Draw block diagram of CNC system and state function of each block.

1 Answer

Answer :

image


(i) Input Devices: These are the devices which are used to input the part program in the CNC machine. There are three commonly used input devices and these are punch tape reader, magnetic tape reader and computer via RS-232-C communication. 


(ii) Machine Control Unit (MCU): It is the heart of the CNC machine. It performs all the controlling action of the CNC machine, the various functions performed by the MCU are 

It reads the coded instructions fed into it. 

It decodes the coded instruction. 

It implements interpolation ( linear, circular and helical ) to generate axis motion commands. 

It feeds the axis motion commands to the amplifier circuits for driving the axis mechanisms. 

It receives the feedback signals of position and speed for each drive axis. 

It implements the auxiliary control functions such as coolant or spindle on/off and tool change.


(iii) Machine Tool: A CNC machine tool always has a slide table and a spindle to control of the position and speed. The machine table is controlled in X and Y axis direction and the spindle is controlled in the Z axis direction. 


(iv) Driving System: The driving system of a CNC machine consists of amplifier circuits, drive motors and ball lead screw. The MCU feeds the signals (i.e. of position and speed) of each axis to the amplifier circuits. The control signals are than augmented (increased) to actuate the drive motors. And the actuated drive motors rotate the ball lead screw to position the machine table. 


(v) Feedback System: This system consists of transducers that acts like sensors. It is also called as measuring system. It contains position and speed transducers that continuously monitor the position and speed of the cutting tool located at any instant. The MCU receives the signals from these transducers and it uses the difference between the reference signals and feedback signals to generate the control signals for correcting the position and speed errors. 


(vi) Display Unit: A monitor is used to display the programs, commands and other useful data of CNC machine. 

Related questions

Description : Draw block diagram for CNC drilling machine and explain its working.

Last Answer : Block diagram consist of the following points:  Machine tool with DC servo motor as feedback element. The transducer is added as adaptive control application.  The auxiliary controller ... line.  The interrupt pulses are generated by TBG and supplied to computer through inter

Description : Draw the block diagram of basic wind energy conversion system and write function of each block. 

Last Answer : Block diagram of basic wind energy conversion system: OR Components of wind power plant and their functions:  1) Rotor /Blade/Aero-turbine: Blade extracts significant power from the ... stronger and smoother. Towers are supports to raise the main part of the turbine up in the air.

Description : Draw block diagram of instrumentation system. State function.

Last Answer : Primary transducer: The sensor which comes in contact with the measurement medium to sense the quantity. Variable conversion element: the transducer which converts the sensor ... transmitted through suitable transmission medium to the operator or presented with the help of indicators.

Description : Draw the labeled block diagram of process control system and explain each block.

Last Answer : Explanation - Process control system consists of process or plant, sensor, error detector, automatic Controller, actuator or control element. 1) Process or plant- process means some manufacturing sequence ... process which changes the process variable. Output of this block is denoted by u .

Description : Draw block diagram of pneumatic system showing its basic components. State the functions of control value and air actuator.

Last Answer : Diagram : Control valve: - control and regulates the direction of flow and pressure etc. Air actuator: - Air cylinders and motors are used to obtain the required movements of direction flow.

Description : Draw the block diagram of an embedded system and describe the hardware units of an embedded system.

Last Answer : OR Explanation: The embedded system consist of different components embedded into it as follows: 1) Embedded Processor 2) Power supply , reset and Oscillator circuits 3) System timers 4) ... to store data and program. Following are types of memories used in embedded system.

Description : Explain the Mechatronics system with the help of block diagram and labeled the various elements. 

Last Answer : The key elements of Mechatronics systems can be classified under following categories:  Information systems  Mechanical systems  Electrical systems  Computer systems  Sensor and actuators  ... is adjusted based on generated error and again signal is given to actuators and sensors.

Description : Draw and explain integrated duration curve used in system operation. 

Last Answer : Diagram of integrated duration curve used in system operation: Explanation:  Integrated duration curve is obtained from load duration curve. It is drawn in between load on Y-axis in KW/MW and the X- ... a particular time of a day can also be shown on a curve which is called as mass curve. 

Description : Draw simple block diagram of CNC machine and describe in short.

