Ceramic recuperators (made of SiC) is economical, only when used for preheating combustion air above __________ °C. (A) 250 (B) 650 (C) 850 (D) 1000

Ceramic recuperators (made of SiC) is economical, only when used for
preheating combustion air above __________ °C.
(A) 250
(B) 650
(C) 850
(D) 1000
by

1 Answer

Answer :

(B) 650
by

Related questions

The temperature at which plastic layer formation takes place during carbonisation of coal varies from __________ °C. (A) 100 to 150 (B) 350 to 450 (C) 550 to 650 (D) 700 to 850

Description : The temperature at which plastic layer formation takes place during carbonisation of coal varies from __________ °C. (A) 100 to 150 (B) 350 to 450 (C) 550 to 650 (D) 700 to 850

Last Answer : (B) 350 to 450

Which of the following is the most suitable for preheating combustion air above 650°C? (A) Regenerator (B) Metallic recuperator (C) Ceramic recuperator (D) None of these

Description : Which of the following is the most suitable for preheating combustion air above 650°C? (A) Regenerator (B) Metallic recuperator (C) Ceramic recuperator (D) None of these

Last Answer : (C) Ceramic recuperator

Temperature attained in soldering of metals is about __________ °C. (A) 150-300 (B) 400-500 (C) 650-800 (D) 1000-1100

Description : Temperature attained in soldering of metals is about __________ °C. (A) 150-300 (B) 400-500 (C) 650-800 (D) 1000-1100

Last Answer : (A) 150-300

A small dairy farm daily produces 100 kilograms of average quality buffalo milk and sells it to an organised dairy at the rate of Rs. 100 per kilogram of total solids contained in the milk. How much would be the daily gross income of the farm from the sale of milk ? (A) Between Rs. 2,000 and Rs. 2,200 (B) Between Rs. 1,250 and Rs. 1,400 (C) Between Rs. 700 and Rs. 825 (D) Between Rs. 1,000 and Rs. 1,100 (E) Between Rs. 1,650 and Rs. 1,850

Description : A small dairy farm daily produces 100 kilograms of average quality buffalo milk and sells it to an organised dairy at the rate of Rs. 100 per kilogram of total solids contained in the milk. How much would be the daily gross ... (D) Between Rs. 1,000 and Rs. 1,100 (E) Between Rs. 1,650 and Rs. 1,850

Last Answer : (B) Between Rs. 1,250 and Rs. 1,400

Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Description : Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Last Answer : (B) 750

Ceramic recuperators compared to metallic recuperators for the same duty (A) Are lighter (B) Occupy more space (C) Are less costly (D) Have higher pressure differential between flue gas & air side

Description : Ceramic recuperators compared to metallic recuperators for the same duty (A) Are lighter (B) Occupy more space (C) Are less costly (D) Have higher pressure differential between flue gas & air side

Last Answer : (B) Occupy more space

Conversion of yellow phosphorous to red phosphorous is done by heating it in covered retorts at __________ °C in absence of air. (A) 50-80 (B) 250-400 (C) 1000-1200 (D) 800-900

Description : Conversion of yellow phosphorous to red phosphorous is done by heating it in covered retorts at __________ °C in absence of air. (A) 50-80 (B) 250-400 (C) 1000-1200 (D) 800-900

Last Answer : (B) 250-400

Ceramic recuperators are generally made of (A) Silicon carbide (B) Calcium carbide (C) Fireclay bricks (D) High alumina bricks

Description : Ceramic recuperators are generally made of (A) Silicon carbide (B) Calcium carbide (C) Fireclay bricks (D) High alumina bricks

Last Answer : (A) Silicon carbide

Maintain 850 OC for 1 hour (soaking time).  Cool the material to 60 OC in 4 hours. a) Calculate the efficiency of the furnace, if the specific heat of steel is 0.12 kcal/kgOC and fuel oil consumption per batch is 1400 litres.  GCV of fuel oil - 10200 kcal/kg,  Cost of fuel oil - Rs. 46,000/kL,  Sp. gr. of fuel oil - 0.92. b) Due to high cost of oil, the plant management decides to convert to a lower operating cost LPG fired furnace lined on the inside with ceramic fibre insulation and with an operating efficiency of 80%, for same requirement. The investment towards installation of the new furnace is Rs. 50 lakhs. Calculate the Return on Investment, if the plant operates two batches per day and 250 days in a year.  Cost of LPG - Rs. 75/kg,  GCV of LPG - 12500 kcal/kg.

