State two factors deciding size of conduit.

1 Answer

Answer :

Following factors deciding size of conduit: 1) Types of wiring method 2) No. of wires carried out through conduit 3) Size of wires required for sub circuits which is carried out through conduit 4) Future expansion.

Related questions

Description : State function of i) Ceiling rose ii) Conduit 

Last Answer : Function of Ceiling rose: Output connection for ceiling fan or tube.  Function of Conduit – To run the wires from switch board to appliances. 

Description : State I.E. Rule No.90 

Last Answer : I.E. Rule No.90: All metal supports of overhead lines and metallic fittings attached there to, shall be permanently and effectively earthed. For this purpose, a continuous earth wire shall be provided and ... one insulator has been placed in at a height not less than 3.3 m from the ground.

Description : Define Tender and state any three requirements of valid contract.

Last Answer : Meaning Tender:- Tender is offer or invitation of the work between any two parties. This offer may be written or non written. This offer is given by party no.1 (owner) to party no.2 ( ... . Contract should be signed by proper authorized persons. 6. It should be legally challenged in the court.

Description : Define contract and state its types.

Last Answer : Definition of Contract:- The agreement between two parties under some specific terms and conditions is known as contract.  Types of Engineering contract:- 1) Lump sum contract 2) Item rate contract 3) ... contract 11)Cost plus(+) fluctuating fees rate contract 12) Cost plus(+) fix fee contract 

Description : Define service connection and state types connection and state types of overhead service connection

Last Answer : Service Connection:- It is the input conductor or wire which is carried out from supply company (authorities) pole to consumers' main board or premises. Types of overhead service ...  1. Overhead service connection with Bare conductor 2. Overhead service connection with weather proof cable  

Description : State the various factors governing selection of site for TPS. 

Last Answer : Following various factors governing selection of site for TPS.:- 1. It should locate near coal mines. 2. Sufficient quantity of water should be available. 3. Sufficient large space should ... availalbe nearly. To the extent possible, the thermal station should be far away from an aerodrome   

Description : State and explain any four factors governing selection of induction motor.

Last Answer : The factors governing the selection of Induction motor: 1) Load torque required at normal speed matches with available torque of motor. 2) Break down torque or pull out torque or maximum torque ... If selecting energy efficient motor the cost benefit analysis over the long run must be worked out.

Description : State any four factors for selection of hydro power plant site. 

Last Answer : Following Factors to be kept while site selecting for Hydro power plant: 1) Quantity of water available :-Where high rainfall occures so that sufficent quantity of water can be stored for generation of ... be possible to divert the stream. 11. Sand, gravel, etc., should be available nearby.

Description : State any four factors for selection of site of wind power plant.

Last Answer : The Factors for selection of site for Wind Mills: 1) The site should be selected where winds are strong i.e. where pressure of wind is high and there is continuity (14.4- 16.2 km/h) ... 50m of the turbine which can affect the system's overall performance 10)Possibility to connect to power grid. 

Description : State any four factors for selecting location of nuclear power plant.

Last Answer : i) Seismicity: If the area of a nuclear site is seismically active, it may not be used for nuclear power plant.  ii) Water Availability: The nuclear power plants would need a ... Therefore, the site selected for such plant should have adequate arrangement for the disposal of radioactive waste.

Description : State any four factors governing Selection of site for thermal power station. 

Last Answer : Following Factors are to be considered:- 1. It should locate near coal mine. 2. Sufficient quantity of water should be available. 3. Sufficient large space should be available. 4. It should be located ... laws of the land and the town planning. 14. The interests of national defense must be served.

Description : State the factors affecting hysteresis loss.

Last Answer : i) Flux density ii) Frequency iii) Volume of the magnetic material iv) Nature of magnetic material

Description : Write any two factors on which earth resistance depends.

Last Answer : Factors on which earth resistance depends: (1) The shape and material used for the electrode (2) Depth of the electrode in the ground. (3) The specific resistance of the soil around the electrode (4) Moisture content in the soil. (5) Nature of soil 

Description : List out factors affecting proximity effect. 

Last Answer : Factors affecting proximity effect: 1. Conductor size (diameter of conductor) 2. Frequency of supply current. 3. Distance between conductors. 4. Permeability of conductor material 

Description : The main disadvantages of having poor power factors are:  (A) High cost of station and distribution equipment (B) Poor voltage regulation (C) High energy loss in conductor (D) All of the above

Last Answer : The main disadvantages of having poor power factors are:  (A) High cost of station and distribution equipment (B) Poor voltage regulation (C) High energy loss in conductor (D) All of the above

Description : What are the factors influencing measurement errors?

