characteristics of Hi-Fi amplifier system.

characteristics of Hi-Fi amplifier system.
by
retagged

1 Answer

Answer :

Characteristics of HI-FI amplifier:

1. Signal to noise ratio should be better than 50dB.

2. Frequency response should be flat within +-1dB.

3. Nonlinear distortion should not be more than 1%.

4. The system should possess dynamic range of at least 8dB.

5. Stereophonic effect should be provided.

6. Environmental conditions should be such as to eliminate the external noise in listening room. 
by

Related questions

working of class B push pull amplifier.

Description : working of class B push pull amplifier.

Last Answer : Circuit Diagram:- Operation:  In class B amplifier transistor conduct only for half cycle of input signal.One conduct in positive half cycle and other conducts in negative half ... Then output transformer joins these two halves and produces a full sine wave in the load resistor. 

Compare amplifier and oscillator.

Description : Compare amplifier and oscillator.

Last Answer : Figure shows a block diagram of an amplifier and an oscillator.   An amplifier is a device, which produces an output signal with similar waveform as that of the input. ... is supplied. An oscillator does not require any external signal to start or maintain energy conversion process.

role of tuned LC circuit in tuned amplifier.

Description : role of tuned LC circuit in tuned amplifier.

Last Answer : In order to pick up and amplify the desired radio frequency signal, the resistive load in the audio amplifier is replaced by a tuned circuit (also called a parallel resonant circuit)as shown ... desired radio frequency signal. (ii)Amplification of the selected signal to a suitable voltage level.

applications of RC coupled amplifier

Description :  applications of RC coupled amplifier

Last Answer : Applications of RC coupled amplifier: (i) Widely used as Voltage amplifiers. (ii) They are used in Public Address System. (iii) In Tape recorders. (iv) In stereo amplifiers (v) In T.V. V.C.R. and C.D. Players.

two stage amplifier and need of multistage amplifier.

Description :  two stage amplifier and need of multistage amplifier.

Last Answer : Circuit diagram of two stage amplifier : Need of multistage amplifier: The output from a single stage amplifier is usually insufficient to drive an output device. So that ... to second amplifier.  To increase the overall gain of the amplifier multistage amplifier is needed.

advantages and disadvantages of direct coupled amplifier over RC coupled amplifier.

Description : advantages and disadvantages of direct coupled amplifier over RC coupled amplifier. 

Last Answer : Advantages:  Due to absence of coupling capacitors, the gain does not reduce on the lower frequency side.  This amplifier can amplify dc signals. Reduced cost and complexity due to absence of ...   The output waveform has a dc shift.  Poor frequency response at a higher frequency.

transformer coupled amplifier

Description :  transformer coupled amplifier

Last Answer :  transformer coupled amplifier

Single stage CE amplifier

Description : Single stage CE amplifier

Last Answer : Requirement(Necessity) of Multistage amplifier: -In many applications we required a high gain. But sometimes gain produced by an amplifier is not sufficient so to increase the gain, we ... necessity of multistage amplifier is for providing high gain. It is also required for high bandwidth.

State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Description : State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Last Answer : The need of multistage amplifier The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in ... to use a MULTISTAGE AMPLIFIER .  Frequency response of R-C coupled amplifier.

Define gain and bandwidth of an amplifier.

Description : Define gain and bandwidth of an amplifier.

Last Answer : Bandwidth  The range of frequency over which the voltage gain is equal to or greater than 70.7% of its maximum value Gain: The ratio of output parameter (voltage/ current /power) to the input parameter (voltage/ current /power) of an amplifier is known as gain. It is denoted by a letter A

Draw diagram of class A push-pull amplifier and explain its operation.

Description : Draw diagram of class A push-pull amplifier and explain its operation. 

Last Answer : Class A Push-pull Amplifier: The circuit diagram of class A push-pull amplifier is as shown in the fig.(a). Operation: The resistors R1 and R2 along with Vcc provide the dc biasing so as ... Vcc is applied to the collectors of transistors Q1 and Q2 through the centretapped output transformer. 

State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Description : State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Last Answer : Need:- The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in order to obtain greater voltage and power gain, cascade amplifiers are used.

Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Description : Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Last Answer : Parameter RC coupled Transformer coupled Direct coupled  Coupling element Resistor and capacitor Transformer No element Impedance matching Poor Excellent good Frequency ... Low frequency amplifier,opamp Size and cost small Large and bulky least

List the advantages of RC coupled amplifier.

Description : List the advantages of RC coupled amplifier.

Last Answer : Advantages: 1. The frequency response is excellent 2. The circuit is very compact and extremely light 3. Cost is low because it employ resistors and capacitors which are cheap 

State the need of cascade amplifier.