Description : In a heat treatment shop, steel components are heat-treated in batches of 80 Tons. The  heat treatment cycle is as follows;  Increase temperature from 30 OC to 850 OC in 3 hours.  ... efficiency of 80%, for same requirement. The investment towards installation of  the new furnace is Rs. 50

Last Answer : Quantity of steel treated per batch - 80 Tons a. Efficiency of Furnace: Useful heat supplied to steel - 80000 x 0.12 x (850 - 30)   = 7872000 kcal/batch .1 mark Total heat ... = Rs. 64400/batch Efficiency of new LPG furnace - 80% Heat supplied in new LPG furnace - 7872000/0.8

Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Last Answer : (B) 130

Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Description : Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Last Answer : (A) Stoichiometric combustion air

Preheating temperature of medium viscosity furnace oil for better atomisation through burner is about __________ °C. (A) 50 (B) 70 (C) 90 (D) 140

Description : Preheating temperature of medium viscosity furnace oil for better atomisation through burner is about __________ °C. (A) 50 (B) 70 (C) 90 (D) 140

Last Answer : (C) 90

Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Description : Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect

Last Answer : (C) Either the fuel or the air or both, increases

The temperature in the calcium carbide furnace is __________ °C. (A) 200-300 (B) 700-850 (C) 2000-2200 (D) 4000-4500

Description : The temperature in the calcium carbide furnace is __________ °C. (A) 200-300 (B) 700-850 (C) 2000-2200 (D) 4000-4500

Last Answer : (C) 2000-2200

Optimum preheating temperature for pitch creosote mixture (PCM) which is also termed as C.T.F-200, before atomisation through burners is (A) 200 °F (B) 200 °C (C) 200 °K (D) 200 °R

Description : Optimum preheating temperature for pitch creosote mixture (PCM) which is also termed as C.T.F-200, before atomisation through burners is (A) 200 °F (B) 200 °C (C) 200 °K (D) 200 °R

Last Answer : (A) 200 °F

To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Description : To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Description : Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Description : Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Last Answer : (A) Increasing the draft in the furnace

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Description : In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Last Answer : (C) Combustion of coal by supplying it around the burner

Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Description : Preheating of combustion air is done to (A) Increase the adiabatic flame temperature (B) Increase the calorific value of the fuel (C) Complete the combustion of fuel (D) Reduce its requirement for effecting the complete combustion

Last Answer : (A) Increase the adiabatic flame temperature

Higher fuel combustion efficiency cannot be achieved by (A) Preheating of fuel gases & combustion air (B) Reducing sulphur content in the fuel (C) Adopting proper fuel firing technique & fuel preparation (D) Supplying correct amount of combustion air

Description : Higher fuel combustion efficiency cannot be achieved by (A) Preheating of fuel gases & combustion air (B) Reducing sulphur content in the fuel (C) Adopting proper fuel firing technique & fuel preparation (D) Supplying correct amount of combustion air

Last Answer : (B) Reducing sulphur content in the fuel

In general, the limit of inflammability/explosion limit of fuel gases is widened by the (A) Increase in gas pressure (B) Increase in temperature (i.e. preheating) (C) Use of pure oxygen for combustion instead of air (D) All (A), (B) & (C)

Description : In general, the limit of inflammability/explosion limit of fuel gases is widened by the (A) Increase in gas pressure (B) Increase in temperature (i.e. preheating) (C) Use of pure oxygen for combustion instead of air (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Description : In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air

Last Answer : (C) Combustion of coal by supplying it around the burner

Transmission of oil should be changed after every working hours about a) 550 hours b) 650 hours c) 70 hours d) 850 hours

Description : Transmission of oil should be changed after every working hours about a) 550 hours b) 650 hours c) 70 hours d) 850 hours

Last Answer : c) 70 hours

A 6 month project in R&D costs____________; while a 12 month project in R&D costs ________. a. 1,000,000; 1,500,000 b. 650,000; 850,000 c. 500,000; 1,000,000 d. 750,000; 1,000,000 e. 1,000,000; 750,000

