Illustrate with neat wiring diagram a single lamp control by two point method.

Illustrate with neat wiring diagram a single lamp control by two point method.
by

1 Answer

Answer :

Single lamp control by two point method: 

image

This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the circuit diagram is as shown in figure above. Assume that the lamp is in between ground floor and first floor with switch S1 is on ground floor and S2 is on first floor. When the position of the switches S1 & S2 is as shown in figure then the lamps is ‘ON’. When a person reaches on first floor the lamp is required to be switched ‘OFF’ so the person will change the position of switch S2, so that the lamp will be switched ‘OFF’.

by

Related questions

Explain the working of HPMV Lamp with neat diagram.

Description : Explain the working of HPMV Lamp with neat diagram.

Last Answer : High-pressure Mercury-Vapour Lamp (HPMVL):  Working:  * Whenever 1-ph, 230V, AC Supply is provided to the discharge tube of MVL, initially the current flows from Phase to the choke to ... : The function of power factor improvement capacitor is to improve the power factor from 0.5 to 0.95.

Explain dynamic and static induced emf with neat diagram.

Description : Explain dynamic and static induced emf with neat diagram.

Last Answer : Dynamically Induced EMF:-  In this case, either coil moves or magnet moves, so that there is relative motion between coil & magnetic field. Thus magnetic field is cut by coil & emf is induced in it. The emf ... The expression for induced EMF is e= -L(di/dt) or = -N(dϕ/dt).

With a neat sketch give the working of shaded pole induction motor.

Description : With a neat sketch give the working of shaded pole induction motor.

Last Answer : Explanation: It has squirrel cage rotor and salient pole stator. The stator poles are shaded partially by short circuited conductor band to create the phase difference between the fluxes emerging from shaded ... rotating magnetic field in the air-gap and torque is exerted on the squirrel cage rotor.

Explain spring control method with neat diagram.

Description : Explain spring control method with neat diagram.

Last Answer : Spring Control Method: As shown in the figure the inner ends of the both springs are attahced to the spindle ,while outer end of upper spring is attached to the lever and outer end of ... the springs are twisted in opposite direction to the motion of pointer and produce controlling torque.

What is PLL? Explain its operation with a block diagram.

Description : What is PLL? Explain its operation with a block diagram.

Last Answer : PLL - A phase-locked loop or phase lock loop is a control system that generates an output signal whose phase is related to the phase of an input signal Block diagram  ... to the input frequency. The phase - locked loop goes through three states free running capture and phase lock.

Explain MCB and ELCB with connection diagram supplying single phase load.

Description : Explain MCB and ELCB with connection diagram supplying single phase load. 

Last Answer : OR OR Explanation: * MCB provides short circuit protection. * MCB provides overload protection * ELCB provides earth fault protection. * MCB is in series with ... occurs, the ELCB cuts off the power within the time of 0.1 sec. automatically to protect the personnel. 

Source transformation Replace the circuit with voltage source in series with a single resistor

Description : Source transformation Replace the circuit with voltage source in series with a single resistor

Last Answer : Source transformation Replace the circuit with voltage source in series with a single resistor

Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter.

Description : Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter. 

Last Answer : Fluorescent lamp:- Operation:- When switch is ON current flows through the choke-filament no1- starter-filament no. 2- to neutral, At that time choke induces high voltage which is applied to ... at the time of starting. ii) Starter: To make and break the circuit to start the tube. 

Describe the working principle of Thyristor operated dimmer with the help of circuit diagram.

Description : Describe the working principle of Thyristor operated dimmer with the help of circuit diagram.

Last Answer : Thyristor operated dimmer: A popular thyristor operated dimmer circuit employ TRIAC-DIAC phase control for low AC power control. During each half-cycle, the capacitor charges through (R1+VR1). When the ... time constant {C (R1+VR1)}. Thus by reducing VR1 the lamp brightness can be increased.

Explain the working of Neon sign tube with diagram.

Description : Explain the working of Neon sign tube with diagram.

Last Answer : Neon sign tube: The construction & circuit diagram for neon tube is as shown in fig. Basically neon tube is used for advertisement or decoration purpose. The maximum length of tube is ... the HT transformer must be earthed separately. * Caution notice of danger board is required.

Compare casing capping wiring with concealed wiring.

Description : Compare casing capping wiring with concealed wiring.

Last Answer : Compare casing capping wiring with concealed wiring: 

Explain with neat sketch the working principle of MIG.

Description : Explain with neat sketch the working principle of MIG.

Last Answer : In metal-arc inert gas welding the Weld area is shielded by an effectively inert atmosphere of argon, helium, carbon dioxide, or various other gas mixtures . The consumable bare Wire is fed automatically ... of the molten-weld puddle. Multiple-weld layers can be deposited at the joint. 

Describe with neat sketch working of hysteresis motor.

Description : Describe with neat sketch working of hysteresis motor.

Last Answer : Working: When stator is energized with single phase ac supply, rotating magnetic field is produced because of starting (auxiliary) and main windings, which remain in circuit permanently. The ... the principle of magnetic locking this motor either rotates at synchronous speed or not at all.

