applications of RC coupled amplifier

1 Answer

Answer :

Applications of RC coupled amplifier:

(i) Widely used as Voltage amplifiers.

(ii) They are used in Public Address System.

(iii) In Tape recorders.

(iv) In stereo amplifiers

(v) In T.V. V.C.R. and C.D. Players.

Related questions

Description : Compare RC coupled, transformer coupled and direct coupled amplifier based on four points.

Last Answer : Parameter RC coupled Transformer coupled Direct coupled  Coupling element Resistor and capacitor Transformer No element Impedance matching Poor Excellent good Frequency ... Low frequency amplifier,opamp Size and cost small Large and bulky least

Description : List the advantages of RC coupled amplifier.

Last Answer : Advantages: 1. The frequency response is excellent 2. The circuit is very compact and extremely light 3. Cost is low because it employ resistors and capacitors which are cheap 

Description : advantages and disadvantages of direct coupled amplifier over RC coupled amplifier. 

Last Answer : Advantages:  Due to absence of coupling capacitors, the gain does not reduce on the lower frequency side.  This amplifier can amplify dc signals. Reduced cost and complexity due to absence of ...   The output waveform has a dc shift.  Poor frequency response at a higher frequency.

Description :  transformer coupled amplifier

Last Answer :  transformer coupled amplifier

Description : State the need of multistage amplifier. Draw frequency response of R-C coupled amplifier.

Last Answer : The need of multistage amplifier The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in ... to use a MULTISTAGE AMPLIFIER .  Frequency response of R-C coupled amplifier.

Description : State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Last Answer : Need:- The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in order to obtain greater voltage and power gain, cascade amplifiers are used.

Last Answer : An alternator coupled to a hydraulic turbine runs at slow speed, as compared to others.

Description : Explain DC coupled drive circuit with unipolar output.

Last Answer : DC coupled drive circuit with unipolar output: The figure shows the circuit and waveforms

Description : Compare RC and LC oscillator.

Last Answer :  RC and LC oscillator

Description : Series rc circuits

Last Answer : Series rc circuits

Description : Parallel rc circuit

Last Answer : Parallel rc circuit

Description : Source free RC circuit 2

Last Answer : Source free RC circuit 2

Description : Source free RC circuit 3

Last Answer : Source free RC circuit 3

Description : Source free RC circuit 4

Last Answer : Source free RC circuit 4

Description : Source free RC circuit 5

Last Answer : Source free RC circuit 5

Description : Source free RC circuit 6

Last Answer : Source free RC circuit 6

Description : Source free RC circuit 7

Last Answer : Source free RC circuit 7

Description : Source free RC circuit 8

Last Answer : Source free RC circuit 8

Description : Compare RC and LC filter.

Last Answer : RC filters  LC filters The RC filter is only useful for small load currents. The LC filters are useful for heavy load currents. More power dissipated in RC filter. Less power ... RC is fine for filtering low power signals. LC is fine for filtering high power signals.

Description : Draw and explain RC phase shift Oscillator.

Last Answer : Circuit diagram of RC phase shift oscillator: WORKING: * Circuit consists of a single stage amplifier in common emitter configuration & RC phase shifting network. * R1, R2, RE provides biasing & CE ... . * The phase shift around the loop is 3600 only at one precise frequency.  

Description : RC Heli recommendation for a newbie?

Last Answer : answer:Helis are hard to fly; I'd recommend trying RC foamies first or starting with a smaller, cheaper heli (you are going to crash it at least a few times-everyone does when they get ... things expensive but they can be really great when tuned just right. Are you an engineer by background?

Description : Can An Rc Circuit Be Used As Clock Source For 8085?

Last Answer : Answer :Yes, it can be used, if an accurate clock frequency is not required. Also, the component cost is low compared to LC or Crystal.

Description : Explain the operation of RC triggering circuit with neat diagram.

Last Answer : RC triggering circuit: The RC half-wave triggering circuit is as shown in the figure. During negative halfcycle of supply voltage vs, the capacitor C charges through diode D2 and load, ... be triggered at 0° & 180° because the supply voltage is zero and less than finger voltage. 

Description : Time constant for RC circuit formula τ = RC Where, τ = time constant

Last Answer : Time constant for RC circuit formula τ = RC Where, τ = time constant

Description : RC triggering is preferred over resistance triggering because (A) it provides triggering at a precise instant (B) it gives a longer duration gate pulse (C) it enables triggering at a larger value of firing angle (D) it protects the SCR against high dv/dt

Last Answer : a

Description : working of class B push pull amplifier.

Last Answer : Circuit Diagram:- Operation:  In class B amplifier transistor conduct only for half cycle of input signal.One conduct in positive half cycle and other conducts in negative half ... Then output transformer joins these two halves and produces a full sine wave in the load resistor. 

Description : Compare amplifier and oscillator.

Last Answer : Figure shows a block diagram of an amplifier and an oscillator.   An amplifier is a device, which produces an output signal with similar waveform as that of the input. ... is supplied. An oscillator does not require any external signal to start or maintain energy conversion process.

Description : role of tuned LC circuit in tuned amplifier.

