To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the pipe is 1506 m and f = 0.01, ignoring other minor losses and assuming the economical diameter from Lea's formula D = 1.2 Q, the water horse power of the pump is (A) 400 (B) 450 (C) 500(D) 600

To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is 

installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length 

of the pipe is 1506 m and f = 0.01, ignoring other minor losses and assuming the economical 

diameter from Lea's formula D = 1.2 Q, the water horse power of the pump is 

(A) 400 

(B) 450 

(C) 500

(D) 600

by

1 Answer

Answer :

(D) 600

by

Related questions

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

A sewer has a diameter of 300 mm and slop of 1 in 400. While running full it has a mean velocity of 0.7 m/s. If both the diameter and slope are doubled (to respectively be 600 mm and 1 in 200), what will be the changed mean velocity when running half-full? Use Manning’s formula. (a) 1.59 m/s (b) 2.80 m/s (c) 0.90 m/s (d) 1.00 m/s

Description : A sewer has a diameter of 300 mm and slop of 1 in 400. While running full it has a mean velocity of 0.7 m/s. If both the diameter and slope are doubled (to respectively be 600 mm and 1 in 200), what will be the changed mean velocity ... 's formula. (a) 1.59 m/s (b) 2.80 m/s (c) 0.90 m/s (d) 1.00 m/s

Last Answer : (a) 1.59 m/s

The depth of the water table at a place is 45 m below the general ground level. To lift water from a deep tube well in such a locality, the type of pump to be installed is (A) Centrifugal pump (B) Reciprocating pump (C) Deep well turbine pump (D) None of these

Description : The depth of the water table at a place is 45 m below the general ground level. To lift water from a  deep tube well in such a locality, the type of pump to be installed is  (A) Centrifugal pump  (B) Reciprocating pump  (C) Deep well turbine pump  (D) None of these 

Last Answer : (C) Deep well turbine pump

For 3.25 × 10-2 cumecs discharging from a well, a pump is installed to lift water against a total head of 30 m. The minimum required horse power, is (A) 10 H.P. (B) 15 H.P. (C) 18 H.P. (D) 20 H.P.

Description : For 3.25 × 10-2 cumecs discharging from a well, a pump is installed to lift water against a total head  of 30 m. The minimum required horse power, is  (A) 10 H.P.  (B) 15 H.P.  (C) 18 H.P.  (D) 20 H.P. 

Last Answer : (D) 20 H.P. 

For calculation of economical diameter D of a pipe in metres for a discharge Q to be pumped in cumecs, Lea suggested the empirical formula (A) D = 0.22 Q (B) D = 1.22 Q (C) D = 2.22 Q (D) D = 3.22 Q

Description : For calculation of economical diameter D of a pipe in metres for a discharge Q to be pumped in  cumecs, Lea suggested the empirical formula  (A) D = 0.22 Q (B) D = 1.22 Q (C) D = 2.22 Q (D) D = 3.22 Q

Last Answer : (B) D = 1.22 Q

An electric heater draws 5 kW of power for continuous hot water generation in an industry. How much quantity of water in litres per min can be heated from 30oC to 85oC ignoring losses?. a) 1.3 b) 78.18 c) 275 d) none of the above

Description : An electric heater draws 5 kW of power for continuous hot water generation in an industry. How much quantity of water in litres per min can be heated from 30oC to 85oC ignoring losses?. a) 1.3 b) 78.18 c) 275 d) none of the above

Last Answer : a) 1.3

If Q is discharge is cubic metres per sec and D is the economical diameter of the pipe. According to Lea (A) D = 0.67 to 0.87 Q (B) D = 0.77 to 0.97 Q (C) D = 0.97 to 1.22 Q (D) D = 1.22 to 1.33 Q

Description : If Q is discharge is cubic metres per sec and D is the economical diameter of the pipe. According to Lea (A) D = 0.67 to 0.87 Q (B) D = 0.77 to 0.97 Q (C) D = 0.97 to 1.22 Q (D) D = 1.22 to 1.33 Q

