Define : (i) CMMR ii) Slew rate

Define : (i) CMMR ii) Slew rate
by
retagged

1 Answer

Answer :

(i) CMRR:- The CMRR is defined as the ratio of the powers of the differential gain over the common-mode gain, measured in positive decibels (thus using the 20 log rule): As differential gain should exceed common-mode gain, this will be a positive number, and the higher the better. 


CMRR= ADM/ACM



ii) Slew rate: The slew rate of an op amp or any amplifier circuit is the rate of change in the output voltage caused by a step change on the input. OR -The maximum rate at which an amplifier can respond to an abrupt change of input level It is measured as a voltage change in a given time.

by

Related questions

How to Slow Your Heart Rate ?

Description : How to Slow Your Heart Rate ?

Last Answer : How to Slow Your Heart Rate Tachycardia or palpitation is a condition where your heart rate is higher than the normal value of 60-100 beats per minute (bpm) . This is usually a symptom ... An early detection of any illness is very important to prevent it from getting worse and avoid complications.

How to Calculate Your Heart Rate ?

Description : How to Calculate Your Heart Rate ?

Last Answer : How to Calculate Your Heart Rate The heart rate reflects your current state of health, more specifically, it shows your fitness level and at some point, your metabolic rate. It is only a rough estimate ... often feel light, active, and happy each time, since they are clear signs of good health.

What are the different heart rate monitors and how to make a choice?

Description : What are the different heart rate monitors and how to make a choice?

Last Answer : What are the different heart rate monitors and how to make a choice? The time when only professional athletes could afford training with a heart rate monitor is already in the past. Today literally anyone ... is that the device can withstand dives to a depth of more than 10 meters. Happy choice!

Draw venture meter and write steps to measure flow rate.

Description : Draw venture meter and write steps to measure flow rate.

Last Answer : Venturi meter consists of three sections that is converging section, throat section and diverging section. The flow is introduced to the meter through the inlet with diameter D' . The inclined angle ... to 15o . Flow rate is proportional to the square root of the differential pressure.

If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be

Description :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be A) Large in amplitude B) Small in amplitude C) Distorted D) Distortion less

Last Answer :  If a signal band limited to fm is sampled at a rate less than 2fm, then the constructed signal will be Distorted 

The unit heat rate characteristic of a thermal power unit shows :

Description : The unit heat rate characteristic of a thermal power unit shows :  (A) Heat input per kWh of output versus the megawatt output of unit  (B) Heat input per kW of output versus the megawatt output ... hour output of unit  (D) Heat input per kW of output versus the megawatt hour output of unit

Last Answer : The unit heat rate characteristic of a thermal power unit shows : Heat input per kWh of output versus the megawatt output of unit 

Liquid flow rate is measured using

Description : Liquid flow rate is measured using (A) a pirani gauge (B) a pyrometer (C) an orifice plate (D) a bourdon tube

Last Answer : Liquid flow rate is measured using an orifice plate

The initial rate of rise of current through a coil of inductance 10 H when suddenly...

Description : The initial rate of rise of current through a coil of inductance 10 H when suddenly connected to a D.C. supply of 200 V is_______Vs.

Last Answer : The initial rate of rise of current through a coil of inductance 10 H when suddenly connected to a D.C. supply of 200 V is 20 Vs

The rate of rise of current through an inductive coil is maximum?

Description : The rate of rise of current through an inductive coil is maximum?

Last Answer : The rate of rise of current through an inductive coil is maximum at the start of the current flow.

The rate of acceleration on suburban or urban service is in the range?

Last Answer : The rate of acceleration on suburban or urban service is in the range 1.6 to 4.0 km phps.

In Hopknison demand rate or two part tariff the demand rate or fixed charges are?

Last Answer : In Hopknison demand rate or two part tariff the demand rate or fixed charges are dependent upon the maximum demand of the consumer.

Explain data transfer mechanism in I2C protocol.

Description : Explain data transfer mechanism in I2C protocol. Compare it with CAN and USB protocol based on bit rate and area of applications.

Last Answer : I2C (Inter-Integrated Circuit): I2C stands for Inter-Integrated Circuit. I2C is a serial protocol. It was developed by Philips Semiconductor. I2C bus have two communication lines. One is serial data ( ... Mbps this is used for lower speed devices. Using USB we can connect upto 127 devices.

Define each of following terms of operational amplifiers i) Slew rate ii) Input offset voltage iii) Voltage gain iv) Input capacitance

Description : Define each of following terms of operational amplifiers i) Slew rate ii) Input offset voltage iii) Voltage gain iv) Input capacitance

Last Answer : i) Slew rate:- Maximum rate of change of o/p voltage per unit of time. It is express in volt/µsec.  ii) Input offset voltage:- The voltage that must be applied between two ... capacitance that can be measured at either be inverting or non-inverting terminal with other terminal connected to ground.

