Single stage CE amplifier

1 Answer

Answer :

image


Requirement(Necessity) of Multistage amplifier: -In many applications we required a high gain. But sometimes gain produced by an amplifier is not sufficient so to increase the gain, we have to connect no. of single stage amplifiers in cascade which results in multistage. The main important necessity of multistage amplifier is for providing high gain. It is also required for high bandwidth.

Related questions

Description : Compare between CB , CE & CC transistor configuration.

Last Answer : Parameter CB CE CC I/P impedance Low Or 50Ω Medium Or 600Ωto 4kΩ High Or 1 MΩ Current Gain Less than or equal to 1 High Highest Voltage Gain Medium Medium Less ... k Ω to 50 k Ω Low Or 50 Ω Phase shift between input and output 0° 360° 0° 

Description : Sketch output characteristics of CE configuration. Show all the regions.

Last Answer : Sketch output characteristics of CE configuration. Show all the regions.

Description : Is the only way to get over stage fright going on stage?

Last Answer : There are certainly ways to ease out of your fear more gradually. Practicing before a small audience, speaking in public but not on a stage, taking a public speaking or presentation skills class, and going to ... some ways that are less drastic. You don't have to climb the mountain in a single leap.

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

Description :  two stage amplifier and need of multistage amplifier.

Last Answer : Circuit diagram of two stage amplifier : Need of multistage amplifier: The output from a single stage amplifier is usually insufficient to drive an output device. So that ... to second amplifier.  To increase the overall gain of the amplifier multistage amplifier is needed.

Description : State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Last Answer : Need:- The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in order to obtain greater voltage and power gain, cascade amplifiers are used.

Description : working of class B push pull amplifier.

Last Answer : Circuit Diagram:- Operation:  In class B amplifier transistor conduct only for half cycle of input signal.One conduct in positive half cycle and other conducts in negative half ... Then output transformer joins these two halves and produces a full sine wave in the load resistor. 

Description : Compare amplifier and oscillator.

Last Answer : Figure shows a block diagram of an amplifier and an oscillator.   An amplifier is a device, which produces an output signal with similar waveform as that of the input. ... is supplied. An oscillator does not require any external signal to start or maintain energy conversion process.

Description : role of tuned LC circuit in tuned amplifier.

Last Answer : In order to pick up and amplify the desired radio frequency signal, the resistive load in the audio amplifier is replaced by a tuned circuit (also called a parallel resonant circuit)as shown ... desired radio frequency signal. (ii)Amplification of the selected signal to a suitable voltage level.

Description :  applications of RC coupled amplifier

Last Answer : Applications of RC coupled amplifier: (i) Widely used as Voltage amplifiers. (ii) They are used in Public Address System. (iii) In Tape recorders. (iv) In stereo amplifiers (v) In T.V. V.C.R. and C.D. Players.

Description : characteristics of Hi-Fi amplifier system.

Last Answer : Characteristics of HI-FI amplifier: 1. Signal to noise ratio should be better than 50dB. 2. Frequency response should be flat within +-1dB. 3. Nonlinear distortion should not be more ... provided. 6. Environmental conditions should be such as to eliminate the external noise in listening room. 

Description : advantages and disadvantages of direct coupled amplifier over RC coupled amplifier. 

Last Answer : Advantages:  Due to absence of coupling capacitors, the gain does not reduce on the lower frequency side.  This amplifier can amplify dc signals. Reduced cost and complexity due to absence of ...   The output waveform has a dc shift.  Poor frequency response at a higher frequency.

Description :  transformer coupled amplifier

Last Answer :  transformer coupled amplifier

Description : State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Last Answer : The need of multistage amplifier The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in ... to use a MULTISTAGE AMPLIFIER .  Frequency response of R-C coupled amplifier.

Description : Define gain and bandwidth of an amplifier.

Last Answer : Bandwidth  The range of frequency over which the voltage gain is equal to or greater than 70.7% of its maximum value Gain: The ratio of output parameter (voltage/ current /power) to the input parameter (voltage/ current /power) of an amplifier is known as gain. It is denoted by a letter A

Description : Draw diagram of class A push-pull amplifier and explain its operation. 

Last Answer : Class A Push-pull Amplifier: The circuit diagram of class A push-pull amplifier is as shown in the fig.(a). Operation: The resistors R1 and R2 along with Vcc provide the dc biasing so as ... Vcc is applied to the collectors of transistors Q1 and Q2 through the centretapped output transformer. 

Description : Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Last Answer : Parameter RC coupled Transformer coupled Direct coupled  Coupling element Resistor and capacitor Transformer No element Impedance matching Poor Excellent good Frequency ... Low frequency amplifier,opamp Size and cost small Large and bulky least

Description : List the advantages of RC coupled amplifier.

Last Answer : Advantages: 1. The frequency response is excellent 2. The circuit is very compact and extremely light 3. Cost is low because it employ resistors and capacitors which are cheap 

Description : State the need of cascade amplifier.

Last Answer : Most systems a single transistor amplifier does not provide sufficient gain or bandwidth or will not have the correct input or output impedance matching. Hence cascade amplifier is use which consist more than one stages of amplification.

Description : Give the different types of amplifier coupling.

Last Answer : 1. Resistance – capacitance (RC) coupling.  2. Inductance (LC) coupling.  3. Transformer coupling (TC)  4. Direct coupling (D.C.)