Last Answer : (C) D = 0.97 to 1.22 Q

The Brake Horse power of the motor (efficiency 60%) required for a pump of capacity 0.075 cumec for a total lift of 12 m, is A. 10 B. 15 C. 20 D. 25 Q No: 44 Aerobic bacterias A. Flourish in the presence of free oxygen B. Consume organic matter as their food C. Oxidise organic matter in sewage D. All the above

Description : The Brake Horse power of the motor (efficiency 60%) required for a pump of capacity 0.075 cumec for a total lift of 12 m, is A. 10 B. 15 C. 20 D. 25 Q No: 44 Aerobic bacterias A. ... presence of free oxygen B. Consume organic matter as their food C. Oxidise organic matter in sewage D. All the above

Last Answer : ANS: D

P and Q undertake to do a piece of job for Rs.1200. P alone can do it in 12 days while Q alone can do it in 16 days. With the help of R , they finish it in 6 days. Find the share of P,Q & R. a) 400,600,200 b) 200,400,600 c) 450,400,250 d) 600,450,150

Description :  P and Q undertake to do a piece of job for Rs.1200. P alone can do it in 12 days while Q alone can do it in 16 days. With the help of R , they finish it in 6 days. Find the share of P,Q & R. a) 400,600,200 b) 200,400,600 c) 450,400,250 d) 600,450,150

Last Answer : D R;s 1 day work = 1/6 – (1/12 + 1/16) =1/6 – 1/12 – 1/16 = (8-4-3)/48 = 1/48 P:Q:R = ratio of 1 day work = 1/12:1/16 : 1/48 =4:3:1 P’s share = Rs(1200*4/8) =Rs.600 Q’s share = Rs(1200 * 3/8) =Rs.450 R’s share = Rs(1200 * 1/8) =Rs.150

According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Description : According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Last Answer : Answer: Option D

The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit conversion is 20%, then the exit temperature (in k) is (Data: Heat of reaction at 298 K = - 50000 kJ/ kmole of A reacted Heat capacities CPA = CPB = 100kJ/kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Description : The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit ... /kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000

Last Answer : (C) 600

Maximum root zone depth for Maize (a) 200-300 mm (b) 400-600 mm (c) 500-600 mm (d) 350- 450 mm

Description : Maximum root zone depth for Maize (a) 200-300 mm (b) 400-600 mm (c) 500-600 mm (d) 350- 450 mm

Last Answer : (b) 400-600 mm

The rate constant of a chemical reaction increases by 100 times when the temperature is increased from 400 °K to 500 °K. Assuming transition state theory is valid, the value of ‘E/R’ is (A) 8987°K (B) 9210°K (C) 8764°K (D) 8621°K

Description : The rate constant of a chemical reaction increases by 100 times when the temperature is increased from 400 °K to 500 °K. Assuming transition state theory is valid, the value of ‘E/R’ is (A) 8987°K (B) 9210°K (C) 8764°K (D) 8621°K

Last Answer : (B) 9210°K

Sum of tread and rise must lie between (A) 300 to 350 mm (B) 400 to 450 mm (C) 500 to 550 mm (D) 600 to 650 mm

Description : Sum of tread and rise must lie between (A) 300 to 350 mm (B) 400 to 450 mm (C) 500 to 550 mm (D) 600 to 650 mm

Last Answer : Answer: Option B

According to Buston's formula, fire demand in litres per minute for a population of P thousands, is (A) 3182 P (B) 1136.5 [(P/10) + 10] (C) 4637 P (1 - 0.01 P) (D) 5663 P

Description : According to Buston's formula, fire demand in litres per minute for a population of P thousands, is  (A) 3182 P (B) 1136.5 [(P/10) + 10]  (C) 4637 P (1 - 0.01 P)  (D) 5663 P

Last Answer : (D) 5663 P

A certain company employed 600 men and 400 women and the average wage was 2.55 per hour.If a women got 50 paise less than a man, what were their wages per hour ? (a) Man rs 3.00,Woman Rs 2.50 (b) Man Rs 3.50, Woman Rs 3.00 (c) Man Rs 2.75, Woman Rs 2.25 (d) Man Rs 3.25, Woman Rs 2.75

