1 Answer

Answer :

10 ohm

Related questions

Description : Suggest the diode material suitable to rectify 0.5V AC signal.

Last Answer : The diode material suitable to rectify 0.5V AC signal is silicon

Description : When using an ohmmeter to test a semiconductor diode, you find a low resistance in both the forward and reverse bias directions. This indicates that the diode has a/an ____________. A. open B. short C. good resistive quality D. good capacitive quality

Last Answer : Answer: B

Description : Avalanche breakdown in a diode occurs when a. Potential barrier is reduced to zero. b. Forward current exceeds certain value. c. Reverse bias exceeds a certain value. d. None of these

Last Answer : c. Reverse bias exceeds a certain value.

Description : A neon flashlight cell with an emf of 1.5V gives a current of 15A when connected directly to an ammeter of resistance 0.04?. Internal resistance of the cell is a. 0.0004? b. 0.06? c. 0.10? d. 0.13?

Last Answer : b. 0.06?

Description : Junction breakdown occurs: a) With forward bias b) With reverse bias c) Under high temperature condition d) Because of excess heating of the diode

Last Answer : Ans: B

Description : While testing a semi-conductor diode with an ohmmeter, both the forward and reverse readings are almost in the infinity range. This would indicate that the unit is _____________. A. good B. open C. grounded D. shorted

Last Answer : Answer: B

Description :  A device used to avoid the relay destroying the op-amp is A. diode B. LED C. reverse bias diode D. forward biased diode

Last Answer : reverse bias diode

Description : Photo diode operates in the _______ condition (a) Forward bias (b) null (c) both a & d (d) reverse bias

Last Answer : (d) reverse bias

Description : Define i)P-N junction diode ii) Depletion layer iii)Forward bias iv)Reverse bias of P-N junction diode

Last Answer : i)P-N junction diode: It is a semiconductor device in which half of its region is P-type and other half is N-type.  ii) Depletion layer: The region where free electrons and free holes are absent ... and negative terminal is connected to p-side of p-n junction diode, it is said to be reverse bias.

Description : A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is also in series with the diode. The current is a. 10 mA b. 9.3 mA c. 0.7 mA d. 0

Last Answer : b. 9.3 mA

Description : How much time a diode takes to switch ON in forward bias condition.

Last Answer : t=0 sec.

Description : The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave calibration pulse is connected to channel 1 ofthe scope the waveform observed on the screen ... channels are the same, the amplitude (pp) and period of the unknown signal are respectively.

Last Answer : The time/div and voltage/div axes of an oscilloscope have been erased. When a 1 kHz, 5V p-p square wave calibration pulse is connected to channel 1 ofthe scope the waveform observed on the screen is ... are the same, the amplitude (pp) and period of the unknown signal are respectively. 7.5 V, 2ms

Description : The output voltage V0 ofthe Schmitt trigger shown in figure swings between +15V and -1 5V. Assume that the operational amplifier is ideal. The output will change from +1 5 V to -1 5V when the ... slope only C) Vin the positive and negative slopes D) 3 V in the positive and negative slopes

Last Answer : The output voltage V0 ofthe Schmitt trigger shown in figure swings between +15V and —1 5V. Assume that the operational amplifier is ideal. The output will change from +1 5 V to -1 5V when the instantaneous value of the input sine wave is 5 V in the positive slope only

Description : The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at a gate voltage of 3V. Pinch off would be occurs at a drain voltage of (A) 1.5V (B) 2.5V (C) 3.5V (D) 4.5V

Last Answer : The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at a gate voltage of 3V. Pinch off would be occurs at a drain voltage of 2.5V

Description : Determine the voltage drop across the resistance `R_(1)` in the circuit given in Fig. 4.55 with `epsilon=90 V, R_(1)=5 k Omega, R_(2)=5k Omega, R_(3)=

Last Answer : Determine the voltage drop across the resistance `R_(1)` in the circuit given in Fig. 4.55 with `epsilon=90 V, ... k Omega " and " R_(4)=10 k Omega`.

Description : A diode in which the change in reverse bias voltage varies the capacitance is called as A) Varactor diode B) Switching diode C) Tunnel diode D) Zener-diode  

Last Answer : A diode in which the change in reverse bias voltage varies the capacitance is called as Varactor diode

Description : Why does a forward biased diode offer low resistance?

Last Answer : The external voltage over comes the junction potential and provides an easy path for the flow of charges across the junction. Hence it offers low resistance.

Description : What is the typical back-to-forward resistance ratio of a good-quality diode?

Last Answer : 10-to-1 ratio.

Description : As a rule of thumb, what is an acceptable ratio of back-to forward resistance for a diode?

Last Answer : Greater than 10 to 1

Description : When the diode is forward biased, it is equivalent to a. An off switch b. An On switch c. A high resistance d. None of the above

Last Answer : b. An On switch

Description : Define dynamic resistance of diode. State, how it is calculated using forward characteristics of diode.

Last Answer : Definition: The resistance offered by the diode to the AC operating conditions is known as the Dynamic resistance' or Incremental resistance' or AC resistance' of a diode. It is ... Dynamic resistance is actually the reciprocal of the slope of the forward characteristics.

Description : A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the diode. The current through the diode is

Last Answer : A forward potential of 10V is applied to a Si diode. A resistance of 1 KΩ is in series with the diode. The current through the diode is 9.3 mA

Description : When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?