Description : A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

Last Answer : A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

Description : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Last Answer : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Description : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

Last Answer : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

Description : Which one of the following is another name for common-collector amplifier?  A) Source follower B) Collector follower C) Base follower D) Emitter follower

Last Answer : Which one of the following is another name for common-collector amplifier?  A) Source follower B) Collector follower C) Base follower D) Emitter follower

Description : The voltage gains of the amplifier with and without feedback are 20 and 100 respectively. The percentage of negative feedback would be

Last Answer : The voltage gains of the amplifier with and without feedback are 20 and 100 respectively. The percentage of negative feedback would be 4%

Description : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

Last Answer : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be 2 watts

Description : A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by

Last Answer : A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by 2

Description : An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is  (1) 141 (2) 92.3 (3) 9.23 (4) 1.41

Last Answer : An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is 9.23

Description : The voltage gain of a common -source JFET amplifier depends up on its  (1) Input impedance (2) Amplification factor (3) Dynamic drain resistance (4) Drain load resistance

Last Answer : B

Description : The gain of an ideal amplifier must be

Last Answer : The gain of an ideal amplifier must be infinity

Description : The effect of a finite gain of an operational amplifier used in an integrator is that (A) it would not integrate (B) the slope of the output will vary with time (C) the final value of the output voltage will reduce (D) there will be instability in the circuit

Last Answer : The effect of a finite gain of an operational amplifier used in an integrator is that there will be instability in the circuit

Last Answer : The voltage regulation in magnetic amplifier type voltage regulator is effected by varying the reactance.

Description : What is a BJT amplifier?

Last Answer : Bilpolar Juntion transistor , this fuction is control the current

Last Answer : ADC-Amplifier interface: In most data acquisition system analog to digital converter (ADC) is interfaced with the amplifier. There are different interface architectural schemes. Operational ... . The interaction between analog to digital converter and amplifier affects the system performance.

Last Answer : Active region of BJT act as amplifier.

Description : Explain MCB and ELCB with connection diagram supplying single phase load. 

Last Answer : OR OR Explanation: * MCB provides short circuit protection. * MCB provides overload protection * ELCB provides earth fault protection. * MCB is in series with ... occurs, the ELCB cuts off the power within the time of 0.1 sec. automatically to protect the personnel. 

Description : Why is a capacitor used in a single phase motor and not in three phase motor ?

Last Answer : In 1-phase induction motor capacitor work is generate the auxiliary winding current than excite the main winding to rotor starts rotate. After rotor start rotating about 75% of their speed than auxiliary ... emf to start the motor.so,in 3-phase induction motor is self start induction motor.

Description : working principle of single phase motor

Last Answer : The Stator of single phase induction motor houses two windings  1. Main (Running) winding 2. Auxiliary (Starting ) winding Rotor of single phase induction motor is ... with starting winding or a capacitor may be permanently connected in series with Auxiliary (Starting ) winding.

Description : Explain the working of a single phase capacitor start induction motor. 

Last Answer : Single phase capacitor start induction motor https://youtu.be/31lvvzU5Puc

Description : What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

Last Answer : What is the slip (as a percentage) when a 6 pole single phase induction motor operating on 220 V and 60 Hz is rotating at speed of 1140 rpm? A) 60% B) 5% C) 10% D) None of these

Description : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

Last Answer : What is the power factor when a single phase watt meter operating on 200 V and 5 A for 5 hours makes 2016 revolutions and the meter constant in revolution is 420? A) 0.04 B) 1.04 C) 0.96 D) None of these

Description : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is (A) 28.2 mm (B) 26.4 mm (C) 24.4 mm (D) 22.0 mm

Last Answer : A single core cable is designed to work for a single phase system with a peak voltage of 220 kV. The maximum permissible stress in the dielectric is not to exceed 20 kV/mm. For economical size, the overall core diameter of the cable is 22.0 mm

Description : write short notes on single phase system.

Last Answer : A "phase" in an electrical system is often referred to as the waveform (may be voltage or the current) of the power supply. The waveform in an AC system is typically ... domestic household or commercial supplies and street lighting. Industrial supplies requires three phase electrical supply .

Description : SINGLE PHASE INDUCTION MOTORS MCQ

Last Answer : 101. After the starting winding of a single phase induction motor is disconnected from supply, it continues to run only on (a) running winding (b) rotor winding (c) field winding (d) compensating winding Ans: a ... motor is usually reduced by using (a) gearing (b) belts (c) brakes (d) chains Ans: a

Description : State the meaning of Single line diagram.

Last Answer : Meaning of Single line diagram: The single line diagram of a power system is the network which shows the main connections and arrangement of the system components along with their data ( ... breakers, transformers, capacitors, bus bars, and conductors are shown by standardized schematic symbols. 

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

Description : Single phase transformer

Last Answer : Single phase Transformer Transformer

Description : Single point Cutting tool signature

Last Answer : The shape of a tool is specified in a special sequence and this special sequence is called tool signature. The tool signature is given below (i) Back rake angle (ii) Side rake angle (iii) ... rake, end relief, side relief, end cutting edge, side cutting edge angle and 0.8 mm nose radius.

Description : State suitable single phase motor for following applications: (i) Table fan (ii) Mixers and Grinders

Last Answer : Application Suitable Single Phase Motor Table Fan 1) Capacitor split phase motor 2) Capacitor start capacitor run motor Mixers and Grinders 1) Universal motor 2) A.C. Series motor

Description : Illustrate with neat wiring diagram a single lamp control by two point method.

Last Answer : Single lamp control by two point method:  This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the ... the person will change the position of switch S2, so that the lamp will be switched OFF'.