If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

1 Answer

Answer :

If the 12 Ohm resistor draws a current of 1 A as shown in the figure, the value of resistance R is

image

Related questions

Description : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is A) 25 A B) 50 A C) 100 A D) 200A

Last Answer : As shown in the figure, 1 ohm resistance is connected across a source that has a load line v + i = 100. The current through the resistance is 50 A

Description : Each resistor shown in the figure has a resistance of `10 Omega` and the battery has the emf 6 V. What will be the current supplied by the battery ?

Last Answer : Each resistor shown in the figure has a resistance of `10 Omega` and the battery has the emf 6 V. What will be the ... 2 A` C. `1.8 A` D. `0.3 A`

Description : The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 ... .5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

Last Answer : The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be 48.0%

Description : Consider the star network shown in figure. The resistance between terminals A and B with C open is 6 ohms, between terminals B and C withAopen is 11 ohms and between terminals C andAwith B open is 9 ohms. Then RA, RB, RC respectively is 

Last Answer : Consider the star network shown in figure. The resistance between terminals A and B with C open is 6 ohms, between terminals B and C withAopen is 11 ohms and between terminals C andAwith B open is 9 ohms. Then RA, RB, RC respectively is  2, 4,7

Description : An ammeter with an internal resistance of 50 ohm(s) is used to measure a current thorugh a lod resistor Rl = 1 kohm(s). Determine the percentage error of the reading due to ammeter insertion.

Last Answer : 50/(50+1k)*100 = 4.76%

Description : Three unequal resistor in parallel are equivalent to a resistance `1` ohm If two of them are in the ratio `1:2` and if no resistance value is fraction

Last Answer : Three unequal resistor in parallel are equivalent to a resistance `1` ohm If two of them are in the ratio `1:2` and ... in ohm is A. 4 B. 6 C. 8 D. 12

Description : Resistance between points A and B in the circuit shown in figure is a. 4 ohm b. 6ohm c. 10 ohm d. 8 ohm

Last Answer : c. 10 ohm

Description : In the circuit shown here, what is the value of the unknown resistor R so that the total resistance of the circuit between points P and Q is also equa

Last Answer : In the circuit shown here, what is the value of the unknown resistor R so that the total resistance of the ... ` C. `sqrt(69)Omega` D. `10 Omega`

Description : If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be?

Last Answer : If the energy is supplied from a source, whose resistance is 1 ohm, to a load of 100 ohms the source will be a voltage source.

Description : In the circuit shown in figure, the resistance R has a value that depends on the current. Specifically R is 20 `Omega` when `i` is zero and the amount

Last Answer : In the circuit shown in figure, the resistance R has a value that depends on the current. Specifically R is 20 `Omega` ... A B. `10A` C. 20 A D. `5A`

Description : An uncharged capacity ER C=`100muF` with a resistor is connected with AC source as shown in the figure If R= is `50Omega` and switch S is closed at t=

Last Answer : An uncharged capacity ER C=`100muF` with a resistor is connected with AC source as shown in the figure If R ... `(v_(A)-V_9B)` is k volt. Calculate K

Description : A five ohm and a ten ohm resistor are connected in parallel, what single resistance is "equivalent" to this combination? 

Last Answer : ANSWER: 3 AND 1/3 OHM

Description : A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Last Answer : ANSWER: W -- 25 OHMS

Description : A circuit has a resistance of 200 ohms. The resistance of the circuit can be reduced to 120 ohms by adding which of the following to the circuit. w) 80 ohm resistor in series x) 150 ohm resistor in parallel y) 240 ohm resistor in series z) 300 ohm resistor in parallel

Last Answer : ANSWER: Z -- 300 OHM RESISTOR IN PARALLEL

Last Answer : A metal resistor has resistance of 10 ohm at 0°C and 11 ohms at 160°C, the temperature coefficient is 0.000625 /°C.

Description : Find the equivealent resistance of the circuit shown in Fig. 4.61 between the points P and Q. Each resistor has a resistance r.

Last Answer : Find the equivealent resistance of the circuit shown in Fig. 4.61 between the points P and Q. Each resistor has a resistance r.

Description : Find the equivalent resistance of the circuit shown in Fig.4.60 between the points A and B. Each resistor has a resistance r.

Last Answer : Find the equivalent resistance of the circuit shown in Fig.4.60 between the points A and B. Each resistor has a resistance r.

Description : A lamp is provided with 110 volts and draws a current of 0.8 amps. What is the resistance of the lamp? A. 12.2 ohms B. 88.0 ohms C. 122.2 ohms D. 137.5 ohms

Last Answer : Answer: D

Description : Find current through resistor using nodal analysis

Last Answer : Find current through resistor using nodal analysis

Description : In the illustrated circuit 'A', what power is consumed by a 3 ohm resistor with a 12 volt source? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Last Answer : Answer: B

Description : In the illustration what is the minimum wattage needed for a 3 ohm resistor with a 12 VDC power source in circuit 'A'? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Last Answer : Answer: B

Description : With a 12 V supply, a silicon diode, and a 370 - ohm resistor in series, what voltage will be dropped across the diode? a) 0.3V b) 0.7V c) 0.9V d) 1.4V

Last Answer : 0.7V

Description : A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and minimum values of the output waveform vout of the circuit are respectively

Last Answer : A voltage signal 10 Sinwt is applied to the circuit with ideal diodes, as shown in figure. The maximum and minimum values of the output waveform vout of the circuit are respectively +4V and-7V

Description : Six resistance each of value `r=5 Omega` are connected between points A, B and C as shown in figure. If `R_(1), R_(2)` and `R_(3)` are the net resista

Last Answer : Six resistance each of value `r=5 Omega` are connected between points A, B and C as shown in figure. If `R_(1), R_(2) ... 1:2:3` C. `5:4:3` D. `4:3:2`

Description : What is the power used in a circuit that has 10 amperes of current through a 10-ohm resistor?

