Define the following terms : (i) Base Station (ii) Control Channel (iii) Mobile Station (iv) Page

Define the following terms : (i) Base Station (ii) Control Channel (iii) Mobile Station (iv) Page 
by

1 Answer

Answer :

i) Base Station: – A fixed station in a mobile radio system used for radio communication with mobile stations. Base stations are located at the center or on the edge of a coverage region and consist of radio channels and transmitter and receiver antennas mounted on a tower. 

ii) Control Channel: Control channel: It is defined as the radio channel used for the transmission of beacons such as call set up, call request, call initiation as well as the control information. 

iii) Mobile Station: Mobile station: It is defined as a station in the cellular radio service which is used when in motion at an unspecified location. Mobile stations can be portable hand held personal units or they can be the ones installed in vehicles. 

iv) Page: A message is sent to a paging subscriber via the paging system access number with a telephone keypad or modem. The issued message is called a „Page‟. The paging system then transmits the page throughout the service area using base stations which broadcast the page on a radio carrier.
by

Related questions

State the function of following components of a nuclear power station: i) Moderator ii) Shielding iii) Control rod iv) Coolant

Description : State the function of following components of a nuclear power station: i) Moderator ii) Shielding iii) Control rod iv) Coolant 

Last Answer : i) Function of Moderator :- Moderator is to moderate or reduce the speed of fast neutron to help the fission process.  ii) Function of sheilding : Shielding is to protect environment, ... from reactor core and transfer it in heat exchanger for producing steam at high pressure and temperature. 

Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Description : Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Last Answer : Parts Insulating Materials  Insulation between heating element and base plate of electric iron. Mica Insulation used over copper or aluminium conductor used for making coils.  ... Transformer bushings Porcelain  Insulation between transmission line and pole. Porcelain

lf the wire which is vertical to this page has electron flow downwards the conductor will have

Description : lf the wire which is vertical to this page has electron flow downwards the conductor will have

Last Answer : lf the wire which is vertical to this page has electron flow downwards the conductor will have a counter-clockwise field in the plane of the paper

How to Cite a Web Page

Description : How to Cite a Web Page

Last Answer : How to Cite a Web Page Thanks to the Internet, many online sources can now be used in academic tasks like term papers, theses, and dissertations. Citing a Web page can be problematic ... . With these steps, you can easily cite Web pages and maintain scholarly integrity and intellectual honesty.

Describe IS – 95 forward link channel structure.

Description : Describe IS – 95 forward link channel structure.

Last Answer : The IS-95 forward Channel structure consists of four types of logical Channels - pilot Channel, synchronization Channel, paging Channel, and forward traffic Channels. Each forward carrier Channel contains one ... . This code is known as the channel identifier. This code is different for each user

Compare base load plant with peak load plant on any two points.

Description : Compare base load plant with peak load plant on any two points.

Last Answer : Points Base load plant Peak load plant Definition The power plant which supplies base load of load curve is known as base load plant  The power plant which supplies ... ,thermal,nuclear power station Small capacity storage hydro,pumped storage hydro,gas,diesel power station.

State why nuclear power plants are used as base load plants and diesel power plants as a peak load plant.

Description : State why nuclear power plants are used as base load plants and diesel power plants as a peak load plant. 

Last Answer : 1. Because of following points Nuclear power plant used as base load power plant:-  1. Nuclear power plants is very economical for producing bulk amount of electric power 2. Nuclear power plant is reliable ... . The plants can be put on load easily. 4. Diesel engines take less time to make OFF.

Explain estimation of channel capacitance of CMOS.

Description : Explain estimation of channel capacitance of CMOS.

Last Answer : Capacitance estimation: The dynamic response i.e. switching speed of MOS system depends on capacitance associated with the MOS devices which are formed by different layers in MOS transistors ... are due to three dimensional, distributed charge voltage relations within the device structure. 

What is the channel capacity of a noisy channel with conditional probability of error p = 1/2?

