A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?
by

1 Answer

Answer :

The current is 10.0A.  1ampere = 1 Coulomb per 1 second.  0.1Coulombs ÷ 0.01seconds = 10.0amperes.
by

Related questions

What is the smallest unit of a compound with the same chemical characteristics?

Description : What is the smallest unit of a compound with the same chemical characteristics?

Last Answer : The molecule is the smallest unit of a compound with the same chemical characteristics.

How does the resistance of a conductor compare to that of an insulator?

Description : How does the resistance of a conductor compare to that of an insulator?

Last Answer : The resistance of a conductor can be significantly lower than the resistance of an insulator, depending on each material's atomic properties.

Is the power line voltage available in our homes a dc or an ac voltage?

Description : Is the power line voltage available in our homes a dc or an ac voltage?

Last Answer : The power line voltage available in our homes is AC. Mobile dwellings are the most commonly DC-supplied homes and even then they tend to include AC supply for heavier loads.

What is the function of an electrical filter ?

Description : What is the function of an electrical filter ?

Last Answer : Filter separates different components that are mixed together. Electrical filter can separate different frequency components. Electrical filters are the electrical circuits which are use to remove unwanted frequency components from the signal.

List the main parts of D.C. motor

Description : List the main parts of D.C. motor

Last Answer : Main parts of D.C. motor and their functions:  Part Functions Yoke i) Provides mechanical support for poles. ii) Acts as protecting cover for machine. iii) Carries magnetic flux. ... a fixed physical position relative to the stator.  Shaft Used to transfer mechanical power 

State the principle of operation of d.c. motor.

Description : State the principle of operation of d.c. motor.

Last Answer : When a current carrying conductor is placed in a magnetic field, the conductor experiences the force. The magnitude of force is given by F = BIL newton  where F – Force   B – maximum flux density   I – Current   L – Length of conductor

What is earthing? Give the importance of earthing.

Description : What is earthing? Give the importance of earthing.

Last Answer : Meaning of earthing: Connecting the metallic frame of the electrical machines /any electrical equipment body etc. to ground by using wire/conductor is known as earthing.  Importance of Earthing:  ... currents. 5. To provide stable platform for operation of sensitive electronic equipment's. 

With a neat sketch give the working of shaded pole induction motor.

Description : With a neat sketch give the working of shaded pole induction motor.

Last Answer : Explanation: It has squirrel cage rotor and salient pole stator. The stator poles are shaded partially by short circuited conductor band to create the phase difference between the fluxes emerging from shaded ... rotating magnetic field in the air-gap and torque is exerted on the squirrel cage rotor.

Why does the speed of a DC shunt motor decrease as the load increases?

Description : Why does the speed of a DC shunt motor decrease as the load increases?

Last Answer : Because if the load is increasing then the torque must also be increase. If not then the speed of motor will decrease.

Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced. 

With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Description : With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Last Answer : Working of N channel FET: * When a voltage is applied between the drain and source with a DC supply (VDD), the electrons flows from source to drain through narrow channel ... where the channel gets completely blocked and the drain current becomes zero is called pinch- off voltage. 

Illustrate with neat wiring diagram a single lamp control by two point method.

Description : Illustrate with neat wiring diagram a single lamp control by two point method.

Last Answer : Single lamp control by two point method:  This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the ... the person will change the position of switch S2, so that the lamp will be switched OFF'.

Which is a semiconductor: copper, silicon, or neon?

Description : Which is a semiconductor: copper, silicon, or neon?

Last Answer : Copper is a metal. Silicon is a semiconductor. Neon is inert gas.

In a metal conductor, what is a free electron?

Description : In a metal conductor, what is a free electron?

Last Answer :  When many atoms are close together in a copper wire, the outermost orbital electron of each copper atom can easily break free from its home or parent atom. These electrons then can migrate easily ... random. Such electrons that can move freely from one atom to the next are called free electrons.

What is PLL? Explain its operation with a block diagram.

Description : What is PLL? Explain its operation with a block diagram.

Last Answer : PLL - A phase-locked loop or phase lock loop is a control system that generates an output signal whose phase is related to the phase of an input signal Block diagram  ... to the input frequency. The phase - locked loop goes through three states free running capture and phase lock.

The operating point of a protective current transformer is near the

Description : The operating point of a protective current transformer is near the

Last Answer : The operating point of a protective current transformer is near the Ankle point

If the % reactance upto the fault point is 20%, then the short circuit current will be

Description : If the % reactance upto the fault point is 20%, then the short circuit current will be

Last Answer : If the % reactance upto the fault point is 20%, then the short circuit current will be 5 times the full load current

State the material used for making (1) Magnetic Core (2) Fuse element

Description : State the material used for making (1) Magnetic Core (2) Fuse element  

Last Answer : The material used for making of:  (1) Magnetic Core : Iron, cobalt, Nickel, CRGO, HRGO , silicon steel  (2) Fuse Element: Tin- lead wire, Tinned copper wire 

Which is the best conductor: silver, carbon, or iron?