Last Answer : (i) Input Devices: These are the devices which are used to input the part program in the CNC machine. There are three commonly used input devices and these are punch tape reader, magnetic tape ... Unit: A monitor is used to display the programs, commands and other useful data of CNC machine.

Description : Draw a neat sketch of Gating system. State the functions of any four elements.  

Last Answer : Gating system:  1. Sprue: The circular cross section that minimizes heat loss and turbulence is sprue, and the area of it is quantified from the choke area as well as the gating ratio.  2. ... the molten metal flow from the ingate has to be proportional to the casting area's volume. 

Description : Draw and explain schematic of PLC based automatic car parking barrier system.

Last Answer : Explanation: Automatic car parking system allow to park maximum numbers of car in parking zone according to size of parking zone. parking zone number of vehicle parked in parking zone is less ... available parking space then automated parking system does not allow enter next car in parking zone. 

Description : With neat circuit diagram explain working of emergency light system. 

Last Answer : Emergency lighting system:  In the residential, commercial and industrial areas, the illumination system work with available AC supply. In the event of AC supply failure, partial illumination can be ... glows. In rthis way, on failure of AC supply, light is obtained from DC supply.

Description : With a neat diagram, explain back pressure steam turbine co-generation system.

Last Answer : Back pressure steam turbine co-generation system: In this type steam enters the turbine chamber at High Pressure and expands to Low or Medium Pressure. Enthalpy difference is used for generating power / work. ... , the overall thermal efficiency of the system could reach as much as 90 percent.

Description : With neat diagram explain the following terms: (i) Steam turbine co-generation system (ii) Gas turbine co-generation system

Last Answer : (i) Steam turbine co-generation system: The two types of steam turbines most widely used are the backpressure and the extraction. Another variation of the steam turbine topping ... power. The exhaust or the extracted steam from the steam turbine provides the required thermal energy.

Description : Describe the function of MUSE system for HDTV.

Last Answer : Bandwidth can be reduced by MUSE (Multiple Sub -Nyquist Sampling Encoding) system MUSE stands for Multiple Sub-Nyquist sampling encoding and is an HDTV bandwidth compression schemedeveloped by ... digital Audio system is called DANCE (Digital Audio Near-Instantaneous Compression and expansion). 

Description : Draw a labeled block diagram of sine wave generator and state function of each block. 

Last Answer : Function Generator:  This instrument can deliver sine, triangular & square waves with frequency range of 0.01 Hz to 100 kHz.  The frequency control network is governed by a frequency ... voltage reaches a predetermined level on the negative slope of the integrator's output voltage.

Description : Draw block diagram of microprocessor and state the function of each block.

Last Answer : Registers: The 8085 includes six registers, one accumulator, and one flag register, as shown in Figure. In addition, it has two 16-bit registers: the stack pointer and the program counter. The 8085 ... , Subtraction, Increment, Decrement etc.  Logic Operations: AND, OR, X-OR, Complement etc.

Description : Draw block diagram of Data Acquisition System (DAS). Write function of each block.

Last Answer : Data Acquisition System(DAS) : - (Definition) - The function of DAS is to collect the input data efficiently, accurately, simultaneously to store and display the data. It consists of sensor or transducer ... - to output od DAS is provided in the form of display or plot or recoded in recorder.

Description : State the need of modulation in communication system.

Last Answer : Need of modulation:- 1. To reduce the height of antenna 2. To avoids mixing of signals 3. To increases the range of communication 4. To make multiplexing of maximum signal is possible 5. To improve the quality of reception

Description : Define measurement and state the significance of electrical measurement system.

Last Answer : Measurement: Measurement is essentially a process in which magnitude of a quantity is determined in comparison with another similar quantity with significant units. OR The measurement of a given ... x) The measurement conforms the validity of hypothesis and also adds to its understanding.

Description : State two advantages of digital system over analog system.

Last Answer : 1. They are less susceptible to noise. 2. The effect of fluctuation in the characteristic of the components, ageing of components etc. is very small in digital circuits. 3. Digital circuits have capability of memory which makes them suitable for computers. 4. More accurate.

Description : State the functions of fuel system and exhaust system of a diesel power station.