Description : A certain company employed 600 men and 400 women and the average wage was 2.55 per hour.If a women got 50 paise less than a man, what were their wages per hour ? (a) Man rs 3.00,Woman Rs 2.50 (b) Man Rs 3.50, Woman Rs 3.00 (c) Man Rs 2.75, Woman Rs 2.25 (d) Man Rs 3.25, Woman Rs 2.75

Last Answer : Man = Rs 2.75, woman = Rs 2.25

For calculating the evaporation rate over a reservoir surface E = 0.771 (1.465 - 0.00732B) (0.44 - 0.007375 V) (pe - pa), the equation is given by (A) Roohwer's, formula in M.K.S. (B) Roohwer's formula in F.P.S. (C) Dalton's formula in F.P.S. (D) Dalton's formula in M.K.S

Description : For calculating the evaporation rate over a reservoir surface E = 0.771 (1.465 - 0.00732B) (0.44 - 0.007375 V) (pe - pa), the equation is given by (A) Roohwer's, formula in M.K.S. (B) Roohwer's formula in F.P.S. (C) Dalton's formula in F.P.S. (D) Dalton's formula in M.K.S

Last Answer : Answer: Option A

A locomotive of weight 100 tonnes is attached to train of wagons weighing 1000 tonnes. The locomotive pulls the wagons with a constant velocity of 36 km/hour. When the coupling between the train and wagons breaks, the wagons roll on 95 m in 10 sec. The distance between the locomotive and the wagons at this instant assuming that the forces acting on the train are unaltered would be a.0.36 m b.0.44 m c.0.77 m. d.0.5 m e.0.66 m

Description : A locomotive of weight 100 tonnes is attached to train of wagons weighing 1000 tonnes. The locomotive pulls the wagons with a constant velocity of 36 km/hour. When the coupling between the train and wagons breaks, the wagons roll on 95 m in ... would be a.0.36 m b.0.44 m c.0.77 m. d.0.5 m e.0.66 m

Last Answer : d. 0.5 m

Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300

Description : Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300

Last Answer : (C) 350-400

When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the permeability of the soil, is (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Description : When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the ... (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Last Answer : Answer: Option B

n Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 12.20 < 30.5 m a) 300 mm b) 600 mm* c) 500 mm d) 450 mm

Description : n Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 12.20 < 30.5 m a) 300 mm b) 600 mm* c) 500 mm d) 450 mm

Last Answer : b) 600 mm*

In Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 6.10 < 12.2 m a) 300 mm b) 600 mm c) 450 mm* d) 500 mm

Description : In Girder and Slab Bridges Danger level should be marked below bottom of girders/slabs for water way is > 6.10 < 12.2 m a) 300 mm b) 600 mm c) 450 mm* d) 500 mm

Last Answer : c) 450 mm*

Orbital radius of GPS satellites is approximately: (A) 15,200 km (B) 26,600 km (C) 18,400 km (D) 36,000 km

Description : Orbital radius of GPS satellites is approximately: (A) 15,200 km (B) 26,600 km (C) 18,400 km (D) 36,000 km

Last Answer : Answer: Option B

The back staff reading on a B.M. of R.L. 500.000 m is 2.685 m. If foresight reading on a point is 1.345 m, the reduced level of the point, is (A) 502.685 m (B) 501.345 m (C) 501.340 m (D) 504.030 m

Description : The back staff reading on a B.M. of R.L. 500.000 m is 2.685 m. If foresight reading on a point is 1.345 m, the reduced level of the point, is (A) 502.685 m (B) 501.345 m (C) 501.340 m (D) 504.030 m

Last Answer : (C) 501.340 m

An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm

Last Answer : Answer: Option A

The cost of the earthwork in excavation for the surface drain of cross-section shown in the given figure for a total length of 5 metres @ Rs. 450% cum, is (A) Rs. 400 (B) Rs. 425 (C) Rs. 450 (D) Rs. 500

Description : The cost of the earthwork in excavation for the surface drain of cross-section shown in the given figure for a total length of 5 metres @ Rs. 450% cum, is (A) Rs. 400 (B) Rs. 425 (C) Rs. 450 (D) Rs. 500

Last Answer : (C) Rs. 450

Standard quantity of material per unit 5KG. Standard Price Rs 5 per KG. actual number of units 400 units. Actual quantity 2,200KG and price of material Rs 4.80 per kg. Calculate material price. a) 100(F) b) 500(A) c) 440(F) d) 600(F)

