Draw construction of SCR using two transistor model. Explain its operation.

1 Answer

Answer :

Two Transistor Model of SCR or Thyristor

image

Related questions

Description : Draw the circuit diagram of battery charger using SCR and explain it’s working.

Last Answer : Battery charger circuit using SCR: The figure shows the battery charger circuit using SCR. A 12V discharged battery is connected in the circuit and switch SW is closed. The singlephase 230V ... not fired. In this way, after full charging, further charging is automatically stopped.

Description : Draw a neat labelling V-I characteristics of SCR and explain the region

Last Answer : (i) Latching current: It is the minimum anode current required to maintain the SCR in the conduction state just after turn-on and the gate signal has been removed.  (ii) Holding current: It is the minimum anode current required to hold the conducting SCR in the ON state. 

Description : Explain triggering of SCR using opto-coupler. State its advantages. 

Last Answer : Triggering of SCR using opto-coupler:  A simple opto-coupler based triggering circuit for SCR is shown in the figure. An optocoupler or opto-isolator is a combination of light source ... is small size and light weight device. iii)Interfacing with logic circuits is easily possible.

Description : Draw the V-I characteristics of power transistor. 

Last Answer : V-I characteristics of power transistor:

Description : Explain working of AC circuit breaker using SCR with circuit diagram.

Last Answer : AC Circuit Breaker:  The circuit configuration of static AC circuit breaker using SCR is shown in the figure. When switch S' is closed, the SCRs T1 and T2 are fired in positive ... to non-availability of gate current. Thus the maximum time delay for breaking the circuit is one half-cycle.

Description : Temperature controller using SCR

Last Answer : Temperature controller using SCR The temperature control circuit is used to regulate the temperature. Figure shows the temperature control circuit using thermostat as temperature detector and SCR as ... half-cycle and heater gets connected to source to produce heat and raise the temperature.

Description : Describe triggering of SCR using UJT relaxation oscillator. 

Last Answer : I need it's operation

Description : Explain the thermal triggering method of SCR. Enlist different triggering methods of SCR.

Last Answer : Types of Triggering: 1) Forward voltage triggering 2) Thermal triggering (Temperature triggering) 3) Radiation triggering (Light triggering) 4) dv/dt triggering 5) Gate triggering ... generated leakage current increases. This current gets multiplied internally and thyristor is turned on. 

Description : Compare SCR and TRIAC

Last Answer : SCR TRIAC It is an unidirectional device. It is a bidirectional device. It is turned-on by only positive gate current. It can be turned-on by either ... applications including lamp dimmer, heating control, zero voltage switched AC relay, small AC motor control etc.

Description : How GTO is advantages over SCR

Last Answer : i) It is turned-off by negative gate pulse. ii) No commutation circuit required, reducing the cost, size, weight and volume of the circuit. iii) As commutation choke is not used, the associated acoustic ... turn off time permits high switching frequency. v) It has higher di/dt rating at turn-off. 

Description : SCR is more utilized as compared to Triac because it is

Last Answer : SCR is more utilized as compared to Triac because it is available with higher ratings

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

Description : An SCR without any external connections is considered as (A) two diodes in series (B) three diodes in series (C) two n-p-n transistors in series (D) two p-n-p transistors in series

Last Answer : An SCR without any external connections is considered as three diodes in series

Description : Is a SCR a thyristor?

Last Answer : Yes, SCR is a thyristor. Thyristor is the family and SCR is the member of that family but SCR is universally known as thyristor.

Last Answer : Yes, SCR is a unidirectional switch.

Last Answer : SCR turned off when the anode current falls below holding current.

Description : What is holding current and latching current in SCR? Draw the gate characteristics of an SCR and explain the characteristics. What are the different signals which can be used for turning on SCR by gate control? compare them.

Last Answer : (i) Holding Current: Holding current is defined as the minimum anode current required to maintain conducting SCR in the on-state.  (ii) Latching Current: Latching current is defined as the ... the on-state immediately after the SCR has been turned on and the gate signal has been removed.