Last Answer : Fuel system: It supplies fuel to engine for combustion purpose. It consists of Fuel Pump: - It supplies fuel to engine for combustion purpose. Strainer: - Are provided to remove suspended impurities and ... most of the noise. Chimney:- To exhaust gases in the atmosphere as high as possible. 

Description : State any four advantages of interconnected system.

Last Answer : Advantages of interconnected Systems: i) Reduced Overall installed Capacity: Inter connected power systems reduce the overall requirement of installed capacity for a given load area. With ... to interconnection, there is optimum utilization of available natural resources in the country.

Description : State the functions of following elements: i) Diesel engine system ii) Air intake system iii) Engine exhaust system iv) Engine starting system.

Last Answer : i) Diesel engine system:-  Four strokes Two strokes ii) Air intake system:- Air intake system is provided to supply air to engine cylinder for fuel combustion.  iii) Engine exhaust system ... provided to rotate the engine initially until the firing starts and engine run under its own power. 

Description : steady-state stability of a power system is improved by

Last Answer : steady-state stability of a power system is improved by using double circuit line instead of single circuit line

Description : Draw neat block diagram of FM receiver and explain function of each block

Last Answer : Explanation:-  RF amplifier: There are two important functions of RF amplifier: 1) To increase the strength of weak RF signal. 2) To reject image frequency signal. In FM ... FM broadcast, the maximum modulating frequency is 15 kHz. Hence the audio amplifier must have large bandwidth.

Description : Draw a block diagram of electronic energy meter. Write function of each block.

Last Answer : Electronic Energymeter  Functions of components/blocks: - CT reduces current to reasonable value for current scaling network. - Voltage & current scaling networks reduce proportionally the voltage ... ADC converts the square wave frequency analog output to display the energy in watthour.

Description : Draw block diagram of CRO. Write function of each block.

Last Answer : 1. Vertical amplifier strengthens the input signal applied to vertical depleting plates 2. Trigger circuit gives input to time base circuit 3. The output of time base generator is amplified by ... of CRT internally coated with Phosphors material on which we observe waveform of the input signal.

Description : Draw the block diagram for PLC power supply and explain the function of each block.

Last Answer : PLC power supply generates the required dc voltage levels for operation of the internal circuit of PLC. It is a switched mode power supply which accepts wide range of AC/ DC input ... of power failure from AC input, Battery backup becomes active and prevents accidental shut down of PLC

Description : Draw a neat labelled diagram of PLC. Explain the function of each block.

Last Answer : Block Diagram of PLC:-  A simplified block diagram of a PLC shown in above Fig. It has three major units/sections.  I/O (Input/Output) Modules.  CPU (Central ... membrane keypad for program entry, and a display device (LED or LCD) for viewing program steps of functions. 

Description : With the help of block diagram explain closed loop control CNC system. 

Last Answer : Special motors called servos are used for executing machine movements in closed loop system. The name indicates that the closed loop control system has a loop that is closed as shown in fig. ... to the drive unit and the cycle repeats until there is no error signal from the comparator.

Description : Draw block diagram of basic electronic communication system and state the function of each block.

Last Answer : i) Input signal: - The information can be in the form of sound, picture or data coming from computer. ii) Input transducer: - it converts original information into equivalent electrical ... back to suitable form. vii) Output transducer: - It converts electrical signal into original form. 

Description : characteristics of Hi-Fi amplifier system.

Last Answer : Characteristics of HI-FI amplifier: 1. Signal to noise ratio should be better than 50dB. 2. Frequency response should be flat within +-1dB. 3. Nonlinear distortion should not be more ... provided. 6. Environmental conditions should be such as to eliminate the external noise in listening room. 

Description : DTH System

Last Answer : Outdoor unit: It consists of a receiving antenna, low noise amplifier & converter the receiving antenna is parabolic reflector with a horn as the active element. The horn can be ... fed to the normal domestic TV receiver, which after due processing reproduces picture & sound. 

Description : requirements of a distribution system

Last Answer : Following requirements of a distribution system.  1. Layout should be simple in design. 2. It should have less initial cost 3. The distribution system should have minimum distribution ... stability of existing distribution system. 15. Time required for completion of work should be less. 

Description : Why radial distribution system used for short distance ? 