Description : What is the channel capacity of a noisy channel with conditional probability of error p = 1/2? A) 0 B) 1 C) Infinity D) 2  

Last Answer : What is the channel capacity of a noisy channel with conditional probability of error p = 1/2?  A) 0 B) 1 C) Infinity D) 2  

As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel

Description : As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by (symbols/notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2 

Last Answer : As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by ( ... /notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2 

The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at

Description : The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at a gate voltage of 3V. Pinch off would be occurs at a drain voltage of (A) 1.5V (B) 2.5V (C) 3.5V (D) 4.5V

Last Answer : The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at a gate voltage of 3V. Pinch off would be occurs at a drain voltage of 2.5V

What is channel length modulation in MOSFET?

Description : What is channel length modulation in MOSFET?

Last Answer : Shortening of lenght of the inverted channel region with increase in drain bias for large drain biases due to which current increases with drain bias and output resistance decreases is called channel length modulation in MOSFET.

The transit time of the current carriers through the channel of a JFET decides it's ?

Description : The transit time of the current carriers through the channel of a JFET decides it's?

Last Answer : The transit time of the current carriers through the channel of a JFET decides it's gate characteristics.

How to Steal a Base

Description : How to Steal a Base

Last Answer : How to Steal a Base One of the most exciting things about baseball is stealing bases. With proper timing and good skills, you'll be able to go from one base to another without so much effort. Here ... eventually have our own way of stealing a base, but for now, you can stick to these basic steps.

If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be

Description :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be A) 0.98 B) 0.41 C) 59 D) 55  

Last Answer :  If the base current of a BJT is 250 µA and emitter current is 15 mA, then the common base current gain will be 0.98 

What are the seven base units?

Description : What are the seven base units?

Last Answer : Length, mass, time, electric current, temperature, luminous intensity and amount of substance are the seven base units.

The time base signal in Cathode Ray Oscilloscope (CRO) is

Description : The time base signal in Cathode Ray Oscilloscope (CRO) is  (1) A square wave signal (2) A sawtooth signal (3) A triangular wave signal (4) A sinusoidal signal

Last Answer : 2 Saw tooth 

_______ is invariably used as base load plant.

Last Answer : Nuclear power plant is invariably used as base load plant.

How often do you change the wallpaper on your mobile phone?

Description : How often do you change the wallpaper on your mobile phone?

Last Answer : Once a year, if I remember.

Do you have any fitness related app installed on your mobile?

Description : Do you have any fitness related app installed on your mobile?

Last Answer : answer:Myfitnesspal is good. I log the food I consume and the exercise I do. I also have Garmin Connect that syncs with my watch. I also have a few productivity apps (such as Routinely) where ... particularly related to fitness but help me track whether I'm being a lazy slob or doing some exercise.

AT&T mobile to mobile texting?

Description : AT&T mobile to mobile texting?

Last Answer : no

Is there a web messenger that can contact offline or mobile contacts?

Description : Is there a web messenger that can contact offline or mobile contacts?

Last Answer : I believe that most of them can. AIM has a web messenger, AIM Express, that does it. I think MSN messenger and Yahoo! messenger can do it as well.

which rectifier used in mobile charger?

Last Answer : Full wave bridge rectifier is used in mobile chqrger.

wireless mobile charger

Description : wireless mobile charger

Last Answer : it is simply the wireless transfer of the electricity such in transformer the EMF is induced in the neighbouring called because of change in the voltage in primary coil show the phenomenon of mutual inductance is at a very high level and energy can transfer in through the air or another medium

Sketch block diagram of satellite earth station and state functions of each block

Description : Sketch block diagram of satellite earth station and state functions of each block

Last Answer : The figure below shows the general block diagram of an earth station capable of transmission, reception and antenna tracking. The following are the major subsystems of ... , possible monitoring of satellite characteristics and occasionally for the measurement of special characteristics. 

Compare the Nuclear power station with Hydro power station.

