is subjected to a maximum shearing force of 10,000 kg, the corresponding maximum shearing stress being 30 kg/cm2 . The depth of the beam is (A) 15 cm (B) 20 cm (C) 25 cm (D) 30 cm

Last Answer : (C) 25 cm

Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2  MN/mm2  and Poisson's ratio is 0.25, the change in the volume of the bar is:  (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm

Last Answer : (C) 3.125 cm

Description : Alfa Company Limited acquired the business of M/s Bharat Traders. The valuation of the items acquired was-building Rs. 1,20,000; machinery Rs. 80,000 and stock-in-trade Rs. 30,000. The company issued in lieu of the above items 800, ... ) Rs. 2,30,000 (B) Rs. 1,00,000 (C) Rs. 50,000 (D) Rs. 30,000

Last Answer : Answer: Rs. 30,000

Description : A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m ... collimation error per 100 m is (A) 0.015 m (B) 0.030 m (C) 0.045 m (D) 0.060 m

Last Answer : (D) 0.060 m

Description : A machine is purchased for Rs. 10,000,00 and has an estimated life of 10 years. The salvage value at the end of 10 years is Rs. 1,50,000. The book value of the machine at the end of 5 years using general straight line method ... Rs. 4,75,000 (B) Rs. 5,75,000 (C) Rs. 6,50,000 (D) Rs. 8,50,000

Last Answer : (B) Rs. 5,75,000

Description : The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm  for an eccentric load 100 t for non-development of tension, is  (A) 2.75 cm  (B) 3.00 cm  (C) 3.50 cm  (D) 4.25 cm

Last Answer : (D) 4.25 cm

Description : From the point of tangency before an intersection, the route markers are fixed at a distance of (A) 15 m to 30 m (B) 20 m to 35 m (C) 40 m to 50 m (D) 100 m to 150

Last Answer : Answer: Option D

Description : Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of ... should be limited to (A) 14.14 m (B) 28.28 m (C) 200 m (D) None of these

Last Answer : (B) 28.28 m

Description : The maximum non-verticality of the bore of a well 200 m deep, may be permitted up to (A) 25 cm (B) 50 cm (C) 75 cm (D) 100 cm

Last Answer : (D) 100 cm

Description : Metric chains are generally available in (A) 10 m and 20 m length (B) 15 m and 20 m length (C) 20 m and 30 m length (D) 25 m and 100 m length

Last Answer : (C) 20 m and 30 m length

Description : A singly reinforced concrete beam of 25 cm width and 70 cm effective depth is provided with 18.75 cm2 steel. If the modular ratio (m) is 15, the depth of the neutral axis, is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

Description : The stresses developed in concrete and steel in reinforced concrete beam 25 cm width and 70 cm effective depth, are 62.5 kg/cm2 and 250 kg/cm2 respectively. If m = 15, the depth of its neutral axis is (A) 20 cm (B) 25 cm (C) 30 cm (D) 35 cm

Last Answer : Answer: Option C

Description : The molecular weight of light chains is (A) 10,000–15,000 (B) 20,000–25,000 (C) 25,000–50,000 (D) 50,000–75,000

Last Answer : Answer : B

Description : Non-passing sight distance along a road is the longest distance at which the driver of a moving vehicle, may see an obstacle on the pavement (A) 10 cm high (B) 25 cm high (C) 50 cm high (D) 100 cm high

Last Answer : Answer: Option A

Description : Depending upon the size of the tractor the width of the tracks varies for a) 10-50 cm b) 15.50 cm c) 20 – 25 cm d) 25-50 cm

Last Answer : c) 20 – 25 cm

Description : Which of the following introduces an error of about 1 in 1000 if 20 m chain is used? (A) Length of chain 20 mm wrong (B) One end of the chain 0.9 m off the line (C) One end of chain 0.9 m higher than the other (D) All the above

Last Answer : (D) All the above

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

Description : While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of ... true position will be (A) 0.02 cm (B) 0.15 cm (C) 0.2 cm (D) 0.1 cm

Last Answer : (B) 0.15 cm

Description : Cost of fencing a circular plot at the rate of Rs.15 per metre is Rs.3, 300. What will be the cost of flooring the plot at the rate of Rs.100 per square metre? a) Rs.3, 85,000 b) Rs.4, 70,000 c) Rs.2, 25,000 d) Rs.3, 50,000 e) Rs.2, 95,000

Last Answer : Perimeter of plot = 3300/15 = 220 meter 2πr = 220 2 × 22/7 × r = 220 r = 35 m. Area of plot = πr^2 = 22/7 × 35 × 35 = 3850 mt^2 Cost of flooring = 3850 × 100=Rs. 385000 Answer: a)

Description : In precision theodolite traverse if included angles are read twice and the mean reading accepted using both verniers having a least count of 30". Assuming the instrument to be in perfect adjustment, linear measurements correct to 6 mm per ... legs) (A) 50" n (B) 30" n (C) 60" n (D) None of these

Last Answer : (A) 50" n

Description : To prevent movement of moisture from sub-grade to road pavement on embankments about 0.6 m to 1 m higher than water table, the thickness of cut off layer of coarse sand used, is (A) 15 cm (B) 20 cm (C) 30 cm (D) None of these

Last Answer : Answer: Option D

Description : The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Last Answer : Ans: (c) Correct Answer is: 0.45 m