Last Answer : Feel Free to Answer

Description : A Hybrid Vehicle equipped with push button start will enter the power ON mode but will not enter the ready to drive mode .No diagnostic trouble code are stored this could cause by a) The high voltage safety ... removed b) A failed brake on/off switch c) An empty fuel tank d) A disconnect 12v battery

Last Answer : b) A failed brake on/off switch

Description : Which voltage is likely to be available from the battery of an electric vehicle also known as Mild hybrid? a) 12V b) 24V c) 300V d) 100V

Last Answer : c) 300V

Description : What is a typical ARC voltage setting when welding with the TIG (GTAW) process? a) 18-20V b) 24-26V c) 10-12V d) 70-90V

Last Answer : c) 10-12V

Description : Process of conversion low voltage to high voltage is called _______ (a) Rectification (b)forward bias (c) reverse bias (d) amplification

Last Answer : (d) amplification

Last Answer : A Zener diode is operated in the Reverse bias around the knee of breakdown region mode as a voltage stabilizer.

Description : Which diode exhibits negative resistance characteristic? (A) LED (B) Zener (C) Tunnel diode (D) PN diode

Last Answer : Which diode exhibits negative resistance characteristic? (A) LED (B) Zener (C) Tunnel diode (D) PN diode

Description : 9 leds each of 1 volt drop is series with 9  volt battery , do we need a resistor?(SMD leds) I have seen some smd leds without resistor !

Last Answer : We connect resistor to limit the current. So, it depends upon the current rating of the LED, which is provided by manufacturer.

Description : On increasing the reverse bias to a large value in a p-n junction diode current (a) Increases slowly (b) Remains fixed (c) Suddenly increases (d) Decreases slowly

Last Answer : (c) Suddenly increases

Description : The reverse current through semiconductor diode is due to (a) Minority carrier (b) majority carrier (c) electrons (d) holes

Last Answer : (a) Minority carrier

Description : When a reverse bias is applied to a diode, it will a. Raise the potential barrier b. Lower the potential barrier c. Increases the majority-carrier a current greatly d. None of these

Last Answer : a. Raise the potential barrier

Description : How can we protect circuit from reverse voltage polarity?

Last Answer : We can protect circuit from reverse voltage by connecting diode in series but connecting diode in series is less efficient. So we can also protect circuit from reverse voltages by connecting p channel ... gate and source of mosfet and input voltage is applied between drain and Gate of mosfet.

Description : Forward current through a semi-conductor diode circuit is due to ________ (a) Minority carriers (b) majority carriers (c) holes (d) electrons

Last Answer : (b) majority carriers

Description : The distance between a generator and its load is 100 feet. What would be the approximate total voltage drop across a two wire supply cable if the current were 5.5 amperes and the resistance of the wire were 2.525 ohms per 1,000 feet? A. 0.5 volts B. 1.38 volts C. 1.90 volts D. 2.77 volts

Last Answer : Answer: D

Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current

Last Answer : Answer: D

Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

Description : In a DC series circuit, all the conductors have the same ____________. A. power expended in them B. voltage drop across them C. resistance to current flow D. current passing through them

Last Answer : Answer: D

Description : If current of 20 mA is passing through op-amp and voltage drop across series resistor is 10 V then value of resistance is A. 500Ω B. 400Ω C. 300Ω D. 200Ω

Last Answer : 500Ω

Description : In order that current should flow without causing excessive heating or voltage drop, the relay contacts should (a) have low contact resistance (b) be clean and smooth (c) be of sufficient size and proper shape (d) have all above properties

Last Answer : (d) have all above properties

Description : Refering to the illustrated schematic diagram, which of the following statements is true when the motor is running in the forward direction? EL-0011 A. Normally-open contacts '4-5' are closed. B. Current ... switch. C. Normally-closed contacts 'R' are open. D. The blowout coils must be closed.

Last Answer : Answer: B

Description : The purpose of a heat sink, as frequently used with transistors, is to ____________. A. prevent excessive temperature rise B. compensate for excessive doping C. increase the reverse current D. decrease the forward current

Last Answer : Answer: A

Description : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively   (a) 10A, 7.07A (b) 5A, 10A (c) 5A, 7.07A (d) 7.07A, 5A

Last Answer : A single-phase full-bridge diode rectifier delivers a load current of 10A, which is ripple free. Average and rms values of diode currents are respectively 5A, 7.07A

Last Answer : In Reverse bias of diode when the cathode is connected to positive and anode is connected to negative very small current flows this very small current is known as leakage current of diode.

Description : I don't know how to deal with Czech at all.

Last Answer : lol lmao xd: b

Description : Two cells of emfs approximately 5V and 10V are to be accurately compared using a poteniometer of length 400 cm.

Last Answer : Two cells of emfs approximately 5V and 10V are to be accurately compared using a ... usually used for comparing resistances and not voltages

Description : A charge of 2C passes from one point to the other in a circuit. If the potential difference between the two points is 5V, the amount of work done is : (1) 10 J (2) 0.4 J (3) 2.5 J (4) 5 J

Last Answer : (1) 10 J

Description : To determine the polarity of the voltage drop across a resistor, it is necessary to know?

Last Answer : To determine the polarity of the voltage drop across a resistor, it is necessary to know direction of current through the resistor.