Description : The term modem is a composite word that refers to the two functional entities that make up the device: asignal _______ and a signal _______. A) modulator; demodulator B) demodulator; modulator C) modern;demo D) none of the above
Last Answer : modulator; demodulator
Description : Which circuit detects frequency modulated signal? A. Modulator B. Discriminator C. Demodulator D. Modem
Last Answer : B. Discriminator
Description : Ina synchronous modem, the receive equilizer is known as a. adaptive equilizer b. impariment equilizer c. statistical equilizer d. compromise equilizer
Last Answer : adaptive equilizer
Description : The name “modem” is derived from (1) modern demarkator (2) modulator demand (3) modern demodulator (4) modulator demodulator
Last Answer : modulator demodulator
Description : Which of the following statement is correct? a. terminal section of a synchronous modem contains the scrambler b. receiver section of a synchronous modem contains the scrambler c. transmission section of ... d. control section of a synchronous modem contains the scrambler e. none of the above
Last Answer : transmission section of a synchronous modem contains the scrambler
Description : Computers cannot communicate with each other directly over telephone lines because they usedigitalpulses whereas telephone lines useanalog sound frequencies. What is the name of the device which permits digital to analog ... A. Interface B. Modem C. Attenuation D. Teleprocessor E. None of the above
Last Answer : Modem
Description : The primary purpose of the data modem is to A. interface analog terminal equipment to analog communications channel B. interface digital terminal equipment to analog communications ... to digital communications channel D. interface digital terminal equipment to digital communications channel
Last Answer : B. interface digital terminal equipment to analog communications channel
Description : The piece of hardware that converts your computers digital signal to an analog signal that can travel over telephone lines is called a: a) Red Wire b) Blue Cord c) Tower d) Modem e) None of These
Last Answer : d) Modem
Description : Which multiplexing technique transmits analog signals? A) FDM B) TDM C) WDM D) (a) and (c)
Last Answer : (a) and (c)
Description : The conversion of digital signal into analog for purposes of transmitting into the telephone line is done through ______. A. ISDN B. Radio C. RS232C D. Modem
Last Answer : D. Modem
Description : Which of the following statement is correct ? (A) Modem is a software (B) Modem helps in stabilizing the voltage (C) Modem is the operating system (D) Modem converts the analog signal into digital signal and vice-versa
Last Answer : (D) Modem converts the analog signal into digital signal and vice-versa
Description : In computing, how is a modulator-demodulator more commonly known?
Description : The basic modulator and demodulator circuits in PSK are:
Last Answer : Balanced modulators
Description : The slope of the analog signal is greater than the delta modulator can maintain
Last Answer : Slope overload
Description : ________conversion is therepresentation ofanalog information by an analog signal. A) Digital-to-analog B) Analog-to-analog C) Analog-to-digital D) Digital-to-digita
Last Answer : Analog-to-analog
Description : _______ conversionis the process of changing one of the characteristics ofan analog signal basedon the informationin the digitaldata. A) Digital-to-analog B) Analog-to-analog C) Analog-to-digital D) Digital-to-digital
Last Answer : Digital-to-analog
Description : A(n)_________ signal is a composite analogsignal with an infinite bandwidth. A) digital B) analog C) either (a)or (b) D) neither (a) nor (b
Last Answer : digital
Description : Bits can be sent over guided and unguided media as analog signal by ___________ a. digital modulation b. amplitude modulation c. frequency modulation d. phase modulation
Last Answer : a. digital modulation
Description : The signal which has infinitely many levels of intensity over a period of time is called ……… A. digital signal B. analog signal C. both a and b D. sound signal
Last Answer : A. digital signal
Description : Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometre) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable? a. 8000 b. 10000 c. 16000 d. 20000
Last Answer : d. 20000
Description : Modem is referred to as ______. A. Universal asynchronous Rx/Tx B. Data communication equipment C. Universal synchronous Rx/Tx D. Data terminal equipment
Last Answer : B. Data communication equipment
Description : Which multiplexing technique transmits digital signals? A) FDM B) TDM C) WDM D) None of the above
Last Answer : TDM
Description : Which of the following statement is incorrect? a. Multiplexers are designed to accept data from several I/O devices and transmit a unified stream of data on one communication line b. HDLC is a standard ... indicates that it is ready to accept data d. RTS/CTS is the way the terminal indicates ringing
Last Answer : RTS/CTS is the way the DTE indicates that it is ready to transmit data and the way the DCW indicates that it is ready to accept data
Description : The pieceof hardware that converts your computer'sdigital signal to ananalog signal that cantravel over telephone lines is called (A) red wire (B) blue cord (C) tower (D) modem (E) None of these
Last Answer : modem
Description : What digital carrier transmits a digital signal at 274.176 Mbps? A. T1 B. T3 C. T2 D. T4
Last Answer : D. T4
Description : A modem- 1) Translates along Signals from a computer into digital Signals that can travel along conventional telephone lines 2) Translates digital Signals from a computer into analog Signals that can ... conventional telephone lines 3) Demodulates digital Signals from a computer. 4) None of these
Last Answer : 4) None of these
Description : The device that converts digital signals to analog signals at the start of long distance transmissions is (1) peripheral (2) modem (3) telephone (4) antenna
Description : What is a Digital-to-Analog Converter (DAC) in Arduino?