Description : Which is the best conductor: silver, carbon, or iron?

Last Answer : Silver is the best conductor. Carbon is the semiconductor. Iron have less conductance as compared to silver.

Problem on temperature coefficient of resistance 1

Description : Problem on temperature coefficient of resistance 1

Last Answer : Problem on temperature coefficient of resistance 1

How do you find power in a circuit?

Description : How do you find power in a circuit?

Last Answer : Power can be find in a circuit by the means of meters .if an individual want to check for a power in a circuit he/she Calabria the meters on a high voltage range and put the meters Lee in parallel with the circuit he /she will know the amount of power within that circuit .

Describe the difference between an open circuit and a short circuit.

Description : Describe the difference between an open circuit and a short circuit.

Last Answer : Open circuit means the wire is cut meaning power will not flow and close circuit means wire is not cut and hence power will flow.Short circuit is the same as close circuit

State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material.

Description : State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material. 

Last Answer :  (i) Application of PVC paper : 1. It is used in slot lining or motor winding insulation purpose 2. For Insulation of Transformer winding (ii) Application of Porcelain : 1. Mainly used for manufacturing ... on withstand temperature : * H' & C' Class of insulation i e. 180° and above 180°C 

Instantaneous value of a sine wave voltage

Description : Instantaneous value of a sine wave voltage

Last Answer : Instantaneous value of a sine wave voltage

Write two applications of D.C. series motor.

Description : Write two applications of D.C. series motor. 

Last Answer : The applications of D.C. series motor: 1. Cranes 2. Hoists 3. Trolley and cars 4. Conveyors 5. For traction work i.e. electric locomotives 6. Elevator 7. Air compressor

A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Description : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Last Answer : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

The loop equation for a series RLC circuit gives

Description : The loop equation for a series RLC circuit gives

Last Answer : The loop equation for a series RLC circuit gives

Source transformation Replace the circuit with voltage source in series with a single resistor

Description : Source transformation Replace the circuit with voltage source in series with a single resistor

Last Answer : Source transformation Replace the circuit with voltage source in series with a single resistor

Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Description : Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Last Answer : Operation:  The FM signal which is to be demodulated is applied at the input of the PLL.  the PLL is locked to the FM  The error voltage produced at ... using PLL ensures a high Linearity, between the instantaneous input frequency and VCO control voltage (error amplifier output)

How to find total impedance Z, current I and Impedance angle ?

Description : How to find total impedance Z, current I and Impedance angle ?

Last Answer : How to find total impedance Z, current I and Impedance angle ?

State the procedure for testing of earth pit resistance with necessary diagrams.

Description : State the procedure for testing of earth pit resistance with necessary diagrams.

Last Answer : Following procedure (Method) for testing of earth pit resistance with necessary diagrams. 1) Earth Tester : i) Three point method ii) Four point method 2) By Potential drop method 3 ... of that earthing pit. In this test the accuracy is less but electrical rods are not required. 

State the procedure for laying / installation of underground cable.

Description : State the procedure for laying / installation of underground cable.  

Last Answer : 1) Direct laying Cable: or Trench laying method: Procedure: * For laying of a cable trench about 1.5m deep and 0.5m wide is made along the cable route. * A ... over. * Cables laid in this manner are usually plain lead covered because troughing affords good mechanical protection. 

State any two advantages of MCB over Fuse. State the standard specifications of MCB available in the market.

Description : State any two advantages of MCB over Fuse. State the standard specifications of MCB available in the market.  

Last Answer : Following advantages of MCB over Fuse: 1. No need of replacement of fuse wire. 2. Manually restore of supply is simple. 3. Fault understanding by visual inspection 4. More safe than fuse The standard specifications of ... 6A, 10A,16A,20A, 25A, 30A, 32A, 40A, 50A, 60A and 63A 6. 250V and 450 v

Explain the suitability of aluminium as an electrical conductor with respect to its mechanical and electrical properties.

Description : Explain the suitability of aluminium as an electrical conductor with respect to its mechanical and electrical properties. 

Last Answer : Following are requirements of conductor:- i) High conductivity :  Material should have high conductivity, So that * cross section of conductor (size) reduces, * Copper losses reduces, * So Efficiency ... . Boiling point is 1820°C 9. Specific gravity is 2.7 10. High resistance to corrosion. 

State the type of insulating materials under Class Y and Class B.

Description : State the type of insulating materials under Class Y and Class B.

Last Answer : The type of insulating materials under Class Y : 1. Cotton  2. Silk 3. Paper 4. Rubber 5. PVC The type of insulating materials under Class B: 1. Backelite 2. Impregnated varnish 3. Mica 4. Fiber glass 5. Asbestos 

State the types of protections provided by MCB.

