Operation of blast furnace stove is based on the principles of a
__________ furnace.
(A) Regenerative
(B) Recuperative
(C) Both (A) and (B)
(D) Neither (A) nor (B)

1 Answer

Answer :

(A) Regenerative

Related questions

Description : Pot furnace which is either regenerative or recuperative, is used in the manufacture of (A) Glass (B) Stainless steel (C) Potteries (D) Refractory bricks

Last Answer : (A) Glass

Description : Which is a regenerative furnace? (A) Coke oven heating chamber (B) Open hearth furnace (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Description : Types of waste heat exchanger are: a) Regenerative and recuperative burners b) Economizers c) Waste heat boilers d) All of the above

Last Answer : All of the above

Description : In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Description : Which one is not an induced draught furnace? (A) Blast furnace stove (B) Sintering furnace (C) High pressure boiler (D) None of these

Last Answer : (A) Blast furnace stove

Description : Fuel used in B.F. stove is (A) Pulverised coal (B) Furnace oil (C) Blast furnace gas/mixed gas (D) Coke oven gas

Last Answer : (C) Blast furnace gas/mixed gas

Description : An example of recuperative furnace is the (A) Soaking pit (B) Open hearth furnace (C) Coke ovens (D) None of these

Last Answer : (A) Soaking pit

Description : Which of the following is not a recuperative furnace? (A) Soaking pit (B) Reheating furnace (C) Steam boiler (D) Coke oven

Last Answer : (D) Coke oven

Description : The important dimensional group involved in the power requirement calculation in mixing operation is the __________ number. (A) Reynold's (B) Froude (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Description : In case of constant underflow extraction operation, the __________ atall solute concentration. (A) Solids are drained to the same extent (B) Ratio of the insoluble to solution is constant (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Description : Regenerators are installed in (A) Coke ovens (B) Open hearth furnace (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Description : The main function of a muffle in the muffle furnace is to (A) Protect the charge from the effects of the products of combustion (B) Smooth out temperature inequalities on the combustion side of the muffle wall (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Description : The heating capacity of muffle furnace depends on the (A) Surface area & emissivity of the stock (B) Properties of the muffle wall (temperature, area, and emissivity) (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Description : Example of an indirectly heated furnace is (A) Hood annealing furnace (B) Muffle furnace (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Description : In a grinding operation, the limiting particle size is the size of the __________ particle in the sample. (A) Smallest (B) Largest (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

Description : Abstraction and encapsulation are fundamental principles that underlie the object oriented approach to software development. What can you say about the following two statements? I. Abstraction allows us to focus on what something ... and II are correct. (3) Only II is correct. (4) Only I is correct.

Last Answer : (1) Neither I nor II is correct.

Description : The progressive operation of the contactors marked 'A' provide the winch shown in the illustration with __________. EL-0102 A. accumulation B. dynamic braking C. acceleration D. regenerative braking

Last Answer : Answer: C

Description : The impure iron (pig iron) that is tapped out from blast furnace contains about __________ percent carbon. (A) 0.2 (B) 2 (C) 4 (D) 8

Last Answer : (C) 4

Description : __________ atmosphere is maintained inside an iron blast furnace. (A) Oxidising (B) Reducing (C) Inert (D) Decarburising

Last Answer : (B) Reducing

Description : Thermal efficiency of blast furnace stoves used for heating blast (air) may be about __________ percent. (A) 20 (B) 40 (C) 60 (D) 80

Last Answer : (D) 80

Description : Size of blast furnace grade coke is __________ mm. (A) 25-80 (B) 0-15 (C) 15-25 (D) > 100

Last Answer : (A) 25-80

Description : Explosion limit of blast furnace gas is 37 to 71% gas in gas-air mixture. It means that the blast furnace gas will explode when burnt in a confined space, if its concentration in the gas-air mixture is __________ percent. (A) < 37% (B) > 71% (C) In between 37 & 71% (D) None of these

Last Answer : (C) In between 37 & 71%

Description : Dust content in raw blast furnace gas is about __________ gm/Nm3 ; hence it is cleaned to the dust level of about < 10 mg /Nm3 before use. (A) 15-30 (B) 1-2 (C) 70-100 (D) 150-200

Last Answer : (A) 15-30

Description : Yield of blast furnace gas is about __________ Nm3 /ton of pig iron. (A) 300 (B) 2000 (C) 5000 (D) 10000

Last Answer : (B) 2000

Description : Abrasion index of blast furnace coke should be around __________ percent. (A) 20 (B) 35 (C) 55 (D) 80

Last Answer : (D) 80

Description : Main use of soft coke is as __________ fuel. (A) Domestic (B) Blast furnace (C) Foundry (D) None of these