Define: i) Accuracy ii) Precision iii) Measurement uncertainty iv) Tolerance.

Description : Define: i) Accuracy ii) Precision iii) Measurement uncertainty iv) Tolerance.

Last Answer : Accuracy is the ability of the instrument to measure the accurate value. In other words, it is the closeness of the measured value to a standard or true value.

Define : i) Strain gauge ii) Gauge factor

Description : Define : i) Strain gauge ii) Gauge factor

Last Answer : i) Strain gauge is a resistance transducer whose resistance varies with applied force; It converts force, pressure, tension, weight, etc., into a change in electrical resistance which can then be measured ... is defined as the ratio of per unit change in resistance to per unit change in length 

Define the static characteristics: i) Resolution ii) Drift.

Description : Define the static characteristics: i) Resolution ii) Drift.

Last Answer : i) Resolution: It is the smallest increment in the input which can be detected by the instrument or the smallest measurable input change.  ii) Drift: The gradual shift in the indication or record of ... of time, during which the true value of the variable does not change is referred to as drift. 

Define: i) Calibration ii) Traceability

Description : Define: i) Calibration ii) Traceability

Last Answer : i) Calibration: Comparison of an unknown quantity to a known standard quantity.  ii) Traceability: It is defined as an unbroken chain of comparisons relating an instrument's measurements to a known ... to a traceable standard can be used to determine an instrument's bias, precision, and accuracy.

Define: i) Sensitivity ii) Linearity

Description : Define: i) Sensitivity ii) Linearity

Last Answer : i) Sensitivity: It is the ratio of magnitude of output signal to the magnitude of input signal.  ii) Linearity is defined as the ability to reproduce the input characteristics symmetrically and this can be expressed by ... the output, x is the input, m is the slope and c is the intercept.

Define: i) Range ii) Span of instruments

Description : Define: i) Range ii) Span of instruments

Last Answer : i) Range: It is defined as the difference between Greatest and Smallest value of the data or reading of the instrument.  ii) Span: It is defined as the algebraic difference between the upper and lower range values

Define slew rate?

Description : Define slew rate?

Last Answer : Slew rate can be defined as the maximum rate of change of output voltage of op-amp with respect to time.

Define slew rate.

Description : Define slew rate.

Last Answer : The slew rate is defined as the maximum rate of change of output Voltage caused by a step input voltage.An ideal slew rate is infinite which means that op-amp’s output voltage should change instantaneously in response to input step voltage.

What is Slew Rate ? What is the sleeve rate ?

Description : What is Slew Rate ? What is the sleeve rate ?

Last Answer : : Sluw rate is how fast the output of an Op-amp can change.

The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' factor into the circuit C. shape the linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit

Description : The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' ... linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit

Last Answer : Answer: A

What are the methods to improve slew rate?

Description : What are the methods to improve slew rate?

Last Answer : a. The slew rate can be improved with higher closed-loop gain and dc supply voltage. But the slew rate also varies with temperature. i.e., slew rate decreases with increase in temperature. b. Another ... a higher slew rate, op-amp should have either a higher current or a small value of capacitor.

How can the slew rate be made faster?

Description : How can the slew rate be made faster?

Last Answer : The slew rate can be made faster by having a high charging current or a small capacitance value.

An infinite slew rate refers to A. no time delay B. small time delay C. large time delay D. variable time delay

Description : An infinite slew rate refers to A. no time delay B. small time delay C. large time delay D. variable time delay

Last Answer : no time delay

What causes slew rate?

Description : What causes slew rate?

Last Answer : There is a capacitor with-in or outside of an op-amp to prevent oscillation. The capacitor which prevents the output voltage from responding immediately to a fast changing input.

When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output:

Description : When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: (1) Has no offset (2) Approaches to triangular waveshape (3) Is pure sinusoidal (4) Is square wave 

Last Answer : When the initial slope of input sine wave is greater than the slew rate of an OPAMP, the output: Approaches to triangular waveshape

Slew rate is defined by:

Description : Slew rate is defined by: (1) di/dt(max) (2) dv/dt(max) (3) di/dt(min) (4) dv/dt(min) 

Last Answer : Slew rate is defined by: dv/dt(max) 

A 100 pF capacitor has a maximum charging current of 150 μA.What is the slew rate ?