Description : Standard quantity of material per unit 5KG. Standard Price Rs 5 per KG. actual number of units 400 units. Actual quantity 2,200KG and price of material Rs 4.80 per kg. Calculate material price. a) 100(F) b) 500(A) c) 440(F) d) 600(F)

Last Answer : The standard quantity of material per unit is 5KG, so the standard quantity for 400 units would be: Standard quantity = 5KG/unit x 400 units = 2000KG The standard price per KG is Rs 5, so the ... material cost was lower than the standard material cost. Option (c) is the correct answer: 440(F).

Determine the maximum length of the cable (in km) for transmitting data at a rate of 500 Mbps in an Ethernet LAN with frames of size 10,000 bits. Assume the signal speed in the cable to be 2,00,000 km/s.b. 2 c. 2.5 d. 5

Description : Determine the maximum length of the cable (in km) for transmitting data at a rate of 500 Mbps in an Ethernet LAN with frames of size 10,000 bits. Assume the signal speed in the cable to be 2,00,000 km/s. b. 2 c. 2.5 d. 5

Last Answer : b. 2

A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Description : A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one- ... beam, the number of shear stirrups required, is (A) 30 (B) 35 (C) 40 (D) 45

Last Answer : Answer: Option C

The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channelcapacity. Assuming that processing delay is negligible, the minimum number of bits for the sequence number field in a frame for maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Description : The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channel capacity. Assuming that processing ... maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Last Answer : c. C

135 litres of water per person per day, is provided in (A) Nurses homes (B) Hostels (C) Residential schools (D) All the above

Description : 135 litres of water per person per day, is provided in (A) Nurses homes (B) Hostels (C) Residential schools (D) All the above

Last Answer : (D) All the above

According to IS : 1172-1963, a minimum of 135 litres of water capita per day, is required for (A) Boarding schools (B) Nurses home and medical quarters (C) Hostels (D) All the above

Description : According to IS : 1172-1963, a minimum of 135 litres of water capita per day, is required for (A) Boarding schools (B) Nurses home and medical quarters (C) Hostels (D) All the above

Last Answer : (D) All the above

As per IS : 1172-1963, water required per head per day for average domestic purposes, is (A) 50 litres (B) 65 litres (C) 85 litres (D) 135 litres

Description : As per IS : 1172-1963, water required per head per day for average domestic purposes, is  (A) 50 litres  (B) 65 litres  (C) 85 litres  (D) 135 litres

Last Answer : (D) 135 litres

If h is the loss due to friction in a pipe. Total losses in strainer and bends may be taken as (A) 0.01 h (B) 0.45 h (C) 0.20 h (D) 0.25 h

Description : If h is the loss due to friction in a pipe. Total losses in strainer and bends may be taken as (A) 0.01 h (B) 0.45 h (C) 0.20 h (D) 0.25 h

Last Answer : Answer: Option D

If w is the weight of water per cubic metre, Q is the discharge in cubic metres per sec and H is the total head, the required water horse power of the pump, is (A) wQH/15 (B) wQH/360 (C) wQH/220 (D) wQH/550

Description : If w is the weight of water per cubic metre, Q is the discharge in cubic metres per sec and H is the total head, the required water horse power of the pump, is (A) wQH/15 (B) wQH/360 (C) wQH/220 (D) wQH/550

Last Answer : (A) wQH/15

A cistern is filled in 15 hours by three pipes P, Q and R. The pipe R is thrice as fast as Q and Q is thrice as fast as P. How much time will pipe P alone take to fill the tank? A) 120 hrs B) 195 hrs C) 135 hrs D) Cannot be determined

Description : A cistern is filled in 15 hours by three pipes P, Q and R. The pipe R is thrice as fast as Q and Q is thrice as fast as P. How much time will pipe P alone take to fill the tank? A) 120 hrs B) 195 hrs C) 135 hrs D) Cannot be determined 

Last Answer : B Suppose pipe P alone takes x hours to fill the tank. Then, pipes Q and R will take x/3 and x/9hours respectively to fill the tank. 1/x + 3/x + 9/x = 1/15 13/x = 1/15 => x = 195 hrs.