Description : Compare the Nuclear power station with Hydro power station. 

Last Answer : SR. No.  Points Nuclear Power plant  Hydro Power station  1 Site/ Location Where there is ample supply of water is available, away from thickly populated areas to avoid radioactive ... Field Application As base load  Used as base load during as well as peak load 

Classify condensers used in thermal power station. Explain each type in brief.

Description : Classify condensers used in thermal power station. Explain each type in brief. 

Last Answer : Types of condenser: Classification: 1. Jet Condenser (Mixing Type) 2. Surface condenser (non Mixing type)  Explanation:-   1. Jet Condenser (Mixing Type) In Jet condenser the steam ... there in no direct contact between the steam and cooling water. This condensate is reused in boiler. 

Explain the working of Hydro power station with schematic layout.

Description : Explain the working of Hydro power station with schematic layout. 

Last Answer : Working of Hydro- Electric Power Plant: Water stored at high level by constructing dam across river. This stored water has potential energy. This stored water is passed to run the water ... energy and Alternator is coupled to water turbine which converts mechanical energy into electrical energy. 

"Efficiency of thermal power station is low". — Justify.

Description : "Efficiency of thermal power station is low". — Justify. 

Last Answer : Justification: Efficiency of thermal power station is low":- Overall efficiency of T.P.P depends upon efficiency of boiler, turbine and alternator. The heat produced due to combustion of coal ... losses in thermal power plant is 71%, So efficiency of thermal power plant is less about 29% 

Applications of Diesel power station

Description : Applications of Diesel power station

Last Answer : Applications of Diesel Power Station:  1. It can be used as a standby (emergency) power plant to maintain continuity of supply. (Incase failure of main supply like hospital, Telephone exchange Radio ... 10. Diesel plants are widely used for generating power ranging from 100 to 5,000 H.P. 

List out main components of Diesel power station.

Description : List out main components of Diesel power station. 

Last Answer : Main components of Diesel power station: 1) Diesel Engine 2) Engine Air intake system 3) Engine Fuel System 4) Engine Exhaust system 5) Engine cooling system 6) Engine Lubricating system 7) Engine Starting system 8) Diesel Engine Generator (Alternator) 

State the types of radioactive waste generated in a nuclear power station. Explain the methods employed for their disposal.

Description : State the types of radioactive waste generated in a nuclear power station. Explain the methods employed for their disposal.

Last Answer : Types of radioactive waste: The waste produced in nuclear power plant is in the form of solid, liquid & gases, 1. Solid Waste Disposal:-  Solid wastes removed from the reactor are very ... are measured. If it is safe then released to atmosphere at high level through large height chimney.

"Hydro electric power station are not perennial power station". Justify.

Description : "Hydro electric power station are not perennial power station". Justify.

Last Answer : Justification: The water utilized by the hydro power plants comes mostly from storage dams/reservoirs which get filled up during the monsoon rainy season. Such reservoirs are utilized for supplying ... are important. Hence "Hydro electric power stations are not perennial power station" 

List and state any four limitations of inter connected power station.

Description : List and state any four limitations of inter connected power station.

Last Answer : Limitations of inter connected power station:- 1) Initial cost of infrastructure of transmission line increases as length increases. 2) Interconnection required more automation which increases cost on ... capacity. But in absence of surplus power merits of interconnection cannot be obtain.

State the functions of fuel system and exhaust system of a diesel power station.

Description : State the functions of fuel system and exhaust system of a diesel power station.

Last Answer : Fuel system: It supplies fuel to engine for combustion purpose. It consists of Fuel Pump: - It supplies fuel to engine for combustion purpose. Strainer: - Are provided to remove suspended impurities and ... most of the noise. Chimney:- To exhaust gases in the atmosphere as high as possible. 

State the function of cooling tower and condenser in thermal power station.

Description : State the function of cooling tower and condenser in thermal power station.