Description : State the need of cascade amplifier.

Last Answer : Most systems a single transistor amplifier does not provide sufficient gain or bandwidth or will not have the correct input or output impedance matching. Hence cascade amplifier is use which consist more than one stages of amplification.

Give the different types of amplifier coupling.

Description : Give the different types of amplifier coupling.

Last Answer : 1. Resistance – capacitance (RC) coupling.  2. Inductance (LC) coupling.  3. Transformer coupling (TC)  4. Direct coupling (D.C.)

A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common

Description : A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

Last Answer : A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is

Description : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Last Answer : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

What is the efficiency of Class-B amplifier?

Description : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

Last Answer : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

Which one of the following is another name for common-collector amplifier?

Description : Which one of the following is another name for common-collector amplifier?  A) Source follower B) Collector follower C) Base follower D) Emitter follower

Last Answer : Which one of the following is another name for common-collector amplifier?  A) Source follower B) Collector follower C) Base follower D) Emitter follower

The voltage gains of the amplifier with and without feedback are 20 and 100 respectively. The percentage of

Description : The voltage gains of the amplifier with and without feedback are 20 and 100 respectively. The percentage of negative feedback would be

Last Answer : The voltage gains of the amplifier with and without feedback are 20 and 100 respectively. The percentage of negative feedback would be 4%

An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

Description : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

Last Answer : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be 2 watts

A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by

Description : A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by

Last Answer : A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by 2

An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of

Description : An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is  (1) 141 (2) 92.3 (3) 9.23 (4) 1.41

Last Answer : An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is 9.23

The voltage gain of a common -source JFET amplifier depends up on its

Description : The voltage gain of a common -source JFET amplifier depends up on its  (1) Input impedance (2) Amplification factor (3) Dynamic drain resistance (4) Drain load resistance

Last Answer : B

The gain of an ideal amplifier must be

Description : The gain of an ideal amplifier must be

Last Answer : The gain of an ideal amplifier must be infinity

The effect of a finite gain of an operational amplifier used in an integrator is that

Description : The effect of a finite gain of an operational amplifier used in an integrator is that (A) it would not integrate (B) the slope of the output will vary with time (C) the final value of the output voltage will reduce (D) there will be instability in the circuit

Last Answer : The effect of a finite gain of an operational amplifier used in an integrator is that there will be instability in the circuit

The voltage regulation in magnetic amplifier type voltage regulator is effected by?

Last Answer : The voltage regulation in magnetic amplifier type voltage regulator is effected by varying the reactance.

What is a BJT amplifier?

Description : What is a BJT amplifier?

Last Answer : Bilpolar Juntion transistor , this fuction is control the current

Write short note on ADC-Amplifier Interface.

Last Answer : ADC-Amplifier interface: In most data acquisition system analog to digital converter (ADC) is interfaced with the amplifier. There are different interface architectural schemes. Operational ... . The interaction between analog to digital converter and amplifier affects the system performance.

in which region BJT act as amplifier?

Last Answer : Active region of BJT act as amplifier.

Draw block diagram of Hi Fi amplifier.

Description : Draw block diagram of Hi Fi amplifier. 

Last Answer : block diagram of HiFi amplifier explain and draw the block diagram of amplifier

The desirable static characteristics of a measuring system are?

Last Answer : The desirable static characteristics of a measuring system are accuracy, sensitivity and reproducibility.

DTH System

Description : DTH System

Last Answer : Outdoor unit: It consists of a receiving antenna, low noise amplifier & converter the receiving antenna is parabolic reflector with a horn as the active element. The horn can be ... fed to the normal domestic TV receiver, which after due processing reproduces picture & sound. 

Describe the function of MUSE system for HDTV.

Description : Describe the function of MUSE system for HDTV.

Last Answer : Bandwidth can be reduced by MUSE (Multiple Sub -Nyquist Sampling Encoding) system MUSE stands for Multiple Sub-Nyquist sampling encoding and is an HDTV bandwidth compression schemedeveloped by ... digital Audio system is called DANCE (Digital Audio Near-Instantaneous Compression and expansion). 

requirements of a distribution system

Description : requirements of a distribution system

Last Answer : Following requirements of a distribution system.  1. Layout should be simple in design. 2. It should have less initial cost 3. The distribution system should have minimum distribution ... stability of existing distribution system. 15. Time required for completion of work should be less. 

Why radial distribution system used for short distance ?

Description : Why radial distribution system used for short distance ? 