Description : State the types of protections provided by MCB. 

Last Answer : The types of protections provided by MCB: 1. MCB provides short circuit protection. 2. MCB provides overload protection

State the classification of distribution substation.

Description : State the classification of distribution substation. 

Last Answer : The classification of distribution substation. 1. Pole mounted distribution substation 2. Plinth mounted distribution substation 3. Compact/prefabricated distribution substation 4. ... Indoor distribution substation 6. Outdoor distribution substation 7. Mobile distribution substation 

What are the uses of Thermistors ?

Description : What are the uses of Thermistors ?

Last Answer : Thermistors are frequently used in electronic circuits in which it is desired to provide temperature measurement, temperature control, and temperature compensation.

Explain with neat sketch the working principle of MIG.

Description : Explain with neat sketch the working principle of MIG.

Last Answer : In metal-arc inert gas welding the Weld area is shielded by an effectively inert atmosphere of argon, helium, carbon dioxide, or various other gas mixtures . The consumable bare Wire is fed automatically ... of the molten-weld puddle. Multiple-weld layers can be deposited at the joint. 

State the applications of TIG welding.

Description : State the applications of TIG welding.

Last Answer : The applications of TIG welding are as follows: 1. Mostly used to weld aluminum and aluminum alloys. 2. It is used to weld stainless steel, carbon base alloy, copper base alloy, nickel base alloy etc. 3. It is used to welding dissimilar metals. 4. It is mostly used in aerospace industries.

State the applications of rolling.

Description : State the applications of rolling.

Last Answer : Applications of rolling are as follows: 1. Concrete reinforcing bars. 2. Plates. 3. Wire rods. 4. Sheet and strip. 5. Rails. 6. Piping and tubes. 7. Body panels. 8. Construction materials

Define armature reaction in an alternator. Explain the effect of armature reaction at various P.F. of loads of alternator.

Description : Define armature reaction in an alternator. Explain the effect of armature reaction at various P.F. of loads of alternator.

Last Answer : Armature Reaction: The effect of armature flux on main flux is called as armature reaction.  Armature Reaction at Various Power Factors: When armature is loaded, the armature flux modifies ... lagging p.f. For capacitive loads the effect of flux is partly distorting and partly strengthening.

State the modification to be done in dc series motor to work satisfactorily as ac series motor. State applications of ac series motor.

Description : State the modification to be done in dc series motor to work satisfactorily as ac series motor. State applications of ac series motor.

Last Answer : Modifications are necessary in a dc series motor so that it operates satisfactorily on ac supply. The modifications are as follows:  1) AC series motor is built with a few field turns as ... and grinders 5) High speed vacuum cleaners 6) Sewing machines 7) Food processors 8) Drilling machine 

Explain the activities carried out during weekly maintenance of 3 ph. Induction motor.

Description : Explain the activities carried out during weekly maintenance of 3 ph. Induction motor. 

Last Answer : Activities Carried out During Weekly Maintenance of 3 ph. Induction Motor:  1) Check belt tension. In cases where this is excessive it should immediately be reduces and in the case of sleeve ... and cooled by oil mist systems its important to check the oil mist flow paths/pressure components.

Give the full form of SCADA & HMI.

Description : Give the full form of SCADA & HMI.

Last Answer : Full Form of SCADA and HMI:  SCADA:-Supervisory Control and Data Acquisition  HMI :- Human Machine Interface

Draw the block diagram of PLC.

Description : Draw the block diagram of PLC.

Last Answer : Block diagram of PLC and input/output devices used for PLC Input/output devices - The input module has bank of terminals for physically connecting input devices, like push buttons, limit switches etc. ... is to translate signals from the PLC's CPU into a form that the output device can use.

State the need of automation.

Description : State the need of automation. 

Last Answer : Need of Automation in Process : * To fulfill the demand of product at right time. * To reduce the human errors and involvement of human being in the process. * For better productivity. * For better ... of process. * For better quality. * For reducing man power. * For reducing cost of product.

Give the expression for ABCD constant of T model.

Description : Give the expression for ABCD constant of T model.

Last Answer : Expression for ABCD constants of T model: 

State the impact of inductance and resistance on transmission line performance

Description : State the impact of inductance and resistance on transmission line performance

Last Answer : Impact of inductance on transmission line: 1) It causes IXL drop in transmission line which affects regulation. 2) It is the only parameter which decides power transmission capacity of line i. ... is very small, it causes losses, temperature rise& poor voltage regulation so it cannot be neglected

State the needs and benefits of star labelling.

Description : State the needs and benefits of star labelling. 

Last Answer : Needs of star labelling: * Star labelling is meanly required to recognize quality of product * Star labelling is also required to determine life and efficiency of the product. * Star labels ... emission and air pollution will be reduces. 5. Market efficiency and compilation will be improve.