Description : A 6 month project in R&D costs____________; while a 12 month project in R&D costs ________. a. 1,000,000; 1,500,000 b. 650,000; 850,000 c. 500,000; 1,000,000 d. 750,000; 1,000,000 e. 1,000,000; 750,000

Last Answer : c. 500,000; 1,000,000

Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Description : Economizer is provided to utilize the flue gas heat for ___ a) preheating the boiler feed water b) preheating the stock c) preheating the combustion air d) preheating fuel

Last Answer : preheating the boiler feed water

Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are normally carried out at about __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Description : Gasification of the solid fuel converts its organic part into combustible by interaction with air/oxygen and steam so as to obtain a secondary gaseous fuel of high calorific value having no ash. Gasification reactions are ... __________ °C. (A) 400-500 (B) 900-1000 (C) 1400-1500 (D) 1700-1800

Last Answer : (B) 900-1000

In case of liquid petrofuels, momentary combustion is observed at its (A) Flash point (B) Preheating temperature corresponding to viscosity of 25 centistokes (C) Flame temperature (D) Fire point

Description : In case of liquid petrofuels, momentary combustion is observed at its (A) Flash point (B) Preheating temperature corresponding to viscosity of 25 centistokes (C) Flame temperature (D) Fire point

Last Answer : (A) Flash point

A 20 L container holds 0.650 mol of He gas at 37 °C at a pressure of 628.3 bar.

Description : A 20 L container holds 0.650 mol of He gas at 37 °C at a pressure of 628.3 bar.

Last Answer : A 20 L container holds 0.650 mol of He gas at 37°C at a pressure of 628.3 bar. What will be new ... and 1.25 mol of additional He gas was added to it?

Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280

Description : Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280

Last Answer : (D) 250-280

90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at a temperature of __________ °C. (A) -5 (B) 10-30 (C) 250-280 (D) 500-600

Description : 90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at a temperature of __________ °C. (A) -5 (B) 10-30 (C) 250-280 (D) 500-600

Last Answer : (C) 250-280

Light oil whose major component is Benzol, is obtained by the distillation of crude tar in the temperature range of __________ °C. (A) 80-170 (B) 200-300 (C) 250-270

Description : Light oil whose major component is Benzol, is obtained by the distillation of crude tar in the temperature range of __________ °C. (A) 80-170 (B) 200-300 (C) 250-270

Last Answer : (A) 80-170

Fusion zone in the electric furnace used for reduction of phosphate rock to elemental phosphorous is maintained at __________ °C. (A) 250-300 (B) 500-750 (C) 950-1050 (D) 1400-1450

Description : Fusion zone in the electric furnace used for reduction of phosphate rock to elemental phosphorous is maintained at __________ °C. (A) 250-300 (B) 500-750 (C) 950-1050 (D) 1400-1450

Last Answer : (D) 1400-1450

Fermentation of molasses to produce ethyl alcohol is done at __________ °C. (A) 20 - 30 (B) < - 5 (C) 100 - 150 (D) 250 - 300

Description : Fermentation of molasses to produce ethyl alcohol is done at __________ °C. (A) 20 - 30 (B) < - 5 (C) 100 - 150 (D) 250 - 300

Last Answer : (A) 20 - 30

90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at __________ °C. (A) < 0 (B) 10-30(C) 250-280 (D) 500-600

Description : 90% of the caprolactam is converted to nylon-6 on its condensation polymerisation in the reactor maintained at __________ °C. (A) < 0 (B) 10-30 (C) 250-280 (D) 500-600

Last Answer : (B) 10-30

Mercury electrolytic cell produces 50-70% NaOH solution. Its operating temperature is __________ °C. (A) 25 (B) 60-70 (C) 150-200 (D) 250-300

Description : Mercury electrolytic cell produces 50-70% NaOH solution. Its operating temperature is __________ °C. (A) 25 (B) 60-70 (C) 150-200 (D) 250-300

Last Answer : (B) 60-70

Exothermic condensation reaction of monochlorobenzene with chloral in presence of 20% oleum as catalyst produces DDT. The reaction temperature is maintained at __________ °C. (A) 15-30 (B) 90-100 (C) 250-300 (D) < 0

