Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter.

Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter. 
by

1 Answer

Answer :

Fluorescent lamp:-

image


Operation:- When switch is ON current flows through the choke-filament no1- starter-filament no. 2- to neutral, At that time choke induces high voltage which is applied to two filaments and ionized gas, Due to this there will be high voltage ionization so that light will be emitted through the tube. Choke is acting as ballast starter is used for make and break the circuit. To operate the fluorescent lamp, need a ballast (choke) to limit the current & provide the necessary starting voltage and starter for starting the tube. 


OR 


 i) Choke: For providing high voltage at the time of starting. ii) Starter: To make and break the circuit to start the tube. 

by

Related questions

Illustrate with neat wiring diagram a single lamp control by two point method.

Description : Illustrate with neat wiring diagram a single lamp control by two point method.

Last Answer : Single lamp control by two point method:  This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the ... the person will change the position of switch S2, so that the lamp will be switched OFF'.

Explain the working of Neon sign tube with diagram.

Description : Explain the working of Neon sign tube with diagram.

Last Answer : Neon sign tube: The construction & circuit diagram for neon tube is as shown in fig. Basically neon tube is used for advertisement or decoration purpose. The maximum length of tube is ... the HT transformer must be earthed separately. * Caution notice of danger board is required.

The effective resistance of an iron-cored choke working on ordinary supply frequency...

Description : The effective resistance of an iron-cored choke working on ordinary supply frequency is more than its true resistance because of?

Last Answer : The effective resistance of an iron-cored choke working on ordinary supply frequency is more than its true resistance because of iron loss in core.

How to Do a Triangle Choke

Description : How to Do a Triangle Choke

Last Answer : How to Do a Triangle Choke In judo and jiu-jitsu, chokes are an important part of self-defense and high-level competition. One of the more flamboyant and effective chokes in the grappling arts is ... now start to master one of the most flashy and dangerous choking manuevers in all of martial arts.

Why can't you use dimmers with fluorescent or halogen lights?

Description : Why can't you use dimmers with fluorescent or halogen lights?

Last Answer : answer:Regular lightbulbs have metal (e.g. Tungsten) filaments in them. With a dimmer, you can alter the amount of electricity (trying to keep it simple) going through them. As much electricity goes ... thing-and they are sometimes noisy. Hope this helps and that it was what you were looking for.

How to Replace a Fluorescent Light Ballast ?

Description : How to Replace a Fluorescent Light Ballast ?

Last Answer : How to Replace a Fluorescent Light Ballast You can count on fluorescent bulbs to shine brightly for different areas in your home, but they need to be replaced every now and then. Sometimes though, the ... time by replacing the ballast. Just follow these easy tips and you'll do this in no time.

Draw the constructional detail of C type bourdon tube and explain its working.

Description : Draw the constructional detail of C type bourdon tube and explain its working. 

Last Answer : Explanation : The C-shaped Bourdon tube has a hollow, elliptical cross section. It is closed at one end and is connected to the fluid pressure at the other end. When pressure is applied, ... the maximum operating pressure of the system or portion of the system in which the gauge is installed. 

Why the choke is used with tube light?

Description : Why the choke is used with tube light?

Last Answer : Ans. Choke is used as inductance and check voltage surge at starting and limit the current in Running.

Why starter is used in flourescent tube?

Description : Why starter is used in flourescent tube?

Last Answer : Ans. Starter is used in flourescent tube for automatic make & break in the circuit for starting purpose. It generates voltage in choke to aid in series with supply so as to stabilize gas discharge in Flourescent tubes.

Draw and describe construction and working of Bourdon tube.

Description : Draw and describe construction and working of Bourdon tube.

Last Answer : Construction and working : C type bourdon tube is made up of an elliptically flattened tube bent in such a way as to produce the C' shape as shown in the figure. One end (free ... displacement can be indication of applied pressure. Accuracy of this element is higher than C' type element.

what is the difference between four point starter and three point starter?

Description : what is the difference between four point starter and three point starter?

Last Answer : The shunt connection in four point starter is provided separately form the line where as in three point starter it is connected with line which is the drawback in three point starter.