Application one lamp controlled from two places

Description : Application one lamp controlled from two places

Last Answer : Application one lamp controlled from two places: 1. For Stair case wiring 2. Hospital Wiring ( For operating the lamp in room and nursing station) 3. Bedroom Lighting. 

A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

Description : A charge of 0.1 C moves past a given point every 0.01 s. How much is the current?

Last Answer : The current is 10.0A.  1ampere = 1 Coulomb per 1 second.  0.1Coulombs ÷ 0.01seconds = 10.0amperes.

Single point Cutting tool signature

Description : Single point Cutting tool signature

Last Answer : The shape of a tool is specified in a special sequence and this special sequence is called tool signature. The tool signature is given below (i) Back rake angle (ii) Side rake angle (iii) ... rake, end relief, side relief, end cutting edge, side cutting edge angle and 0.8 mm nose radius.

Merits of two wattmeter method

Description : Merits of two wattmeter method

Last Answer : Advantages of Two Wattmeter Method for 3-Phase Power Measurement: 1) It is used for balanced as well as unbalanced load. 2) For the star type load, it is not necessary to ... reactive volt-amperes for balanced loads also. 7) The circuit connections are independent of load connection.

A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Description : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Last Answer : A parallel RLC circuit has the node equation Determine v(t) using the phasor method.

Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Description : Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Last Answer : Operation:  The FM signal which is to be demodulated is applied at the input of the PLL.  the PLL is locked to the FM  The error voltage produced at ... using PLL ensures a high Linearity, between the instantaneous input frequency and VCO control voltage (error amplifier output)

State the meaning of Single line diagram.

Description : State the meaning of Single line diagram.

Last Answer : Meaning of Single line diagram: The single line diagram of a power system is the network which shows the main connections and arrangement of the system components along with their data ( ... breakers, transformers, capacitors, bus bars, and conductors are shown by standardized schematic symbols. 

Explain single line diagram.

Description : Explain single line diagram.

Last Answer : diagram

How to Choose a Birth Control Method

Description : How to Choose a Birth Control Method

Last Answer : How to Choose a Birth Control Method Birth control methods depend on the couple's needs and commitment to the method. Some couples just need to prevent pregnancy while others wish to avoid sexually- ... unplanned sex, a broken condom or failure to take birth control pills two days in a row.

Draw and explain bulk correction method for power factor & control.

Description : Draw and explain bulk correction method for power factor & control.

Last Answer : Bulk correction method for power factor & control: i) Here individual starter controls the capacitors located at distribution panel. ii) Centralized compensation is employed in large industrial plants where many ... capacitor units in steps to maintain P.F. more than preset limit (0.95). 

Write one advantage and one disadvantage each for spring control method and gravity control method.

Description : Write one advantage and one disadvantage each for spring control method and gravity control method.

Last Answer : Advantages of Spring Control Method: 1) The spring-controlled meters may be used in any position. 2) In some instruments, springs can be used as current leads. 3) As springs are light in weight ... only. 2) Scale is non-uniform. 3) Control weights add to the weight of instrument.

The main disadvantage of the Ward-Leonard control method is?

Last Answer : The main disadvantage of the Ward-Leonard control method is high initial cost, high maintenance cost, low efficiency at light loads.

For constant torque drive which speed control method is preferred ?

Last Answer : For constant torque drive armature voltage control speed control method is preferred.

Speed control by Ward Leonard method gives uniform speed variation?

Last Answer : Speed control by Ward Leonard method gives uniform speed variation in both directions.

Explain count up (CTU) instruction with timing diagram.

Description : Explain count up (CTU) instruction with timing diagram.

Last Answer : The CTU is an instruction that counts false-to-true rung transitions. Rung transitions can be caused by events occurring in the program. When rung conditions for a CTU instruction have made a false-to-true ... of Counter up(CTU) Instruction: Too many uploads - please try again in an hour

Describe strain gauge with labelled diagram.

Description : Describe strain gauge with labelled diagram.

Last Answer : A Strain gauge is a sensor whose resistance varies with applied force. It converts force, pressure, tension, weight, etc., into a change in electrical resistance which can then be measured. When external ... to the applied strain. So, the voltmeter can be calibrated in terms of strain or force. 

Draw the labeled block diagram of process control system and explain each block.

Description : Draw the labeled block diagram of process control system and explain each block.

Last Answer : Explanation - Process control system consists of process or plant, sensor, error detector, automatic Controller, actuator or control element. 1) Process or plant- process means some manufacturing sequence ... process which changes the process variable. Output of this block is denoted by u .

The two pressure coils of a single phase power factor meter have?

Last Answer : The two pressure coils of a single phase power factor meter have the same dimensions and the same number of turns.

State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material.

Description : State two applications of : (i) PVC paper (ii) Porcelain with type of class based on withstand temperature is insulating material. 