Description : Exothermic condensation reaction of monochlorobenzene with chloral in presence of 20% oleum as catalyst produces DDT. The reaction temperature is maintained at __________ °C. (A) 15-30 (B) 90-100 (C) 250-300 (D) < 0

Last Answer : (A) 15-30

Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300

Description : Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300

Last Answer : (C) 350-400

Molecular sieves are regenerated by heating to __________ °C. (A) < 150 (B) 200-330 (C) > 500 (D) > 1000

Description : Molecular sieves are regenerated by heating to __________ °C. (A) < 150 (B) 200-330 (C) > 500 (D) > 1000

Last Answer : (B) 200-330

Fusion point of coal ash generally varies from 1000 to 1700° C. Ash having fusion point less than __________ °C is liable to form clinker. (A) 1100 (B) 1250 (C) 1350 (D) 1400

Description : Fusion point of coal ash generally varies from 1000 to 1700° C. Ash having fusion point less than __________ °C is liable to form clinker. (A) 1100 (B) 1250 (C) 1350 (D) 1400

Last Answer : (A) 1100

Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Description : Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Last Answer : (A) 700 - 1000

Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C. (A) 80-120 (B) 200-300 (C) 600-800 (D) 1000-1100

Description : Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C. (A) 80-120 (B) 200-300 (C) 600-800 (D) 1000-1100

Last Answer : (D) 1000-1100

The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99

Description : The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99

Last Answer : (C) 85

Typical waste gases temperature from glass melting furnace a) 1000-1550 oC b) 800-950 oC c) 650–750 oC d) 760-815 oC

Description : Typical waste gases temperature from glass melting furnace a) 1000-1550 oC b) 800-950 oC c) 650–750 oC d) 760-815 oC

Last Answer : 1000-1550 oC

The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300

Description : The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300

Last Answer : (B) 1 and 200

Helical screw agitator is used for (A) Mixing highly viscous pastes (B) Blending immiscible liquids (C) Mixing liquids at very high temperature (> 250 °C) (D) None of these

Description : Helical screw agitator is used for (A) Mixing highly viscous pastes (B) Blending immiscible liquids (C) Mixing liquids at very high temperature (> 250 °C) (D) None of these

Last Answer : (A) Mixing highly viscous pastes

The average threshing outrun of a paddy in kg/hr is (A) 500 (B)650 (C)800 (D)1000

Description : The average threshing outrun of a paddy in kg/hr is (A) 500 (B)650 (C)800 (D)1000

Last Answer : (B)650

Seven men, five women and eight children were given as assignment of distributing 2000 books to students in a school over a period of three days. All of them distributed books on the first day. One of the second day two women and three children remained absent and on the third day three men and five children remained absent. If the ratio of the number of books distributed in a day by a man, a woman and a child was 5 : 4 : 2 respectively, a total of approximately how many books were distributed on the second day? a) 1000 b) 800 c) 650 d) 900 e) Cannot be determined

Description : Seven men, five women and eight children were given as assignment of distributing 2000 books to students in a school over a period of three days. All of them distributed books on the first day. One of the second ... distributed on the second day? a) 1000 b) 800 c) 650 d) 900 e) Cannot be determined

Last Answer : Answer: C Sol. Let the books distributed by man, a woman and a child be 5x, 4x and 2x respectively. ∴ No. of books distributed in 1st day = 7 5x+5 4x+8 2x=71x No. of books distributed in 2nd day =7 ... 2x=46x 71x + 57x + 46x = 2000, x = 2000/174 57x=2000/174 57= 655 650 (Approx)

About IELTS General Examination,Examination Date,Examination Score,Examination Eligibility,Examination Fee,How to ApplyBenefits of Taking the Examination,Career Scope after Appearing for the Examination.WRITE ABOUT IT in AROUND 850 TO 1000 WORD?

Description : About IELTS General Examination,Examination Date,Examination Score,Examination Eligibility,Examination Fee,How to ApplyBenefits of Taking the Examination,Career Scope after Appearing for the Examination.WRITE ABOUT IT in AROUND 850 TO 1000 WORD?

Last Answer : 1400000