Last Answer : 1. Condenser:   Function of condenser is to convert exhaust steam again into water by reducing its temperature with the help of cold water. Also it reduces back pressure of steam turbine 2 ... tower : The function of cooling tower is to reduce the temperature of water coming from condenser.

State the purpose of surge tank and spill way in hydroelectric power station.

Description : State the purpose of surge tank and spill way in hydroelectric power station.

Last Answer : Surge tank :- A surge tank is the small reservoir or tank. It is open at the top. It is installed near Vale house of turbine. It avoids water hammer effect when load on turbine reduces. (It ... ; during floods etc. In this way spill way avoids damage of dam due to excess pressure of water.

State any four factors governing Selection of site for thermal power station.

Description : State any four factors governing Selection of site for thermal power station. 

Last Answer : Following Factors are to be considered:- 1. It should locate near coal mine. 2. Sufficient quantity of water should be available. 3. Sufficient large space should be available. 4. It should be located ... laws of the land and the town planning. 14. The interests of national defense must be served.

Write down any two advantages of nuclear power station.

Description : Write down any two advantages of nuclear power station.

Last Answer : Advantages of nuclear power station :-  1) Fuel required: Fuel requirment of Nuclear Power Plant is less than Thermal Power Plant. So it reduces transportation cost of fuel and space required for fuel storage ... By use of nuclear fuel.,it saves the other fossile fuels like-coal, gas, oil, etc.

What are the maintenance schedules of a pumping station and type of starters?

Description : What are the maintenance schedules of a pumping station and type of starters?

Last Answer : Ans. Following are maintenance schedule of the pumping installation: Switch gear in every quarter and the motor & pump section every half yearly. Starters are DOL starter, star delta starter, Auto T/F starter.

How Do I Build a Low Power FM Radio Station?

Description : How Do I Build a Low Power FM Radio Station?

Last Answer : How Do I Build a Low Power FM Radio Station? A low power FM radio station offers individuals or small groups the ability to go on the air and communicate with the general public using FM radio ... FCC or your local government to determine which, if any FM frequencies you are allowed to transmit on.

Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW

Description : Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW then annual energy production is  (1) 122.8 GWh (2) 198.55 GWh (3) 128.2 GWh (4) 188.82 GWh

Last Answer : Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW then annual energy production is 122.8 GWh

For high value of diversity factor, a power station of given installed capacity will be in a position to supply?

Last Answer : For high value of diversity factor, a power station of given installed capacity will be in a position to supply more number of consumers.

Load factor of a power station is generally?

Last Answer : Load factor of a power station is generally less than unity.

Load factor of a power station is defined as?

Last Answer : Load factor of a power station is defined as average load/maximum demand.

For the protection of power station buildings against direct strokes the requirements are?

Last Answer : For the protection of power station buildings against direct strokes the requirements are interception, conduction and dissipation.

How does battery saver functionality work?

Description : How does battery saver functionality work?

Last Answer : Well I'm not sure about android (if you are using an android operating smart phone). I use the iPhone myself and it has the low battery mode. What it does essentially is it only uses data when you ... are reduced or turned off. I'm assuming other phones such as Samsung, LG, HTC etc is quite similar.

Which version of ask-public do you prefer?

Description : Which version of ask-public do you prefer?

Last Answer : Desktop. I don’t have a phone, so mobile mode makes everything all big and you have to scroll down for like seven years before reaching the bottom.

How can we develop a software that would only work if its in the hand of its original user, using the finger print technology, so that if it gets stolen or if anyone else tries to use it, they would not be able to do so?

Description : How can we develop a software that would only work if its in the hand of its original user, using the finger print technology, so that if it gets stolen or if anyone else tries to use it, they would not be able to do so?

Last Answer : If you have to ask…

What are the disadvantages of Open loop control system?

Description : What are the disadvantages of Open loop control system?

Last Answer : Open loop control system are less reliable. In open loop control system Optimization is not possible. Open loop control system are less accurate.