Last Answer :  (i) Application of PVC paper : 1. It is used in slot lining or motor winding insulation purpose 2. For Insulation of Transformer winding (ii) Application of Porcelain : 1. Mainly used for manufacturing ... on withstand temperature : * H' & C' Class of insulation i e. 180° and above 180°C 

Mesh Analysis with two supermesh

Description : Mesh Analysis with two supermesh

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Nodal Analysis with Voltage Sources dependent voltage source and two supernode

Description : Nodal Analysis with Voltage Sources dependent voltage source and two supernode

Last Answer : Nodal Analysis with Voltage Sources dependent voltage source and two supernode

What is the smallest unit of a compound with the same chemical characteristics?

Description : What is the smallest unit of a compound with the same chemical characteristics?

Last Answer : The molecule is the smallest unit of a compound with the same chemical characteristics.

State the selection criterion of the lamp for various purposes.

Description : State the selection criterion of the lamp for various purposes.

Last Answer : Selection criterion of the lamp for various purposes:  While selecting a lamp for a particular purpose, the available lamps are compared on the basis of following criteria: * Light output ... such as ballasts * Compatibility with the electrical system * Suitability for the operating environment

Define the terms incandescent and incandescent lamp.

Description : Define the terms incandescent and incandescent lamp.

Last Answer : Incandescent is the phenomenon in which the object emits or creates light when it is heated. An incandescent lamp is a lamp in which the filament is heated by electrical current & light is created.

Compare the salient features of LED and CFL based on: i] Lamp Efficiency ii] Life span

Description :  Compare the salient features of LED and CFL based on: i] Lamp Efficiency ii] Life span 

Last Answer : Parameter LED CFL Lamp Efficiency  High (more than 70 lumen per watt) Comparatively less (50-60 lumen per watt) Life span (in working hours) 10000 3000

With neat diagram explain calibration of energy meter by direct loading method.

Description : With neat diagram explain calibration of energy meter by direct loading method.

Last Answer : Calibration of Energy Meter by Direct Loading Method:  There are three methods for testing/calibration:  1. Long period dial test  2. Using rotary sub- standard meter  3. Using precision grade instruments  All ... of substandard meter in kWh  Then % error = [(D - DS)/DS] x 100

State two types of Electronic dimmer.

Description : State two types of Electronic dimmer.

Last Answer : Two types of electronic dimmers are: 1) S.C.R. operated dimmer 2) Triac operated dimmer 

Sound Technical advice for wiring a room that already has a sconce light for a ceiling fixture?

Description : Sound Technical advice for wiring a room that already has a sconce light for a ceiling fixture?

Last Answer : If the wall is an interior wall then it should be an empty cavity. If it is an old home you may have fire stops inside the walls that will be a dead end when you attempt to fish the wire down. Make ... a good idea to know how much load is already on the circuit if you want to still use the sconce.

Wiring – types

Description : Wiring – types

Last Answer : Ans) a. Casing & Capping b. Concealed wiring c. Cleat Wiring d. Conduit Wiring – Cutting of wall.

How to replace the electrical wiring in the apartment?

Description : How to replace the electrical wiring in the apartment?

Last Answer : How to replace the electrical wiring in the apartment? In most cases, when renovating an apartment, a complete replacement of the electrical wiring is required, especially if the house was built in ... Upon completion of the finishing, the new electrical wiring in your apartment is ready for use.

State different types of holders used in wiring installation.

Description : State different types of holders used in wiring installation.

Last Answer : Following types of holders used in wiring installation: 1. Pendent Holder 2. Batten Holder 3. Angle holder 4. Screwed holder 

Name safety tools used in industry for electrical wiring.

Description : Name safety tools used in industry for electrical wiring.

Last Answer : Safety tools used in industry for electrical wiring : 1) Hand gloves 2) Goggles 3) Rubber mats 4) Fire extinguishers 5) Danger notice plates 6) Search lights 7) Safety shoes or Gumboots 8) Ear plugs ... belts 13) Safety mask 14) Fire buckets 15) First aid box 16) Insulating stick or discharge rod

List any four wiring accessories and its function.

Description : List any four wiring accessories and its function. 

Last Answer : Following wiring accessories: 1) Lamp holder: It is the holding accessory. The different types of holders used such as angle holder, batten holder, pendent holder 2) Ceiling Rose: Ceiling rose are of two types: ... etc 9) Switch board, ICDP Main Switch 10) All types of size of VIR & PVC wire

List the types of Internal wiring in residential installations –

Description : List the types of Internal wiring in residential installations –

Last Answer : 1) Cleat wiring 2) Batten wiring 3) Wooden casing capping wiring 4) PVC conduit wiring 5) PVC casing capping wiring 6) Concealed wiring

State the purpose of lighting control. List the different types of dimmer.

Description : State the purpose of lighting control. List the different types of dimmer.

Last Answer : Purpose of Lighting Control:- 1. To turn ON or OFF the lamps 2. For dimming: The dimming control permits the adjustment of lighting over a range. 3. For changing the lighting levels ... operated dimmer 6) Triac operated Dimmer 7) PWM (Pulse width modulation) Controlled technique.

Neat Uses for Milk Jugs

Description : Neat Uses for Milk Jugs

Last Answer : Milk jugs, at first glance, appear as molded receptacles built only to carry milk, water and small objects. As a result, people usually throw away the durable milk containers upon consuming their contents. ... details. In the end, you might be writing your own list of personal milk jug discoveries.

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.