Compare casing capping wiring with concealed wiring.

Description : Compare casing capping wiring with concealed wiring.

Last Answer : Compare casing capping wiring with concealed wiring: 

State different types of holders used in wiring installation.

Description : State different types of holders used in wiring installation.

Last Answer : Following types of holders used in wiring installation: 1. Pendent Holder 2. Batten Holder 3. Angle holder 4. Screwed holder 

Name safety tools used in industry for electrical wiring.

Description : Name safety tools used in industry for electrical wiring.

Last Answer : Safety tools used in industry for electrical wiring : 1) Hand gloves 2) Goggles 3) Rubber mats 4) Fire extinguishers 5) Danger notice plates 6) Search lights 7) Safety shoes or Gumboots 8) Ear plugs ... belts 13) Safety mask 14) Fire buckets 15) First aid box 16) Insulating stick or discharge rod

Explain the necessity of starter for D.C. motor. State various types of D.C. motor starter.

Description : Explain the necessity of starter for D.C. motor. State various types of D.C. motor starter. 

Last Answer : Necessity of Starter for D.C. Motor: Armature current is given by equation Ia = (V−Eb)/Ra i) If the motor is at standstill or rest, back emf Eb is zero (as Eb= ZNP/(60A), at start speed N ... . Types of D.C. motor starters: i) Two point starter ii)Three point starter iii) Four point starter

Draw block diagram for CNC drilling machine and explain its working.

Description : Draw block diagram for CNC drilling machine and explain its working.

Last Answer : Block diagram consist of the following points:  Machine tool with DC servo motor as feedback element. The transducer is added as adaptive control application.  The auxiliary controller ... line.  The interrupt pulses are generated by TBG and supplied to computer through inter

Draw the circuit diagram of crystal oscillator and explain its working.

Description : Draw the circuit diagram of crystal oscillator and explain its working.

Last Answer : To excite a crystal for operation in the series-resonant mode it may be connected as a series element in a feedback path, the crystal impedance is the smallest and the amount of positive feedback is the largest. ... which is good.  The resonant frequency is given as  Fo = 1/( 2 π √LC ) 

How to Replace a Starter

Description : How to Replace a Starter

Last Answer : How to Replace a Starter The starter is where it all begins. Your car is just sitting there and ready to go, but it won't. A charge is supposed to be sent to the starter and then ... the battery and tighten the connection. Start the engine to make sure that all connections have been made properly.

State any four advantages of soft starter.

Description : State any four advantages of soft starter.

Last Answer : Advantages of soft starter: 1. Very low line voltage drops on motor operation 2. Reduced energy losses in the lines 3. System efficiency increases 4. Very smooth starting & operation 5. As ... may lead to lower MD billing. 13. Less mechanical maintenance. 14. Saving in operating costs.

State function of starter and ELCB. (Earth Leakage Circuit Breaker)

Description : State function of starter and ELCB. (Earth Leakage Circuit Breaker)

Last Answer : i) Function of Starter:- 1. To prevent the high starting current OR to minimize the starting current. 2. To give supply failure protection 3. To give over load and short circuit protection ... an installation and cut off the circuit from power supply and avoid electrical shock to the person.

In a manual shunt motor starter?

Last Answer : In a manual shunt motor starter over load relay is connected in series and no volt relay in parallel with the load.

Three point starter can be used for?

Last Answer : Three point starter can be used for both shunt and compound motor.

A three point starter is considered suitable for?

Last Answer : A three point starter is considered suitable for shunt as well as compound motors.

A direct online starter is used for starting motors?

Last Answer : A direct online starter is used for starting motors up to 5 H.P.

For starting a D.C. motor a starter is required because?

Last Answer : For starting a D.C. motor a starter is required because it limits the starting current to a safe value.

Sound Technical advice for wiring a room that already has a sconce light for a ceiling fixture?

Description : Sound Technical advice for wiring a room that already has a sconce light for a ceiling fixture?

Last Answer : If the wall is an interior wall then it should be an empty cavity. If it is an old home you may have fire stops inside the walls that will be a dead end when you attempt to fish the wire down. Make ... a good idea to know how much load is already on the circuit if you want to still use the sconce.