Last Answer : The factor influencing measurement errors are accuracy, precision, range and bandwidth, sensitivity, resolution and uncertainty.

Description : The Semiconductor strain gauges typically have much higher gauge factors than those of metallic strain gauges, primarily due to : (A) higher temperature sensitivity (B) higher Poisson’s ratio (C) higher piezoresitive coefficient (D) higher magnetostrictive coefficient

Last Answer : The Semiconductor strain gauges typically have much higher gauge factors than those of metallic strain gauges, primarily due to : higher piezoresitive coefficient

Description : What factors affect resistivity?

Last Answer : 1)type of material 2)temperature 3)length and area of cross section of conductor

Description : Does size matter?

Last Answer : In sports, sure it can matter. But you have to be athletic too.

Description : Is size 14 fat?

Last Answer : Not necessarily.

Description : How to Size a Helmet

Last Answer : How to Size a Helmet A helmet that fits you right will save you a lot of headaches in the future. Nothing ruins a good run in your motorcycle, race car or anything similar than an ill-fitting ... go. Having a loose chinstrap can cause your helmet to fly away, exposing you and others to danger.

Description : How to Find Your Hat Size ?

Last Answer : How to Find Your Hat Size Hats are great fashion accessories, but if you insist on wearing ones that don't fit you, then it's not quite as great. Here's how to ensure that every hat you purchase ... a brand with sizes that fit you, you now have a source of fine-fitting hats whenever you need them.

Description : Which bed size is right for you?

Last Answer : Which bed size is right for you? At first glance, the bed seems to be a simple and unpretentious device, but its selection is a rather responsible event. First of all, this concerns issues ... lengthen the frame, which affects the consumption of materials and, accordingly, the cost of the product.

Description : What is the choice of size and number of generator units in interconnected power system?

Last Answer : Choice of Size and Number of Generating Units: 1. The size/rating and number of generating units in such way that they approximately match with the load curve as closely as possible. 2. In ... , if power plant is connected to grid system then generating unit of higher capacity can be installed.

Description : Calculate the size of memory address space for a 16 bit data and 20 bit address bus. A) 1 MB B) 2 MB C) 3 MB D) 4 MB

Last Answer : Calculate the size of memory address space for a 16 bit data and 20 bit address bus. A) 1 MB B) 2 MB C) 3 MB D) 4 MB

Description : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

Last Answer : What is the size of memory which can be accessed by direct accessing in 8085 microprocessor? A) 64 kB B) 4 kB C) 128 kB D) 128 MB 

Description : For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is

Last Answer : For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is 25 x 25

Last Answer :  The size of a synchronous motor decreases with the increase in flux density.

Description : The size of a transformer core will depend on?

Last Answer : The size of a transformer core will depend on frequency and area of the core.

Description : State factors deciding size of busbar chamber for commercial installation.

Last Answer : Size of busbar chamber depends on following factors.  Total load or load current on installation Future load on installation No. of tappings provided on buabar Spare feeders provided if any ... . Incoming and outgoing wires or cables are connected to bus-bar by screw and nut arrangement. 

Description : State any two advantages of MCB over Fuse. State the standard specifications of MCB available in the market.  

Last Answer : Following advantages of MCB over Fuse: 1. No need of replacement of fuse wire. 2. Manually restore of supply is simple. 3. Fault understanding by visual inspection 4. More safe than fuse The standard specifications of ... 6A, 10A,16A,20A, 25A, 30A, 32A, 40A, 50A, 60A and 63A 6. 250V and 450 v

Description : State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material. 

Last Answer :  (i) Application of PVC paper : 1. It is used in slot lining or motor winding insulation purpose 2. For Insulation of Transformer winding (ii) Application of Porcelain : 1. Mainly used for manufacturing ... on withstand temperature : * H' & C' Class of insulation i e. 180° and above 180°C 

Description : State two types of Electronic dimmer.

Last Answer : Two types of electronic dimmers are: 1) S.C.R. operated dimmer 2) Triac operated dimmer 

Description : What advantage would there be in making DC a state?

Last Answer : For whom? The people who live there, or everyone else?

Description : What do you think the worst state is?

Last Answer : Alabama

Description : State jumping operation.

Last Answer : Jumping up operation: This process makes metal shorter and thicker and carried out at near welding temperature. Metal can be either thickened at the ends of bars or swollen in the center.