Last Answer : Because of following disadvantages radial distribution system is not used for long distance:  Since there is only one feeder to DTC feed at one point so, 1) There is no reliability ... more time for fault finding & repairing Hence radial distribution system is used for short distance.

vertical deflection system and explain its operation.

Description : vertical deflection system and explain its operation.

Last Answer : The main function of the vertical deflection system , is to provide an amplified signal of proper level to derive the vertical deflection plates without any distortion. For amplification of the ... suppression, reduced nonlinear effects because none of the plates are at ground potential.

Working of Simple Vapor absorption system

Description : Working of Simple Vapor absorption system

Last Answer : Working of Simple Vapor absorption system:  A Simple Vapor absorption system consists of evaporator, absorber, generator, condenser, expansion valve, pump & reducing valve. In this system ammonia ... where there is scarcity of Electricity and it is very useful at partial and full load. 

Draw block diagram of CNC system and state function of each block.

Description : Draw block diagram of CNC system and state function of each block.

Last Answer : (i) Input Devices: These are the devices which are used to input the part program in the CNC machine. There are three commonly used input devices and these are punch tape reader, magnetic ... Unit: A monitor is used to display the programs, commands and other useful data of CNC machine. 

Write four advantages of FMS (Flexible Manufacturing System).

Description : Write four advantages of FMS (Flexible Manufacturing System).

Last Answer : 1. Large variety of same products 2. Profitable investment. 3. Requires limited inventory. 4. Low labor cost. 5. Flexible system. 6. Speedy production. 7. Improve product quality. 

List and explain the components of a hydraulic system.

Description : List and explain the components of a hydraulic system.

Last Answer : Components Hydraulic: Hydraulic pump- Supply fluid to the components in the system. Pressure in the system develops in reaction to the load. Hence, a pump rated for 5,000 ... mechanical components and need to be removed along with other contaminants.  Seals, fittings and connections.

Explain how MEMS accelerometer is used as airbag sensor for car system.

Description : Explain how MEMS accelerometer is used as airbag sensor for car system.

Last Answer : MEMS Accelerometer is used as airbag sensor: Mechanical ignition airbags fit inside the steering wheel pad. When a collision occurs, the inertial sensor moves, setting off a ... the airbag with wiring. This is especially effective when fitting both driver- and passenger-side airbags.

What are advantages and disadvantages of Mechatronics system?

Description : What are advantages and disadvantages of Mechatronics system? 

Last Answer : Advantages of Mechatronics system:  High level of integration.  Increased functionality and better design.  More use of electronics and software instead of mechanical function.  Assumes ... Its replacement is difficult, that it is difficult to change old system to new system. 

Explain in brief how anti-lock braking system works

Description : Explain in brief how anti-lock braking system works

Last Answer : An ABS is a system on motor vehicles which prevents the wheels from locking while braking stopping safely is one of the most important functions a motor vehicle can perform. Diagram: ... to decrease the pressure on the braking circuit, effectively reducing the braking force on that wheel.

Differentiate between pneumatic and hydraulic system.

Description : Differentiate between pneumatic and hydraulic system. 

Last Answer : Pneumatic System Hydraulic System 1 Pneumatic system uses gas for power transmission, after compression and it is used as medium for carrying out mechanical work. ... : In industrial applications, air conditioners Applications: In petrochemical industries, oil refineries.

Explain the Mechatronics system with the help of block diagram and labeled the various elements.

Description : Explain the Mechatronics system with the help of block diagram and labeled the various elements. 

Last Answer : The key elements of Mechatronics systems can be classified under following categories:  Information systems  Mechanical systems  Electrical systems  Computer systems  Sensor and actuators  ... is adjusted based on generated error and again signal is given to actuators and sensors.

Describe the procedure for working of paging system.

Description : Describe the procedure for working of paging system.

Last Answer : Pager is a Simplex Communication Device. Paging Systems are communication systems that send messages to a subscriber. Message can be numeric or alphanumeric. Paging Systems are used to notify a subscriber ... message is sent by sender to his pager and the message will be displayed in the LCD.

State the need of modulation in communication system.

Description : State the need of modulation in communication system.

Last Answer : Need of modulation:- 1. To reduce the height of antenna 2. To avoids mixing of signals 3. To increases the range of communication 4. To make multiplexing of maximum signal is possible 5. To improve the quality of reception

Why solar system is preferred now a days ? Justify your answer.

Description : Why solar system is preferred now a days ? Justify your answer. 

Last Answer : Since availability of fossil fuels like coal are limited in future so there is more importance of solar power in the energy deficient because of following advantages of solar power Fuel is ... .  10. solar system technology are ideally suited to distributed applications ( Decentralized system)