Wiring – types

Description : Wiring – types

Last Answer : Ans) a. Casing & Capping b. Concealed wiring c. Cleat Wiring d. Conduit Wiring – Cutting of wall.

How to replace the electrical wiring in the apartment?

Description : How to replace the electrical wiring in the apartment?

Last Answer : How to replace the electrical wiring in the apartment? In most cases, when renovating an apartment, a complete replacement of the electrical wiring is required, especially if the house was built in ... Upon completion of the finishing, the new electrical wiring in your apartment is ready for use.

List any four wiring accessories and its function.

Description : List any four wiring accessories and its function. 

Last Answer : Following wiring accessories: 1) Lamp holder: It is the holding accessory. The different types of holders used such as angle holder, batten holder, pendent holder 2) Ceiling Rose: Ceiling rose are of two types: ... etc 9) Switch board, ICDP Main Switch 10) All types of size of VIR & PVC wire

List the types of Internal wiring in residential installations –

Description : List the types of Internal wiring in residential installations –

Last Answer : 1) Cleat wiring 2) Batten wiring 3) Wooden casing capping wiring 4) PVC conduit wiring 5) PVC casing capping wiring 6) Concealed wiring

Draw Bourdon tube with LVDT setup for pressure measurement.

Description : Draw Bourdon tube with LVDT setup for pressure measurement.

Last Answer : Bourdon tube with LVDT setup for pressure measurement.

Draw the circuit diagram of battery charger using SCR and explain it’s working.

Description : Draw the circuit diagram of battery charger using SCR and explain it’s working.

Last Answer : Battery charger circuit using SCR: The figure shows the battery charger circuit using SCR. A 12V discharged battery is connected in the circuit and switch SW is closed. The singlephase 230V ... not fired. In this way, after full charging, further charging is automatically stopped.

Draw the block diagram of satellite sub-system and explain power subsystem.

Description : Draw the block diagram of satellite sub-system and explain power subsystem.

Last Answer : POWER SUBSYSTEM- This system provides the necessary DC power to the satellite. All communication satellites derive their electrical power from solar cells. There is also a battery backup facility used during ... . to d.c. converter is used to raise the level of low voltages to high voltage.

Draw and explain Hartley Oscillator circuit diagram.

Description : Draw and explain Hartley Oscillator circuit diagram.

Last Answer : Function of each component: 1. An NPN transistor connected in a common emitter configuration works as the active device in amplifier stage and CE configuration provides 180°phase shift. 2. R1 and R2 ... circuit to the base-emitter circuit.  The frequency of oscillation is given as-  

Distinguish between fire tube and water tube boilers in steam power plant.

Description : Distinguish between fire tube and water tube boilers in steam power plant.

Last Answer : Fire Tube boiler Water Tube boiler In fire tube boilers hot gases are passed through the tubes and water surrounds these tubes. In these boilers water is inside the tubes and hot gases are ... risk of explosion due to low pressure. Risk of explosion is more due to high pressure.

what is vacuum tube?

Description : what is vacuum tube?

Last Answer : A vacuum tube is a tube with no air particles.

Draw block diagram of instrumentation system. State function.

Description : Draw block diagram of instrumentation system. State function.

Last Answer : Primary transducer: The sensor which comes in contact with the measurement medium to sense the quantity. Variable conversion element: the transducer which converts the sensor ... transmitted through suitable transmission medium to the operator or presented with the help of indicators.

Draw the block diagram of basic wind energy conversion system and write function of each block.

Description : Draw the block diagram of basic wind energy conversion system and write function of each block. 

Last Answer : Block diagram of basic wind energy conversion system: OR Components of wind power plant and their functions:  1) Rotor /Blade/Aero-turbine: Blade extracts significant power from the ... stronger and smoother. Towers are supports to raise the main part of the turbine up in the air.

Draw a block diagram of electronic energy meter. Write function of each block.

Description : Draw a block diagram of electronic energy meter. Write function of each block.