Last Answer : A Digital-to-Analog Converter (DAC) in Arduino is a component that converts digital signals into analog signals, such as to control the output voltage to a motor or a speaker.
Description : What is an Analog-to-Digital Converter (ADC) in Arduino?
Last Answer : An Analog-to-Digital Converter (ADC) in Arduino is a component that converts analog signals, such as temperature or light, into digital signals that can be processed by the microcontroller.
Description : It is the ratio of the largest possible magnitude to the smallest possible magnitude that can be decoded by the digital-to-analog converter in the receiver.
Last Answer : Dynamic range
Description : A weighted resistor digital to analog converter using N bits requires a total of (A) N precision resistors. (B) 2N precision resistors. (C) N + 1 precision resistors. (D) N – 1 precision resistors.
Last Answer : (A) N precision resistors.
Description : The conversation speed of an analog to digital converter is maximum with the following technique. (A) Dual slope AD converter. (B) Serial comparator AD converter. (C) Successive approximation AD converter. (D) Parallel comparator AD converter.
Last Answer : (D) Parallel comparator AD converter.
Description : The number of comparators required in a 3-bit comparator type analog to digital converter is A) 2 B) 3 C) 7 D) 8
Last Answer : Number of comparators =2^n -1= 2^3 -1=7
Description : In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB is 2K, what will be the resistance corresponding to the LSB? (a) 250 Ω (d) 512 KΩ (c) 256 KΩ (d) 25.5 Ω
Last Answer : In a weighted-resistor digital-to-analog converter with 8-bit input, if the resistance corresponding to the MSB is 2K, what will be the resistance corresponding to the LSB? (a) 250 Ω (d) 512 KΩ (c) 256 KΩ (d) 25.5 Ω
Description : A digital voltmeter uses an A/D converter which needs a start pulse, uses an analog comparator and has a relatively fixed conversion time independent of the applied voltage. The A/D ... Successive Approximation Converter .b) Digital Ramp Converter c) Digital Slope Converter d) All the above
Last Answer : A digital voltmeter uses an A/D converter which needs a start pulse, uses an analog comparator and has a relatively fixed conversion time independent of the applied voltage. The A/D converter is : - Successive Approximation Converter
Description : A 4-bit R/2R digital-to-analog (DAC) converter has a reference of 5 volts. What is the analog output for the input code 1010: (1) 0.3125 V (2) 3.125 V (3) 0.78125 V (4) –3.125 V
Last Answer : 3.125V
Description : What is Analog to Digital Converter (ADC) ?
Last Answer : Analog to Digital Converter (ADC) Analog quantity may be voltage, temperature, sound, speed, audio etc. it is information or signal. ... digital form), digital speedometer (converts analog speed into digital form) etc.
Description : Digital to Analog Converter (DAC)
Last Answer : Digital to Analog Converter (DAC) Digital means binary (1 0) and 1 and 0 may be true and false or on and off or high and low. Analog means continuous signal or information ... wave. Phase Shift Keying (PSK) is transmit digital data by changing the phase of carrier wave.
Description : The most common technique to change an analog signal to digitaldata is called __________. A) PAL B) PCM C) sampling D) none of the abov
Last Answer : PCM
Description : Compared to analog signals, digital signals A. allow faster transmission B. are moreaccurate C. both (a)and (b) D. All of theabove E. None of the above
Last Answer : both (a)and (b)
Description : The line control unit (LCU) operates on the data digital form. A. Data communications equipment (DCE) B. UART C. Modem D. Data terminal equipment (DTE)
Last Answer : D. Data terminal equipment (DTE)
Description : In synchronous TDM, forn signal sources of the same data rate, eachframe contains _______ slots. A) n B) n + 1 C) n- 1 D) 0to n
Last Answer : n
Description : What do you call a circuit that controls the magnetron output? A. Inverter B. Impeller C. Modulator D. Converter
Last Answer : C. Modulator
Description : A hybrid computer a. Resembles digital computer b. Resembles analog computer c. Resembles both a digital and analog computer d. None of the above
Last Answer : Resembles both a digital and analog computer
Description : In analog computer a. Input is first converted to digital form b. Input is never converted to digital form c. Output is displayed in digital form d. All of above
Last Answer : All of above
Description : A digital computer did not score over an analog computer in terms of a. Speed b. Accuracy c. Cost d. Memory
Last Answer : Accuracy
Description : The computer that process both analog and digital is called a. Analog computer b. Digital computer c. Hybrid computer d. Mainframe computer
Last Answer : Hybrid computer
Description : An example of digital, rather than analog, communication is a. DDD b. DDS c. WATS d. DDT
Last Answer : DDS
Description : The process of converting analog signals into digital signals so they can be processed by a receiving computer is referred to as: a. modulation b. demodulation c. synchronizing d. digitising
Last Answer : digitising