The average domestic consumption under normal conditions in an Indian city per day per person, is (A) 105 litres (B) 115 litres (C) 125 litres (D) 135 litres

Description : The average domestic consumption under normal conditions in an Indian city per day per person,  is  (A) 105 litres  (B) 115 litres  (C) 125 litres  (D) 135 litres

Last Answer : (D) 135 litres

If P is population of a city in thousands and Q is fire demand in litres per minute, for proper estimate of water, the Empirical formula Q = 1135 [(P/5) + 10] is suggested by (A) National Board of fire under-writers (B) Freeman (C) Kuichling (D) None of these

Description : If P is population of a city in thousands and Q is fire demand in litres per minute, for proper  estimate of water, the Empirical formula Q = 1135 [(P/5) + 10] is suggested by  (A) National Board of fire under-writers  (B) Freeman  (C) Kuichling  (D) None of these 

Last Answer : (B) Freeman 

A vibrating machine of 100 kg is mounted on a rubber pad which has stiffness of 500 N/m. Determine force transmitted to the foundation if the unbalanced force 500 N acts on it. The frequency ratio (ω/ω n ) is 1.5 and ξ = 0.5 A. 461.62 N B. 400.23 N C. 450 N D. Insufficient data

Description : A vibrating machine of 100 kg is mounted on a rubber pad which has stiffness of 500 N/m. Determine force transmitted to the foundation if the unbalanced force 500 N acts on it. The frequency ratio (ω/ω n ) is 1.5 and ξ = 0.5 A. 461.62 N B. 400.23 N C. 450 N D. Insufficient data

Last Answer : A. 461.62 N

The diameter of a domestic sewer pipe laid at gradient 1 in 100 is recommended (A) 100 mm (B) 150 mm (C) 200 mm (D) 175 mm

Description : The diameter of a domestic sewer pipe laid at gradient 1 in 100 is recommended (A) 100 mm (B) 150 mm (C) 200 mm (D) 175 mm

Last Answer : (B) 150 mm

If discharge of a pump is 0.16 cumecs, the economic diameter of pipe, is (A) 0.488 m (B) 4.88 cm (C) 48.8 cm (D) 4.88 m

Description : If discharge of a pump is 0.16 cumecs, the economic diameter of pipe, is  (A) 0.488 m  (B) 4.88 cm  (C) 48.8 cm  (D) 4.88 m 

Last Answer : (A) 0.488 m 

If the average daily demand of a city of 50,000 population, is 20 m.l.d., the maximum daily demand is (A) 24 mld (B) 30 mld (C) 36 mld (D) 54 mld

Description : If the average daily demand of a city of 50,000 population, is 20 m.l.d., the maximum daily demand is (A) 24 mld (B) 30 mld (C) 36 mld (D) 54 mld

Last Answer : (C) 36 mld

If the viscosity of ground water is 1.00, the Slitcher's constant is 400, the effective size of soil particles in aquifer is 0.5 mm and hydraulic gradient is 1 in 80, the velocity of flow is (A) 0.25 m/day (B) 0.50 m/day (C) 1.00 m/day (D) 1.25 m/day

Description : If the viscosity of ground water is 1.00, the Slitcher's constant is 400, the effective size of soil particles in aquifer is 0.5 mm and hydraulic gradient is 1 in 80, the velocity of flow is (A) 0.25 m/day (B) 0.50 m/day (C) 1.00 m/day (D) 1.25 m/day

Last Answer : Answer: Option D

The original cost of an equipment is Rs.10,000. Its salvage value at the end of its total useful life of five years is Rs. 1,000. Its book value at the end of two years of its useful life (as per straight line method of evaluation of depreciation) will be (A) Rs. 8,800 (B) Rs. 7,600 (C) Rs. 6,400 (D) Rs. 5,000

Description : The original cost of an equipment is Rs.10,000. Its salvage value at the end of its total useful life of five years is Rs. 1,000. Its book value at the end of two years of its useful life (as per straight line method of evaluation ... be (A) Rs. 8,800 (B) Rs. 7,600 (C) Rs. 6,400 (D) Rs. 5,000