Description : State the procedure for testing of earth pit resistance with necessary diagrams.

Last Answer : Following procedure (Method) for testing of earth pit resistance with necessary diagrams. 1) Earth Tester : i) Three point method ii) Four point method 2) By Potential drop method 3 ... of that earthing pit. In this test the accuracy is less but electrical rods are not required. 

Description : State the procedure for laying / installation of underground cable.  

Last Answer : 1) Direct laying Cable: or Trench laying method: Procedure: * For laying of a cable trench about 1.5m deep and 0.5m wide is made along the cable route. * A ... over. * Cables laid in this manner are usually plain lead covered because troughing affords good mechanical protection. 

Description : State the insulating materials used in motor. Write temperature class and withstand temperature ranges for them. 

Last Answer : The insulating materials used in motor are as belows: 1. Cotton, 2. Silk, or paper, 3. Press board, 4. Resins 5. PVC 6. Cellulose-Fiber, 7. Enameled coating, etc  ... Over 180° Mica, porcelain, ceramics, glass quartz, asbestos, treated glass fiber or treated asbestos. etc.

Description : State any Four lE Rules regarding electric safety. 

Last Answer :  lE Rules regarding electric safety: 1. IE Rule 3 : Authorization 2. IE Rule 29 : Construction and maintenance of electrical supply line and apparatus 3. IE Rule 30: Service line and apparatus on ... 26. IE Rule 60: Test for resistance of insulation 27. IE Rule 61: Connection with earth 

Description : Define earthing. State its types.  

Last Answer : Definition of earthing: * Earthing means connecting the metal body of electrical device to the general mass of earth by a wire of negligible resistance. OR * Earthing means connecting the metal body of ... ii) Pipe type earthing iii) Rod type earthing iv) Strip earthing v)Water main earthing

Description : State the type of insulating materials under Class Y and Class B.

Last Answer : The type of insulating materials under Class Y : 1. Cotton  2. Silk 3. Paper 4. Rubber 5. PVC The type of insulating materials under Class B: 1. Backelite 2. Impregnated varnish 3. Mica 4. Fiber glass 5. Asbestos 

Description : State gaseous and liquid insulating material.

Last Answer : i) Gaseous insulating material : 1. Air 2. Nitrogen 3. Hydrogen 4. SF6 ii) liquid insulating material: 1. Transformer oil 2. Capacitor oil 3. Cable oil 4. Pyranol 5. Savotal 6. Savol 7. Vegetable oil 8. Silicon liquids

Description : State the material used for making (1) Magnetic Core (2) Fuse element  

Last Answer : The material used for making of:  (1) Magnetic Core : Iron, cobalt, Nickel, CRGO, HRGO , silicon steel  (2) Fuse Element: Tin- lead wire, Tinned copper wire 

Description : State the types of protections provided by MCB. 

Last Answer : The types of protections provided by MCB: 1. MCB provides short circuit protection. 2. MCB provides overload protection

Description : State different types of holders used in wiring installation.

Last Answer : Following types of holders used in wiring installation: 1. Pendent Holder 2. Batten Holder 3. Angle holder 4. Screwed holder 

Description : State the applications of TIG welding.

Last Answer : The applications of TIG welding are as follows: 1. Mostly used to weld aluminum and aluminum alloys. 2. It is used to weld stainless steel, carbon base alloy, copper base alloy, nickel base alloy etc. 3. It is used to welding dissimilar metals. 4. It is mostly used in aerospace industries.

Description : State the applications of rolling.

Last Answer : Applications of rolling are as follows: 1. Concrete reinforcing bars. 2. Plates. 3. Wire rods. 4. Sheet and strip. 5. Rails. 6. Piping and tubes. 7. Body panels. 8. Construction materials

Description : State the modification to be done in dc series motor to work satisfactorily as ac series motor. State applications of ac series motor.

Last Answer : Modifications are necessary in a dc series motor so that it operates satisfactorily on ac supply. The modifications are as follows:  1) AC series motor is built with a few field turns as ... and grinders 5) High speed vacuum cleaners 6) Sewing machines 7) Food processors 8) Drilling machine 

Description : State advantages of rotating field type alternators. 

Last Answer : Advantages of Rotating Field Type Alternator: 1) For high-voltage alternator, large space is required to accommodate conductors with insulation, as high voltage is induced in them. If field poles are placed ... is kept rotating. 8) Rotating field is comparatively light and can run with high speed.