Last Answer : 1 kilowatt.

Description : A current of 5 amps passes through a 10 ohm resistor. What power is dissipated by this resistor under these conditions?

Last Answer : ANSWER: 250 WATTS

Description : The potential difference across a 4 ohm resistor is 20 volts. What is the current in the resistor?

Last Answer : ANSWER: 5 AMPS

Description : A current of 6 amperes flows through a 2 ohm resistor for 30 seconds. How many coulombs of charge have passed through the resistor? 

Last Answer : ANSWER: 180 COULOMBS

Description : A series circuit consists of a two ohm RESISTOR and a one ohm INDUCTOR. The relationship between current and voltage is: w) current will lag by 30 degrees. x) current will lag by 26 degrees. y) current will lead by 26 degrees. z) current will lead by 30 degrees.

Last Answer : ANSWER: X -- CURRENT WILL LAG BY 26 DEGREES.

Description : A 10 ohm and a 20 ohm resistor are connected in parallel to a current source. What fraction of the current flows through the 20 ohm resistor? w) 1/2 x) 1/3 y) 2/3 z) 3/4

Last Answer : ANSWER: X -- 1/3

Description : A 20 ohm resistor and a 60 ohm resistor are connected in parallel to a voltage source. If the current in the 60 ohm resistor is one ampere, the current in the 20 ohm resistor will be: w) 1/3 ampere x) 2/3 ampere y) 1 ampere z) 3 amperes

Last Answer : ANSWER: Z -- 3 AMPERES

Description : A current of 5 amps passes through a 10 ohm resistor. How many joules of energy will be generated by this resistor in 2 seconds? 

Last Answer : ANSWER: 500 JOULES

Description : Which of the following statements is correct concerning the motor performance curves and data table shown in the illustration? EL-0006 A. The motor RPM at full load is 1737 RPM. B. The motor draws 12.62 kw ... If the motor was developing 10 HP its power factor would be 0.92. D. All of the above.

Last Answer : Answer: D

Description : N resistors of each of resistance R when connected in series offer an equivalent resistance of 50 ohm and when reconnected in parallel the effective resistance is 2 ohm the value of R is

Last Answer : 25 ohms

Description : The third color band on a resistor is used to indicate the ______________. A. tolerance of the resistor B. number of zeros following the first two significant figures in the resistance value C. first significant figure of the resistance D. second significant figure of the resistance

Last Answer : Answer: B

Description : The emf of a cell E is 15 V as shown in the figure with an internal resistance of `0.5Omega`. Then the value of the current drawn from the cell is

Last Answer : The emf of a cell E is 15 V as shown in the figure with an internal resistance of `0.5Omega`. Then the value of ... A. `3A` B. `2A` C. `5A` D. `1A`

Description : What is the resistance of a circuit that operates on 12 volts and draws 7 amps?

Last Answer : Need answer

Description : To determine the polarity of the voltage drop across a resistor, it is necessary to know?

Last Answer : To determine the polarity of the voltage drop across a resistor, it is necessary to know direction of current through the resistor.

Description : Can a supernode contain a resistor?

Last Answer : contain

Description : Four resistances are connected in a circuit in the given figure. The electric cirrent flowing through `4 ohm` and `6 ohm` resistance is respectively

Last Answer : Four resistances are connected in a circuit in the given figure. The electric cirrent flowing through `4 ohm` and `6 ... 1 A and 1 A D. 2 A and 2 A

Description : Assertion : In the circuit shown in figure, battery is ideal. If a resistance `R_(0)` is cannected in parallel with R, then power across R will increa

Last Answer : Assertion : In the circuit shown in figure, battery is ideal. If a resistance `R_(0)` is cannected ... . D. If Assertion is false but Reason is true.

Description : In the circuit shown below, the current through the inductor is,

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : Does a 10k ohm resistor resist more than a 10 ohm resistor?

Last Answer : Higher values mean more resistance.

Description : What voltage would be measured across the 45 ohm resistor?

Last Answer : Not enough information. But if you know the current, you can useOhm's Law (just multiply the resistance times the current).

Description : What is the phase angle of an ohm inductor in series with an ohm resistor connected to a 5 KHz source?

Last Answer : You need to provide values of resistor and inductor etc to find the phase angle.

Description : The potential difference across a 4 ohm resistor is 20 volts. Assuming that all of the energy dissipated by this resistor is in the form of heat, how many joules of heat are radiated in 10 seconds?  

Last Answer : ANSWER: 1000 JOULES

Description : The constant potential difference across a 2 ohm resistor is 20 volts. How many watts of power are dissipated by this resistor?

Last Answer : ANSWER: 200 WATTS

Description : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C

Last Answer : An amplifier operating over the frequency range from 18 to 20 MHz has 10 kilo ohm input resistor. What is the r.m.s. noise voltage at the input to this amplifier if the ambient temperature is 27o C 18.2 microvolt

Description : In a galvanometer, the deflection becomes one half when the galvanometer is shunted by a 20 ohm resistor. The galvanometer resistance is 

Last Answer : In a galvanometer, the deflection becomes one half when the galvanometer is shunted by a 20 ohm resistor. The galvanometer resistance is 10 Ohm

Description : The colored bands for a 4,700 ohm resistor with a ten percent tolerance are? A.yellow, violet, red, gold B.yellow, violet, orange, gold C.yellow, violet, red, silver D.orange, violet, red, silver

Last Answer : The colored bands for a 4,700 ohm resistor with a ten percent tolerance are? A.yellow, violet, red, gold B.yellow, violet, orange, gold C.yellow, violet, red, silver D.orange, violet, red, silver