Last Answer : Electronic Energymeter  Functions of components/blocks: - CT reduces current to reasonable value for current scaling network. - Voltage & current scaling networks reduce proportionally the voltage ... ADC converts the square wave frequency analog output to display the energy in watthour.

Draw block diagram of CRO. Write function of each block.

Description : Draw block diagram of CRO. Write function of each block.

Last Answer : 1. Vertical amplifier strengthens the input signal applied to vertical depleting plates 2. Trigger circuit gives input to time base circuit 3. The output of time base generator is amplified by ... of CRT internally coated with Phosphors material on which we observe waveform of the input signal.

Explain with neat diagram the working of photo-voltaic cell.

Description : Explain with neat diagram the working of photo-voltaic cell. 

Last Answer : Diagram the working of photo-voltaic cell: Working:- Solar cell operates on principle of Photo-voltaic effect    Solar cell works in following steps: The solar cell is composed ... . When you connect loads such as a light bulb, electric current flows between the two electrodes.  

Explain construction & working of attraction type M.I. instrument with neat diagram.

Description : Explain construction & working of attraction type M.I. instrument with neat diagram.

Last Answer : 1. Moving element: a small piece of soft iron in the form of a vane or rod.  2. In Attracted type a cylindrical coil or solenoid which is kept fixed. An oval-shaped soft-iron piece are ...   9. When = the pointer will be stable & we can get correct reading of the electrical quantity

Draw the labeled block diagram of process control system and explain each block.

Description : Draw the labeled block diagram of process control system and explain each block.

Last Answer : Explanation - Process control system consists of process or plant, sensor, error detector, automatic Controller, actuator or control element. 1) Process or plant- process means some manufacturing sequence ... process which changes the process variable. Output of this block is denoted by u .

Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Description : Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Last Answer : Operation:  The FM signal which is to be demodulated is applied at the input of the PLL.  the PLL is locked to the FM  The error voltage produced at ... using PLL ensures a high Linearity, between the instantaneous input frequency and VCO control voltage (error amplifier output)

A tube light rated 50 watts (electric powers) is used for 10 hours per day for 30 days in a month. How much electric energy is being consumed by it per month? Similary per year, how much energy will be consumed?

Description : A tube light rated 50 watts (electric powers) is used for 10 hours per day for 30 days in a month. How much electric energy is being consumed by it per month? Similary per year, how much energy will be consumed?

Last Answer : Ans. 50 x 10 x 30 = 15000watts = 15000/1000= 15 units per month. Per units consumed: 15X12= 180units per year.

How to Change a Bike Tire Tube

Description : How to Change a Bike Tire Tube

Last Answer : How to Change a Bike Tire Tube For any bicycle user, knowing how to change bike tires and bike tubes are essential when you run into a flat tire. Here are the things you need to keep at hand and the ... fully, which typically takes 40 psi. Give the bike tire another look-over, and you're good to go.

How to Patch an Inner Tube ?

Description : How to Patch an Inner Tube ?

Last Answer : How to Patch an Inner Tube Bicycle tires are meant to last and withstand the strains of rough riding, although they can be punctured, worn, or damaged. It can be quite expensive to replace the inner ... you have patched an inner tube, it's very important to have it replaced as soon as possible.

The pressure and velocity at the throat of a Venturi tube, measuring the flow of a liquid, are related to the

Description : The pressure and velocity at the throat of a Venturi tube, measuring the flow of a liquid, are related to the upstream pressure and velocity, respectively, as follows: (A) Pressure is lower but ... velocity is lower (C) Both pressure and velocity are lower (D) Pressure and velocity are identical

Last Answer : The pressure and velocity at the throat of a Venturi tube, measuring the flow of a liquid, are related to the upstream pressure and velocity, respectively, as follows: (A) Pressure is lower but ... lower (C) Both pressure and velocity are lower (D) Pressure and velocity are identical

What is Cathode ray tube ?

Description : What is Cathode ray tube ?

Last Answer : Cathode ray tube (CRT) is a vacuum tube using cathode rays to generate a picture on a fluorescent screen. These cathode rays are in fact the electron beam deflected and modulated, which impinges on a ... tube used to display data in a visual form. Picture tube of a television or computer terminal.