Enlist the luminaries used in factory lighting and lux level required in various areas.

Enlist the luminaries used in factory lighting and lux level required in various areas.
by

1 Answer

Answer :

Area
Luminaries
Lux level
Office building
Fluorescent tube, LED, CFL
500 lux
Testing centre
Fluorescent tube, LED, CFL
400 to 500 lux
Workshop/work place
Halogen lamp, mercury vapour lamp, sodium vapour lamp
Above 5000 lux
Research and development center
Fluorescent tube, LED, CFL
500 to 600 lux
Outdoor area/parking area
Mercury or sodium vapour lamp
1000 to 2000 lux
Quality control department
Fluorescent tube, LED, CFL 
600 to 700 lux 
Sales department
Fluorescent tube, LED, CFL
300 to 400 lux
Commissioning department
Fluorescent tube, LED, CFL
400 to 500 lux
Small Store Room Without sunlight 
Fluorescent tube, LED, CFL, Projector lamp, filament lamp, Halogen Lamp, Metal Halide lamp etc
200-300 Lux
Highbay area
Fluorescent tube, LED, CFL, Projector lamp, filament lamp, Halogen Lamp, Metal Halide lamp etc
Above 600 Lux
by

Related questions

State the various lighting calculations methods and Describe any one of them.

Description : State the various lighting calculations methods and Describe any one of them.

Last Answer : Lighting calculation methods: 1. Lumens or Light flux method 2. Point to point or Inverse Square law method 3. Watts per Square meter method i) Lumens or Light ... is taken according to the illumination desired on an average value considering overall efficiency of the lighting system.

State the different types of outdoor flood lighting and where are they used.

Description : State the different types of outdoor flood lighting and where are they used.

Last Answer : There are three types of projectors used for flood lighting :  a) Narrow beam Projector b) Medium angle Projector c) Wide angle Projector a) Narrow beam Projectors: - Light beam with such ... yards, stadiums, car parking area etc. 3) It is used for illuminating advertisements, boarding's etc.

Explain the lighting scheme to be designed for each of the following: i) Special ward in hospitals ii) Dentist’s Cabin

Description : Explain the lighting scheme to be designed for each of the following: i) Special ward in hospitals ii) Dentist’s Cabin 

Last Answer : i) Special ward in hospital: For the patients in the wards, lighting should create a cozy and pleasant atmosphere. Lighting in the wards should be planned in such a way that it meets the specific ... we use such as cements and bonding agents that we use to restore your teeth back to health.

State the insulating materials used in motor. Write temperature class and withstand temperature ranges for them.

Description : State the insulating materials used in motor. Write temperature class and withstand temperature ranges for them. 

Last Answer : The insulating materials used in motor are as belows: 1. Cotton, 2. Silk, or paper, 3. Press board, 4. Resins 5. PVC 6. Cellulose-Fiber, 7. Enameled coating, etc  ... Over 180° Mica, porcelain, ceramics, glass quartz, asbestos, treated glass fiber or treated asbestos. etc.

Define armature reaction in an alternator. Explain the effect of armature reaction at various P.F. of loads of alternator.

Description : Define armature reaction in an alternator. Explain the effect of armature reaction at various P.F. of loads of alternator.

Last Answer : Armature Reaction: The effect of armature flux on main flux is called as armature reaction.  Armature Reaction at Various Power Factors: When armature is loaded, the armature flux modifies ... lagging p.f. For capacitive loads the effect of flux is partly distorting and partly strengthening.

State the selection criterion of the lamp for various purposes.

Description : State the selection criterion of the lamp for various purposes.

Last Answer : Selection criterion of the lamp for various purposes:  While selecting a lamp for a particular purpose, the available lamps are compared on the basis of following criteria: * Light output ... such as ballasts * Compatibility with the electrical system * Suitability for the operating environment

State the purpose of lighting control. List the different types of dimmer.

Description : State the purpose of lighting control. List the different types of dimmer.

Last Answer : Purpose of Lighting Control:- 1. To turn ON or OFF the lamps 2. For dimming: The dimming control permits the adjustment of lighting over a range. 3. For changing the lighting levels ... operated dimmer 6) Triac operated Dimmer 7) PWM (Pulse width modulation) Controlled technique.

Explain the features of Aquarium lighting.

Description : Explain the features of Aquarium lighting. 

Last Answer : 1) The aquarium light depends upon the size of the aquarium tank (Length, width and depth)  2) The aquarium lighting depends upon the all surrounding condition e.g. colour and size of the given ... The aquarium lighting should be economical.  9) The life of the aquarium lighting should be long. 