Description : A 100 pF capacitor has a maximum charging current of 150 μA.What is the slew rate ? (A) 1.5 V/μs (B) 1.05 V/μs (C) 0.15mV/s (D) 10.5 mV/s

Last Answer : A 100 pF capacitor has a maximum charging current of 150 μA.What is the slew rate ? (A) 1.5 V/μs (B) 1.05 V/μs (C) 0.15mV/s (D) 10.5 mV/s

An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave ...

Description : An OP amp has a slew rate of 1V/µs. At a signal frequency of 0.1 MHz, the maximum undistorted sine wave amplitude is (a) 8V (b) 4.82 V (c) 2.02 V (d) 1.592 V

Last Answer : Slew rate = 2πfv where v is the amplitude V=(1/2π*0.1) = 1.592V

feature of PMMC instrument.

Description : feature of PMMC instrument. 

Last Answer : Consumes less power Great accuracy. High torque to weight ratio

List two advantages of platinum resistance thermometer.

Description : List two advantages of platinum resistance thermometer.

Last Answer : 1. The platinum resistance thermometer is stable 2. It is resistant to corrosion 3. It is resistant to oxidation

Differentiate between active and passive transducers

Description : Differentiate between active and passive transducers

Last Answer : Active Transducer:- A transducer which do not requires external energy source to convert signal from one form to another. Active transducers passes gain. e.g. Thermometer,Thermocuople, bourdon tubes, ... other form. Passive transducer passes loss. e.g. Thermistor, strain gauges, LVDT etc .

State the effect of dead zone on instruments.

Description : State the effect of dead zone on instruments.

Last Answer : It is the largest change in input during which the output remains constant. So during dead zone, even if input changes, output remains the same.

Difference between repeatability and reproducibility

Description : Difference between repeatability and reproducibility

Last Answer : Repeatability Reproducibility It is the degree of closeness with which a given input value is repeatedly measured. It is the degree of closeness with which a given input value is repeatedly measured . ... given period of time It is random in nature It is not random in nature

Gorillagate: How many of you would have none of the slew of objections regarding the matter had it been your child?

Description : Gorillagate: How many of you would have none of the slew of objections regarding the matter had it been your child?

Last Answer : I’d sue if the zoo wouldn’t let me in the cage so I could achieve closure by taking a memorial selfie of me holding my child while he gave the “sleeping” gorilla a “good night” hug.

Should I wait for Verizon to release a slew of new phones in the next two months or give in and get the enV3 right now?

Description : Should I wait for Verizon to release a slew of new phones in the next two months or give in and get the enV3 right now?

Last Answer : There’s always gonna be something better 2 months from now. The question is, does this phone do what you want it to at a price/terms you’re comfortable with. If so, then get it. And don’t look back.

Hostgator exclusive offer that delivers some of the best shared hosting features we've seen for a very slew of freebies like domain names, SSLits a bit cheaper then Ht tps://yazing.co m/deals/hostgator/getthemoney(take spaces out and click)?

Description : Hostgator exclusive offer that delivers some of the best shared hosting features we've seen for a very slew of freebies like domain names, SSLits a bit cheaper then Ht tps://yazing.co m/deals/hostgator/getthemoney(take spaces out and click)?

Last Answer : يجعل HostGator استضافة الويب غير المحدودة سهلة وبأسعار معقولة مع مساحة قرص غير محدودة وعرض النطاق الترددي ولوحة تحكم سهلة. تجعل الأسعار المنخفضة والإعداد السهل HostGator واحدة من شركات استضافة الويب الرائدة في الصناعة!2u.pw/L1LzC

Who slew the giant who had 6fingers on each hand and 6 toes on each foot?

Description : Who slew the giant who had 6fingers on each hand and 6 toes on each foot?

Last Answer : Don't know

As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay #6 C. the RPM 'function generator' and 'thrust levers' have no control D. the 'E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Description : As shown in the illustration, when the 'speed control' system is in 'SPLIT' _______________. EL-0096 A. Relays #1, #5 and #8 are not used B. the 'slew rated controller' is grounded through Relay ... E/P converters' are bypassed and air is fed directly to the governors via the 'load sharing valve'

Last Answer : Answer: C

At locations where access to the new bridge construction is available by rail, the launching of girders upto 18.3 m which method is ideal. a) slew in slew out method b) gantry method c) Launching of girders with the help of a BFR*: d) Pantoon method

Description : At locations where access to the new bridge construction is available by rail, the launching of girders upto 18.3 m which method is ideal. a) slew in slew out method b) gantry method c) Launching of girders with the help of a BFR*: d) Pantoon method

Last Answer : c) Launching of girders with the help of a