Description : A jet of water of cross-sectional area 20 sq. cm impinges on a plate at an angle of 60? with a velocity of 10 m/sec. Neglecting the friction between the jet and plate (density of water 1000/9.81 kgm-1 sec2 per cubic meter), the ... a.15 - 20 kg b.20 - 25 kg c.5 - 10 kg d.25 - 30 kg e.10 - 15 kg

Last Answer : a. 15 - 20 kg

Description : Dimensions of a beam need be changed if the shear stress is more than (A) 10 kg/cm2 (B) 15 kg/cm2 (C) 20 kg/cm2 (D) 25 kg/cm

Last Answer : Answer: Option C

Description : Minimum thickness of the base of a flexible pavement, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : Answer: Option A

Description : In welded wire mesh, the longitudinal wire is placed at (A) 10 cm centres (B) 15 cm centres (C) 20 cm centres (D) 25 cm centres

Last Answer : Answer: Option B

Description : The maximum thickness of concrete floor of a cement warehouse, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : (D) 25 cm

Description : If the engineer-in-charge approves, the 10 cm cubes may be used for the work test of concrete provided maximum nominal size of aggregate, does not exceed (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : Answer: Option C

Description : The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : Answer: Option C

Description : The raft slab is projected beyond the outer walls of the structure by (A) 5 to 10 cm (B) 15 to 20 cm (C) 25 to 30 cm (D) 30 to 45 cm

Last Answer : Answer: Option D

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 6 m effective span is 10 kg/cm2 , the share stirrups are provided for a distance from either end where, is (A) 50 cm (B) 100 cm (C) 150 cm (D) 200 cm

Last Answer : Answer: Option C

Description : If depth of slab is 10 cm, width of web 30 cm, depth of web 50 cm, centre to centre distance of beams 3 m, effective span of beams 6 m, the effective flange width of the beam, is (A) 200 cm (B) 300 cm (C) 150 cm (D) 100 cm

Last Answer : Answer: Option C

Description : A standard steel tape of length 30 m and cross-section 15 1.0 mm was standardised at 25°C and at 30 kg pull. While measuring a base line at the same temperature, the pull applied was 40 kg. If the modulus of elasticity of ... (A) - 0.000909 m (B) + 0.0909 m (C) 0.000909 m (D) None of these

Last Answer : (A) - 0.000909 m

Description : A car starts from rest and moves on a straight road with a uniform acceleration of 10 m/s2 for the first 10 s. During the next 10 s, the car move s with the velocity it has attained. What is the total distance covered by the car in 20 s? (a) 500 m (b) 1000 m (c) 1,500 m (d) 2,000 m

Last Answer : Ans:(c)

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

Description : A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff  readings at and were 1.22 and 1.06. With the level set up at , the readings at  and were 1.55 and ... upwards  (B) 0.04 m inclined downwards  (C) 0.04 m inclined upward  (D) None of these

Last Answer : (B) 0.04 m inclined downwards 

Description : Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10,  the sight on the up slope must be less than  (A) 25 cm  (B) 20 m  (C) 45 m  (D) 10 m

Last Answer : (C) 45 m 

Description : The total amount of iodine in the body of an average adult is (A) 10–15 mg (B) 20–25 mg (C) 45–50 mg (D) 75–100 mg MINERAL METABOLISM 199

Last Answer : Answer : C

Description : A hydraulic press has a ram of 15 cm diameter and plunger of 1.5 cm. It is required to lift a weight of 1 tonne. The force required on plunger is equal to (A) 10 kg (B) 100 kg (C) 1000 kg (D) 1 kg

Last Answer : Answer: Option A

Description : Diopter is the power of a lens having a focal length of (A) 25 cm (B) 50 cm (C) 75 cm (D) 100 cm

Last Answer : (D) 100 cm

Description : The spacing between the discs in the gang bolt ranges cm for lighy duty and cm heavy -duty harrows i. 15-25 and 25-30 c) 40-45 and 45-50 ii. 20-30 and 30-40. d) 15-25 and 32-36

Last Answer : 15-25 and 25-30

Description : The original cost of an equipment is Rs.10,000. Its salvage value at the end of its total useful life of five years is Rs. 1,000. Its book value at the end of two years of its useful life (as per straight line method of evaluation ... be (A) Rs. 8,800 (B) Rs. 7,600 (C) Rs. 6,400 (D) Rs. 5,000

Last Answer : (C) Rs. 6,400

Description : If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option B

Description : For M 150 mix concrete, according to I.S. specifications, local bond stress, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Last Answer : Answer: Option B

Description : According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is (A) 5 kg/cm2 (B) 10 kg/cm2 (C) 15 kg/cm2 (D) 20 kg/cm

Last Answer : Answer: Option A

Description : Brick walls are measured in sq. m if the thickness of the wall is (A) 10 cm (B) 15 cm (C) 20 cm (D) None of these

Last Answer : (A) 10 cm

Description : The radius of curvature of the arc of the bubble tube is generally kept (A) 10 m (B) 25 m (C) 50 m (D) 100 m

Last Answer : (D) 100 m

Description : A ship whose hull length is 100 m is to travel at 10 m/sec. For dynamic similarity, at what velocity should a 1:25 model be towed through water? (A) 10 m/sec (B) 25 m/sec (C) 2 m/sec (D) 50 m/sec

Last Answer : Answer: Option C