Last Answer : In order to pick up and amplify the desired radio frequency signal, the resistive load in the audio amplifier is replaced by a tuned circuit (also called a parallel resonant circuit)as shown ... desired radio frequency signal. (ii)Amplification of the selected signal to a suitable voltage level.

Description : characteristics of Hi-Fi amplifier system.

Last Answer : Characteristics of HI-FI amplifier: 1. Signal to noise ratio should be better than 50dB. 2. Frequency response should be flat within +-1dB. 3. Nonlinear distortion should not be more ... provided. 6. Environmental conditions should be such as to eliminate the external noise in listening room. 

Description :  two stage amplifier and need of multistage amplifier.

Last Answer : Circuit diagram of two stage amplifier : Need of multistage amplifier: The output from a single stage amplifier is usually insufficient to drive an output device. So that ... to second amplifier.  To increase the overall gain of the amplifier multistage amplifier is needed.

Description : Single stage CE amplifier

Last Answer : Requirement(Necessity) of Multistage amplifier: -In many applications we required a high gain. But sometimes gain produced by an amplifier is not sufficient so to increase the gain, we ... necessity of multistage amplifier is for providing high gain. It is also required for high bandwidth.

Description : Define gain and bandwidth of an amplifier.

Last Answer : Bandwidth  The range of frequency over which the voltage gain is equal to or greater than 70.7% of its maximum value Gain: The ratio of output parameter (voltage/ current /power) to the input parameter (voltage/ current /power) of an amplifier is known as gain. It is denoted by a letter A

Description : Draw diagram of class A push-pull amplifier and explain its operation. 

Last Answer : Class A Push-pull Amplifier: The circuit diagram of class A push-pull amplifier is as shown in the fig.(a). Operation: The resistors R1 and R2 along with Vcc provide the dc biasing so as ... Vcc is applied to the collectors of transistors Q1 and Q2 through the centretapped output transformer. 

Description : State the need of cascade amplifier.

Last Answer : Most systems a single transistor amplifier does not provide sufficient gain or bandwidth or will not have the correct input or output impedance matching. Hence cascade amplifier is use which consist more than one stages of amplification.

Description : Give the different types of amplifier coupling.

Last Answer : 1. Resistance – capacitance (RC) coupling.  2. Inductance (LC) coupling.  3. Transformer coupling (TC)  4. Direct coupling (D.C.)

Description : A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

Last Answer : A differential amplifier has a differential gain of 28000 and CMRR is 60 dB. What will be the value of common mode gain? A) Ac = 0.125 B) Ac = 0.33 C) Ac = 3 D) Ac = 28 

Description : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Last Answer : The unity gain bandwidth of an inverting amplifier is 10 MHz What would be the bandwidth if the gain is increased to 10 V/V? A) 100 MHz B) 1 MHz C) 10 MHz D) 1 kHz 

Description : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

Last Answer : What is the efficiency of Class-B amplifier?  A) 68.50% B) 78.50% C) 88.50% D) 98.50%

Description : Which one of the following is another name for common-collector amplifier?  A) Source follower B) Collector follower C) Base follower D) Emitter follower

Last Answer : Which one of the following is another name for common-collector amplifier?  A) Source follower B) Collector follower C) Base follower D) Emitter follower

Description : The voltage gains of the amplifier with and without feedback are 20 and 100 respectively. The percentage of negative feedback would be

Last Answer : The voltage gains of the amplifier with and without feedback are 20 and 100 respectively. The percentage of negative feedback would be 4%

Description : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be

Last Answer : An amplifier has input power of 2 microwatts. The power gain of the amplifier is 60 dB. The output power will be 2 watts

Description : A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by

Last Answer : A differential amplifier has a differential gain of 20,000, CMRR : 80 dB. The common mode gain is given by 2

Description : An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is  (1) 141 (2) 92.3 (3) 9.23 (4) 1.41

Last Answer : An amplifier has a voltage gain of 120. To reduce distortion, 10% negative feedback is employed. The gain of the amplifier with feedback is 9.23

Description : The voltage gain of a common -source JFET amplifier depends up on its  (1) Input impedance (2) Amplification factor (3) Dynamic drain resistance (4) Drain load resistance

Last Answer : B

Description : The gain of an ideal amplifier must be

Last Answer : The gain of an ideal amplifier must be infinity

Description : The effect of a finite gain of an operational amplifier used in an integrator is that (A) it would not integrate (B) the slope of the output will vary with time (C) the final value of the output voltage will reduce (D) there will be instability in the circuit

Last Answer : The effect of a finite gain of an operational amplifier used in an integrator is that there will be instability in the circuit

Last Answer : The voltage regulation in magnetic amplifier type voltage regulator is effected by varying the reactance.

Description : What is a BJT amplifier?

Last Answer : Bilpolar Juntion transistor , this fuction is control the current

Last Answer : ADC-Amplifier interface: In most data acquisition system analog to digital converter (ADC) is interfaced with the amplifier. There are different interface architectural schemes. Operational ... . The interaction between analog to digital converter and amplifier affects the system performance.

Last Answer : Active region of BJT act as amplifier.