Last Answer : (A) Domestic

Description : Blast furnace gas is a very poisonous gas because of its predominantly high __________ content. (A) H2O (B) CO2 (C) CO (D) CH4

Last Answer : (C) CO

Description : Calorific value of blast furnace gas is around __________ KCal/Nm3 . (A) 850 (B) 1800 (C) 4200 (D) 6500

Last Answer : (A) 850

Description : Waste/polluted water discharged from electroplating, blast furnace and coal mining industries contain mainly __________ substances. (A) Radioactive (B) Organic (C) Inorganic (D) None of these

Last Answer : (C) Inorganic

Description : __________ is used as a flux in the extraction of iron from iron ore (haematite) in blast furnace. (A) Bauxite (B) Limestone (C) Quartz (D) Manganese

Last Answer : (B) Limestone

Description : Specific gravity of hot metal (pig iron) is __________ times that of the blast furnace slag. (A) 2 (B) 3 (C) 0.8 (D) 6

Last Answer : (B) 3

Description : Limestone addition in the blast furnace is done to flux __________ present in the raw materials. (A) SiO2 (B) Al2O3 (C) MnO2 (D) P

Last Answer : Limestone addition in the blast furnace is done to flux __________ present in the raw materials. (A) SiO2 (B) Al2O3 (C) MnO2 (D) P

Description : The approximate height of a blast furnace having a useful volume of 2000 m3is about __________ metres (A) 25 (B) 35 (C) 55 (D) 75

Last Answer : (C) 55

Description : Volume of blast furnace slag is about __________ times the volume of hot metal (pig iron) of the same weight (A) 1.5 (B) 3 (C) 5

Last Answer : Option B

Description : Coke ovens in steel plant are heated by (A) Electricity (B) Blast furnace gas/mixed gas (C) Coke oven gas (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Description : In levelling operation (A) When the instrument is being shifted, the staff must not be moved (B) When the staff is being carried forward, the instrument must remain stationary (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b)

Description : Petroleum coke is used mainly in the (A) Discoloration of yellow glycerine (B) Sugar refining (C) Manufacture of carbon electrode (D) Blast furnace for reduction of iron ore

Last Answer : (C) Manufacture of carbon electrode

Description : The most efficient equipment for the removal of sub-micronic dust particles from blast furnace gas is the (A) Venturi atomiser (B) Gravity settling chamber (C) Electro-static precipitator (D) Cyclone separator

Last Answer : (C) Electro-static precipitator

Description : Raw materials are charged in the iron blast furnace using (A) Bucket elevator (B) Skip hoist (C) Screw conveyor (D) None of these

Last Answer : (B) Skip hoist

Description : Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of (A) Furnace oil with air (B) Furnace oil with oxygen (C) Blast furnace gas with air (D) Blast furnace gas with oxygen

Last Answer : (C) Blast furnace gas with air

Description : Heat transfer takes place through a liquid medium surrounding the submerged material under heating, in case of a/an (A) Blast furnace (B) Steam boiler (C) Salt bath furnace (D) Annealing furnace

Last Answer : (C) Salt bath furnace

Description : Reducing atmosphere is maintained in a (A) Calcination kiln (B) Blast furnace (C) Soaking pit (D) L.D. converter

Last Answer : (B) Blast furnace

Description : Blast furnace stoves are meant for heating (A) Air (B) Blast furnace gas (C) Steam (D) None of these

Last Answer : (A) Air

Description : Regenerators are used for waste heat recovery in (A) By-product coke ovens (B) Beehive coke oven (C) Blast furnace stoves (D) Soaking pits

Last Answer : (A) By-product coke ovens

Description : Which furnace employs an I.D. fan for the removal of flue gases from the furnace? (A) Coke oven (B) Blast furnace stoves (C) Beehive coke oven (D) High pressure boiler

Last Answer : (D) High pressure boiler

Description : An example of shaft furnace is the (A) L.D. converter (B) Glass melting tank (C) Blast furnace (D) Soaking pit

Last Answer : (C) Blast furnace

Description : . An example of a periodic furnace is the (A) Blast furnace stoves (B) Blast furnace (C) Coke oven heating chamber (D) Rotary kilns

Last Answer : (A) Blast furnace stoves

Description : Which of the following is not a by-product fuel? (A) Producer gas (B) Blast furnace gas (C) Coke oven gas (D) Refinery gas

Last Answer : (A) Producer gas

Description : Which of the following has the least calorific value (kcal/Nm3 )? (A) Blast furnace gas (B) Coke oven gas (C) Sewage gas (D) Natural gas

Last Answer : (A) Blast furnace gas

Description : Which of the following gaseous fuels has the lowest calorific value? (A) Gobar gas (B) Refinery gas (C) Converter gas (D) Blast furnace gas

Last Answer : (D) Blast furnace gas