Last Answer : (C) Rs. 6,400

Question No. 216 If the specific capacity of a well is 0.3183 × 10-3 per sec, the discharge from a well of 4 m diameter under a depression head of 4 m, is (A) 8 litres/sec (B) 10 litres/sec (C) 12 litres/sec (D) 16 litres/sec

Description : Question No. 216 If the specific capacity of a well is 0.3183 × 10-3 per sec, the discharge from a well of 4 m diameter under a depression head of 4 m, is (A) 8 litres/sec (B) 10 litres/sec (C) 12 litres/sec (D) 16 litres/sec

Last Answer : (D) 16 litres/sec

A vessel is equipped with two ship's service generators. Generator #1 is rated at 900 kw and generator #2 is rated at 600 kw. During parallel operation, with a hotel load of 1,000 kw, what should be the kw load on generator #2? A. 100 kw B. 400 kw C. 500 kw D. 600 kw

Description : A vessel is equipped with two ship's service generators. Generator #1 is rated at 900 kw and generator #2 is rated at 600 kw. During parallel operation, with a hotel load of 1,000 kw, what should be the kw load on generator #2? A. 100 kw B. 400 kw C. 500 kw D. 600 kw

Last Answer : Answer: B

Maintain 850 OC for 1 hour (soaking time).  Cool the material to 60 OC in 4 hours. a) Calculate the efficiency of the furnace, if the specific heat of steel is 0.12 kcal/kgOC and fuel oil consumption per batch is 1400 litres.  GCV of fuel oil - 10200 kcal/kg,  Cost of fuel oil - Rs. 46,000/kL,  Sp. gr. of fuel oil - 0.92. b) Due to high cost of oil, the plant management decides to convert to a lower operating cost LPG fired furnace lined on the inside with ceramic fibre insulation and with an operating efficiency of 80%, for same requirement. The investment towards installation of the new furnace is Rs. 50 lakhs. Calculate the Return on Investment, if the plant operates two batches per day and 250 days in a year.  Cost of LPG - Rs. 75/kg,  GCV of LPG - 12500 kcal/kg.

Description : In a heat treatment shop, steel components are heat-treated in batches of 80 Tons. The  heat treatment cycle is as follows;  Increase temperature from 30 OC to 850 OC in 3 hours.  ... efficiency of 80%, for same requirement. The investment towards installation of  the new furnace is Rs. 50

Last Answer : Quantity of steel treated per batch - 80 Tons a. Efficiency of Furnace: Useful heat supplied to steel - 80000 x 0.12 x (850 - 30)   = 7872000 kcal/batch .1 mark Total heat ... = Rs. 64400/batch Efficiency of new LPG furnace - 80% Heat supplied in new LPG furnace - 7872000/0.8

As per the Constitution of India, what is the limit prescribed for the number of members in the Legislative Assembly of a State? (1) 350 members (2) 400 members (3) 450 members (4) 500 members

Description : As per the Constitution of India, what is the limit prescribed for the number of members in the Legislative Assembly of a State? (1) 350 members (2) 400 members (3) 450 members (4) 500 members

Last Answer : (4) 500 members Explanation: The number of members ranges between 60 and 500.

If the chosen diameter of a pipe, is less than the economical diameter (A) Cost of pipe will be less (B) Head loss will be high (C) Cost of pumping will be more than saving (D) All the above

Description : If the chosen diameter of a pipe, is less than the economical diameter  (A) Cost of pipe will be less  (B) Head loss will be high  (C) Cost of pumping will be more than saving  (D) All the above

Last Answer : (D) All the above

A round viewing window with a 20 centimeter diameter is installed in a tank at the Shedd Aquarium. It is 5 meters below the water surface. The force on the window is approximately: w) 1,500 Newtons x) 10,000 Newtons y) 25,000 Newtons z) 50,000 Newtons

Description : A round viewing window with a 20 centimeter diameter is installed in a tank at the Shedd Aquarium. It is 5 meters below the water surface. The force on the window is approximately: w) 1,500 Newtons x) 10,000 Newtons y) 25,000 Newtons z) 50,000 Newtons

Last Answer : ANSWER: W -- 1,500 NEWTONS