Which of these has the lowest resistance?

1 Answer

Answer :

b) Copper has the lowest resistance. 

Related questions

Description : What affect does the thickness of a wire have on its resistance?

Last Answer : Ans: The resistance of a wire decreases as its thickness increases.

Description : Name two materials that have a different electric resistance. 

Last Answer : Ans: a) copper, nichrome 

Description : State the procedure for testing of earth pit resistance with necessary diagrams.

Last Answer : Following procedure (Method) for testing of earth pit resistance with necessary diagrams. 1) Earth Tester : i) Three point method ii) Four point method 2) By Potential drop method 3 ... of that earthing pit. In this test the accuracy is less but electrical rods are not required. 

Description : State the impact of inductance and resistance on transmission line performance

Last Answer : Impact of inductance on transmission line: 1) It causes IXL drop in transmission line which affects regulation. 2) It is the only parameter which decides power transmission capacity of line i. ... is very small, it causes losses, temperature rise& poor voltage regulation so it cannot be neglected

Description : What do you mean by exciting resistance and exciting reactance?

Last Answer : At no-load, a transformer behaves as a highly inductive load connected to the system which contains some resistance and inductance in parallel. The resistance is called exciting resistance R0 = V1/I w and reactance is called exciting reactance, X0 = V1/I mag

Description : Resistance

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Last Answer : equivalent resistance

Description : role of the series resistance connected in PMMC movement.

Last Answer : A PMMC Instrument can be used as voltmeter by just connecting a series resistance with the moving coil. This series resistance is called Voltmeter Multiplier. This combination of moving coil and ... current whose voltage is to be measured. Ideally the resistance of voltmeter should be infinite

Description : Define resistance with its unit.

Last Answer : Resistance is a measure of the degree to which a substance impedes the flow of electric current induced by a voltage.  Or Resistance is the opposition to current flow in an electrical circuit. Unit is ohm.(Ω)

Description : List two advantages of platinum resistance thermometer.

Last Answer : 1. The platinum resistance thermometer is stable 2. It is resistant to corrosion 3. It is resistant to oxidation

Description : How does the resistance of a conductor compare to that of an insulator?

Last Answer : The resistance of a conductor can be significantly lower than the resistance of an insulator, depending on each material's atomic properties.

Description : Resistance formula

Last Answer : The formula for resistance is, Where, R = resistance in Ohms ρ = resistivity in ohm - metre l = length A = cross sectional area

Description : Parallel Reactance and Resistance Example 1

Last Answer : Parallel Reactance and Resistance Example 1

Description : AC Circuits with Resistance but No Reactance

Last Answer : AC Circuits with Resistance but No Reactance AC Circuits with Resistance but No Reactance Series resistances let two resistances R 1 and R 2 are connected in series as shows in figure and there ... voltage. Voltage V A is common to both the branch hence voltage V A is common reference.

Description : Problems on resistance and resistivity

Last Answer : Problem on resistance and resistivity 1 : https://youtu.be/OqavD7OlZUs Problem on resistance and resistivity 2 : https://youtu.be/0eo8VO8cpwk Problem on resistance and resistivity 3 : https:// ... https://youtu.be/3neLRCTz0RQ Problem on resistance and resistivity 13 : https://youtu.be/vBCkvPOiztY

Description : Problem on temperature coefficient of resistance 3

Last Answer : Problem on temperature coefficient of resistance 3

Description : Problem on temperature coefficient of resistance 2

Last Answer : Problem on temperature coefficient of resistance 2

Description : Problem on temperature coefficient of resistance 1

Last Answer : Problem on temperature coefficient of resistance 1

Description : Problem on resistance and resistivity 13

Last Answer : Problem on resistance and resistivity 13

Description : Problem on resistance and resistivity 12

Last Answer : Problem on resistance and resistivity 12

Description : Problem on resistance and resistivity 11

Last Answer : Problem on resistance and resistivity 11

Description : Problem on resistance and resistivity 10

Last Answer : Problem on resistance and resistivity 10

Description : Problem on resistance and resistivity 9

Last Answer : Problem on resistance and resistivity 9

Description : Problem on resistance and resistivity 8

Last Answer : Problem on resistance and resistivity 8

Description : Problem on resistance and resistivity 7

Last Answer : Problem on resistance and resistivity 7

Description : Problem on resistance and resistivity 6

Last Answer : Problem on resistance and resistivity 6

Description : Problem on resistance and resistivity 5

Last Answer : Problem on resistance and resistivity 5

Description : Problem on resistance and resistivity 4

Last Answer : Problem on resistance and resistivity 4

Description : Problem on resistance and resistivity 3

Last Answer : Problem on resistance and resistivity 3

Description : Problem on resistance and resistivity 2

Last Answer : Problem on resistance and resistivity 2

Description : Problem on resistance and resistivity 1

Last Answer : Problem on resistance and resistivity 1

Description : Compare between Resistance welding and Arc welding on any six points.

Last Answer : Sr.No Parameters Resistance Welding Arc Welding 1 Type of welding Plastic/Pressure/Non-fusion welding Fusion/Non pressure welding 2 Principle of heat developed Heat ... It is suitable for mass production It is suitable for heavy job, maintenance and repair work

Description : Name two methods for measurement of low, medium and high resistance. Give one advantage and one limitation of V- I method.