Description : What is the use of SCR?

Last Answer : SCR are use in lamp dimming, power regulators, motor control, rectifications of high power AC, control of welding machines and also use as switch these are some uses of silicon controlled rectifier.

Description : Draw and explain self-basing of a transistor.

Last Answer : Transistor Biasing is the process of setting a transistors DC operating voltage or current conditions to the correct level so that any AC input signal can be amplified correctly by the transistor. ExplanationIt ... Applying KVL to o/p loop , Collector-emitter voltage, VCE = VCC − IC RC

Description : Draw construction of IGBT.

Last Answer : construction of IGBT

Description : Purpose of Selective Catalytic Reduction (SCR)

Last Answer : Purpose of Selective Catalytic Reduction (SCR) : 1. It reduces Nox 75% to 90% 2. Converts it in to molecular nitrogen and water vapor 3. It reduces HC emission up to 80% 4. It reduces PM emission 20 to 25%.

Description : An inductor is connected in series with SCR to protect it from A) Excessive high voltage B) Excessive high dv/dt C) Excessive high di/dt D) Excessive large forward current 

Last Answer : An inductor is connected in series with SCR to protect it from Excessive high di/dt

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

Description : In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in (A) voltage notching (B) harmonic distortion (C) voltage sag (D) voltage swell

Last Answer : In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in voltage notching

Description : Describe thermal runaway of transistor and explain how it can be avoided.

Last Answer : Concept of thermal runaway:  1.We know that  IC = β IB + (1+ β) ICO  Where ICO is the leakage current and ICO is strongly dependent on temperature. 2. Leakage current approximately doubles for ...   Thermal runaway can be avoided by : 1) Using stabilization circuitry 2) Heat sink 

Description : Explain working of n-p-n transistor in unbiased condition.

Last Answer : Construction of NPN transistor: For an unbiased transistor no external power supplies are connected to it. Base is sandwiched between collector & emitter terminal. It is thin & lightly doped ... providing external power supply to transistor & this process is known as Biasing.

Description : With neat diagram explain working of NPN transistor.

Last Answer : N-p-n transistor is made by sandwiching thin layer of p-type semiconductor between two layers of n-type semiconductor. It has three terminals - Emitter, Base and collector. The npn transistor has two ... up in the collector as it is more positive. In this way, current flows in the transistor.

Description : Compare P.N.P and N.P.N transistor.

Last Answer : Parameter PNP transistor NPN transistor Definition Two blocks of p- types semiconductors are separated by one thin block of n-type semiconductor. Transistor in which two ntype layer ... Positive Voltage  Emitter Terminal Collector Terminal Ground Signal High Low

Description : Define α and β of the transistor. 

Last Answer : α: The ratio of collector current IC to emitter current IE for a constant collector to base voltage VCB in the CB configuration is called current gain alpha (α).   β : The ratio of collector ... a constant collector to emitter voltage VCE in the CE configuration is called current gain beta (β) .

Description : List various transistor biasing methods.

Last Answer : Types of biasing methods: i. Base bias (or fixed bias) ii. Base bias with emitter feedback. iii. Base bias with collector feedback iv. Voltage divider bias (or self bias) v. Emitter bias. 

Description : Transistor operating configurations

Last Answer : Transistor operating configurations

Description : Define junction field effect transistor (JFET) and give an example.

Last Answer : Junction Field-Effect Transistor: It is a semiconductor device having three terminals, namely Gate, Drain and Source, in which the current flow is controlled by an electric field set up by an external voltage applied ... : i) n-channel JFET and ii) p-channel JFET Examples of JFET: BFW 10, BFW 11 

Description : Define α & β and derive the relation between (α) &) (β) of transistor.

Last Answer : α : The ratio of output collector current IC to input emitter current IE in the CB configuration is called current gain alpha (α).  β : The ratio of output collector current IC to the input base current IB in the CE configuration is ... ( 1/β) + 1  hence 1/ α = (1+β )/ β  Therefore, α = β /(1+β)

Description : Define biasing of transistor

Last Answer : Biasing of transistor is the process that makes the base emitter junction of transistor always forward biased and collector junction reverse biased for achieving the faithful amplification .