Last Answer : Because of following disadvantages radial distribution system is not used for long distance:  Since there is only one feeder to DTC feed at one point so, 1) There is no reliability ... more time for fault finding & repairing Hence radial distribution system is used for short distance.

Description : vertical deflection system and explain its operation.

Last Answer : The main function of the vertical deflection system , is to provide an amplified signal of proper level to derive the vertical deflection plates without any distortion. For amplification of the ... suppression, reduced nonlinear effects because none of the plates are at ground potential.

Description : Working of Simple Vapor absorption system

Last Answer : Working of Simple Vapor absorption system:  A Simple Vapor absorption system consists of evaporator, absorber, generator, condenser, expansion valve, pump & reducing valve. In this system ammonia ... where there is scarcity of Electricity and it is very useful at partial and full load. 

Description : Write four advantages of FMS (Flexible Manufacturing System).

Last Answer : 1. Large variety of same products 2. Profitable investment. 3. Requires limited inventory. 4. Low labor cost. 5. Flexible system. 6. Speedy production. 7. Improve product quality. 

Description : List and explain the components of a hydraulic system.

Last Answer : Components Hydraulic: Hydraulic pump- Supply fluid to the components in the system. Pressure in the system develops in reaction to the load. Hence, a pump rated for 5,000 ... mechanical components and need to be removed along with other contaminants.  Seals, fittings and connections.

Description : Explain how MEMS accelerometer is used as airbag sensor for car system.

Last Answer : MEMS Accelerometer is used as airbag sensor: Mechanical ignition airbags fit inside the steering wheel pad. When a collision occurs, the inertial sensor moves, setting off a ... the airbag with wiring. This is especially effective when fitting both driver- and passenger-side airbags.

Description : What are advantages and disadvantages of Mechatronics system? 

Last Answer : Advantages of Mechatronics system:  High level of integration.  Increased functionality and better design.  More use of electronics and software instead of mechanical function.  Assumes ... Its replacement is difficult, that it is difficult to change old system to new system. 

Description : Explain in brief how anti-lock braking system works

Last Answer : An ABS is a system on motor vehicles which prevents the wheels from locking while braking stopping safely is one of the most important functions a motor vehicle can perform. Diagram: ... to decrease the pressure on the braking circuit, effectively reducing the braking force on that wheel.

Description : Differentiate between pneumatic and hydraulic system. 

Last Answer : Pneumatic System Hydraulic System 1 Pneumatic system uses gas for power transmission, after compression and it is used as medium for carrying out mechanical work. ... : In industrial applications, air conditioners Applications: In petrochemical industries, oil refineries.

Description : Describe the procedure for working of paging system.

Last Answer : Pager is a Simplex Communication Device. Paging Systems are communication systems that send messages to a subscriber. Message can be numeric or alphanumeric. Paging Systems are used to notify a subscriber ... message is sent by sender to his pager and the message will be displayed in the LCD.

Description : Why solar system is preferred now a days ? Justify your answer. 

Last Answer : Since availability of fossil fuels like coal are limited in future so there is more importance of solar power in the energy deficient because of following advantages of solar power Fuel is ... .  10. solar system technology are ideally suited to distributed applications ( Decentralized system)

Description : What are the disadvantages of Open loop control system?

Last Answer : Open loop control system are less reliable. In open loop control system Optimization is not possible. Open loop control system are less accurate.

Description : Explain starting system in diesel electric power plant.

Last Answer : Starting system in Diesel Electric Power Plant: It includes Storage battery, compressed air tanks, self-starter etc. The purpose of engine starting system is to rotate the engine initially while ... as Ammeters, Voltmeters, Wattmeters, Thermometers, Pressure gauges, Visible and audible alarm etc.

Description : Explain fuel system and air intake system in diesel electric power plant.

Last Answer : Fuel system and air intake system in diesel electric power plant :  Fuel system: It consists of storage tank, strainers, fuel transfer pump and all day fuel tank. The fuel oil is supplied ... Filters are provided to remove dust particles from air which may act as abrasive in the engine cylinder.

Description : What is the choice of size and number of generator units in interconnected power system?

Last Answer : Choice of Size and Number of Generating Units: 1. The size/rating and number of generating units in such way that they approximately match with the load curve as closely as possible. 2. In ... , if power plant is connected to grid system then generating unit of higher capacity can be installed.