Last Answer : Methods for measurement of low resistance:  1. Ammeter voltmeter method  2. Kelvin's bridge method  3. Ohm meter method  4. Potentiometer method  5. Digital/analog multi-meter ... must be infinity for perfectly accurate measurement which is not possible.  2. Connection errors.

Description : Name the method used to measure following resistances:- (i) Low resistance (ii) Medium resistance (iii) Insulation resistance (iv) Earth resistance.

Last Answer : Following are the methods used to measure resistances:-  (i) Low resistance: 1.Voltmeter-Ammeter Method 2. Kelvin's Double bridge Method  (ii) Medium resistance: 1.Voltmeter-Ammeter Method 2. ... of Charge Method  (iv) Earth resistance : 1. Fall of Potential Method 2. Earth tester

Description : Write any two factors on which earth resistance depends.

Last Answer : Factors on which earth resistance depends: (1) The shape and material used for the electrode (2) Depth of the electrode in the ground. (3) The specific resistance of the soil around the electrode (4) Moisture content in the soil. (5) Nature of soil 

Description : State the use of shunt and series resistance used in extension of meter.

Last Answer : Use of shunt and series resistance: i) Use of shunt: To extend the range of Ammeter. ii) Use of series resistance: To extend the range of Voltmeter.

Description : State the range for low and medium resistance.

Last Answer : Low resistances: less than 1 ohm.  Medium resistances: 1 ohm to 0.1 Mega ohm. 

Description : Explain V- I method of measurement of medium resistance. 

Last Answer : In this method, use suitable source, ammeter and voltmeter and connect them as shown in the above diagram. Take reading of voltmeter and ammeter, then value of resistance = R = V/I Ω To minimise the error take 4 to 5 observation for the same resistance and take their average.

Description : Give classification of resistance based on their ranges.

Last Answer : Classification of Resistances Based on Their Ranges: 1) Low resistance: less than 1 ohm. 2) Medium resistance: 1 ohm to 0.1 Mega ohms. 3) High resistance: greater than 0.1 Mega ohms.

Description : Define pinch off voltage and drain resistance of FET.

Last Answer : 1 . Pinch-off Voltage: It is the value of the drain to source voltage VDS at which the drain current ID reaches its constant saturation value. Any further increase in VDS does not have any ... drain to source voltage to the change in drain current. It is also called AC/dynamic drain resistance.

Description : Define the following terms as referred to battery. a) E.M.F b) Internal resistance c) Ah efficiency d) WAh efficiency

Last Answer : a) E.M.F : The electromotive force of a battery is defined as the energy spent or the work done in taking a unit positive charge around the complete circuit of the battery i.e., in ... input required to restore the initial state of charge, under specified conditions, is called Watt-hr efficiency.

Description :  A resistor in which the resistance changes exponentially with change in temperature is called as A) Potentiometer B) Phototransistor C) Varactor D) Thermistor 

Last Answer :  A resistor in which the resistance changes exponentially with change in temperature is called as Thermistor 

Description : If the insulation resistance of a cable of length 10 km is 1 mega ohm, its insulation resistance for 50 km length will be

Last Answer : If the insulation resistance of a cable of length 10 km is 1 mega ohm, its insulation resistance for 50 km length will be 0.2 mega ohm

Description : A 200 V DC machine supplies 20 A at 200 V as a generator. The armature resistance is 0.2 Ohm. If the machine is now operated as a motor at same terminal voltage and current but with the flux increased by 10%, the ratio of motor speed to generator speed is

Last Answer : A 200 V DC machine supplies 20 A at 200 V as a generator. The armature resistance is 0.2 Ohm. If the machine is now operated as a motor at same terminal voltage and current but with the flux increased by 10%, the ratio of motor speed to generator speed is 0.87

Description : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

Last Answer : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

Description : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he

Last Answer : A single phase transformer has resistance and reactance of 0.2 pu and 0.6 pu respectively. Its pu voltage regulation at 0.8 pf lagging would he 0.52

Description : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is

Last Answer : A 200 V dc shunt motor is running at 1000 rpm and drawing a current of 10 A. Its armature winding resistance is 2 Ohm. It. is braked by plugging. The resistance to be connected in series with armature to restrict armature current to 10 A, is 36 Ohm

Description : Arc resistance  (1) increases with increase in arc current (2) decrease with increase in arc current (3) is independent of arc current (4) is independent of arc length

Last Answer : Arc resistance decrease with increase in arc current 

Description : Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  (C) Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

Last Answer : Identify the correct combination of respective Electric arc welding and Electric resistance welding methods :  (A) Butt welding and Seam welding  (B) Hydrogen shielding and Projection welding  ... Seam welding and Coated electrode welding  (D) Coated electrode welding and Hydrogen shielding

Description : Resistance grounding is normally used for :  (A) high voltage long over head transmission lines  (B) low voltage short over head transmission lines  (C) extra high voltage long over head transmission lines  (D) all the above

Last Answer : Resistance grounding is normally used for : low voltage short over head transmission lines