Description : Compare between CB , CE & CC transistor configuration.

Last Answer : Parameter CB CE CC I/P impedance Low Or 50Ω Medium Or 600Ωto 4kΩ High Or 1 MΩ Current Gain Less than or equal to 1 High Highest Voltage Gain Medium Medium Less ... k Ω to 50 k Ω Low Or 50 Ω Phase shift between input and output 0° 360° 0° 

Description : Why transistor is called as bipolar device.

Last Answer : BJT is called bipolar device because in BJT current conduction takes place due to majority as well as minority charge carriers that is because of electrons as well as holes.

Description : What is the main use of a transistor?

Last Answer : Main use of a transistor as amplifier and as switch.

Description : Explain two-quadrant chopper.........

Last Answer : Two quadrant chopper:  There are two semiconductor controllable switches in the two-quadrant chopper. Two quadrant type A chopper: The figure shows the type A chopper. Both the switch never turn on at ... 2 are turned on then Vo=Vs. When chopper 1 and chopper 2 are off then Vo=-Vs.

Description : What does everyone think about the transgendered model on America's Next Top Model?

Last Answer : I think she’s awesome for doing this and I wish her all the luck in the world.

Description : How To Make A Model Rocket

Last Answer : Need a project for the upcoming science fair? The model rocket is your ticket to the prestigious best in show award. Imagine your own self-made toy that can launch itself past the ceiling of ... be hailed as your school's official rocketeer, and rake in awards and accolades at the science fair.

Description : How to Make a DNA Model

Last Answer : How to Make a DNA Model A DNA model is an interesting way to bring the DNA that dictates the fiber of our being. It can help us understand the physical make-up of DNA and can make for a ... balls. Let the glue dry overnight. You can also do this project using alternative materials, such as candies.

Description : How to Build a Model Sailboat ?

Last Answer : How to Build a Model Sailboat How to Build a Model Sailboat For those that love boats, it can be a magical experience spending the summer on the sea. Unfortunately, a private boat is way ... builders. They can also help you choose between many small model sailboat pieces used to create your ship.

Description : Give the expression for ABCD constant of T model.

Last Answer : Expression for ABCD constants of T model: 

Description : The power flow problem mathematical model for a linear transmission network (A) is non-linear (B) is linear (C) considers time variation of generation (D) does not consider tap-changing transformers

Last Answer : The power flow problem mathematical model for a linear transmission network is non-linear

Description : What is dataflow model?

Last Answer : Dataflow model: In dataflow model, all nodes may execute concurrently. The figure shows the dataflow models. Dataflow models consist of processes.

Description : Draw construction of Megger and write operating principle of it.

Last Answer : Megger:  Working: Two coils the current coil and pressure coil are mounted at an angle on the same spindle and form the part of the moving system. These coils are connected to a small hand driven ... . When the instrument is not working the pointer may rest at any position on the dial.

Description : How thick do you make the exterior and interior walls of a residence if you are using Post and Beam construction instead of standard Timber Frame?

Last Answer : Post and Beam is historically 10 to 12 inches by the same. . . so wall thickness of up to 12 inches. I owned a 1720’s center chimney with post and beam.

Description : Explain construction and working of AC servomotor.

Last Answer : Construction of AC Servo Motor: AC servo motor is mainly composed of a stator and a rotor. Laminated stator core is usually made of silicon steel. Two phase windings are placed in the stator slots at 90 degree ... on rotor. Due to the force or torque acting on the rotor, it is set in motion. 

Description : Explain the construction and working of LVDT accelerometer with the help of diagram.

Last Answer : Explanation:* The LVDT accelerometer consists of one primary and two secondary windings which are placed on either side of central code. The two ends of the core are connected with ... in the output terminal. This output voltage is directly proportional to the vibration or acceleration.