Evaluate the following quantities and express your results in polar form

Description : Evaluate the following quantities and express your results in polar form

Last Answer : Evaluate the following quantities and express your results in polar form

Evaluate the following complex numbers and leave your results in polar form

Description : Evaluate the following complex numbers and leave your results in polar form

Last Answer : Evaluate the following complex numbers and leave your results in polar form

Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced. 

Compare the AC and DC Arc lamps.

Description : Compare the AC and DC Arc lamps.

Last Answer : AC Arc Lamp DC Arc Lamp Cross section area of electrode is same Cross section area of electrode is positive rod is twice that of negative rod Series inductor is used for stability ... supply is used for DC arc lamp Luminous efficiency is less Luminous efficiency is high

Define the terms incandescent and incandescent lamp.

Description : Define the terms incandescent and incandescent lamp.

Last Answer : Incandescent is the phenomenon in which the object emits or creates light when it is heated. An incandescent lamp is a lamp in which the filament is heated by electrical current & light is created.

Compare the salient features of LED and CFL based on: i] Lamp Efficiency ii] Life span

Description :  Compare the salient features of LED and CFL based on: i] Lamp Efficiency ii] Life span 

Last Answer : Parameter LED CFL Lamp Efficiency  High (more than 70 lumen per watt) Comparatively less (50-60 lumen per watt) Life span (in working hours) 10000 3000

Define Enhance lighting.

Description : Define Enhance lighting.

Last Answer : Enhance lighting: Enhance lighting is the lighting with various colour effect and controlled light intensity, used for decoration and effective visualization of gold, silver, diamond and watches showroom purpose.

List standard voltage level used in India.

Description : List standard voltage level used in India. 

Last Answer : Standard voltage level used in India: * Generation Voltage : 3.3KV, 6.6KV,11KV and 17.5 KV,21KV (Now a days generation voltage is in the range of 11KV- 33KV) * Primary Transmission voltage :- 220 ... voltages in India are 765 KV (750KV), 400KV, 220KV, 132KV, 110KV, 66KV, 33KV, 22KV, 11KV.

Describe different RT level computational and sequential components used to design single function processors.

Description : Describe different RT level computational and sequential components used to design single function processors.

Last Answer : RT-level combinational components:- To reduce the complexity in digital logic, combinational components are used, which are more powerful than logic gates.  Such combinational ... during a clock edge. An asynchronous inputs value effects the circuit independent of the clock.

State any two advantages of MCB over Fuse. State the standard specifications of MCB available in the market.

Description : State any two advantages of MCB over Fuse. State the standard specifications of MCB available in the market.  

Last Answer : Following advantages of MCB over Fuse: 1. No need of replacement of fuse wire. 2. Manually restore of supply is simple. 3. Fault understanding by visual inspection 4. More safe than fuse The standard specifications of ... 6A, 10A,16A,20A, 25A, 30A, 32A, 40A, 50A, 60A and 63A 6. 250V and 450 v

State the modification to be done in dc series motor to work satisfactorily as ac series motor. State applications of ac series motor.

Description : State the modification to be done in dc series motor to work satisfactorily as ac series motor. State applications of ac series motor.

Last Answer : Modifications are necessary in a dc series motor so that it operates satisfactorily on ac supply. The modifications are as follows:  1) AC series motor is built with a few field turns as ... and grinders 5) High speed vacuum cleaners 6) Sewing machines 7) Food processors 8) Drilling machine 

State the losses in secondary distribution system.

Description : State the losses in secondary distribution system. 

Last Answer : The losses in secondary distribution system: a) Technical losses: 1. Due to poor voltage 2. Due to unbalance load 3. Due poor quality of transformer & its components 4. Due to poor quality ... of induction type of energy meter. 3. Lack of administration. 4. Energy theft 5. Unmetered supply

List the energy conservation technique in induction motor.

Description : List the energy conservation technique in induction motor. 

Last Answer : Following are the list of energy conservation techniques in electrical motors: 1) Reduction in iron losses by using low loss silicon steel core material laminated to thinner dimension. 2) Using bigger length ... at light load. 13) By rewinding in induction motor 14) By motor survey

Sinusoidal Steady-State Analysis - Using nodal analysis, find node voltages in the circuit.

Description : Sinusoidal Steady-State Analysis - Using nodal analysis, find node voltages in the circuit.

Last Answer : Sinusoidal Steady-State Analysis - Using nodal analysis, find node voltages in the circuit.

Using phasors, determine in the following equations

Description : Using phasors, determine in the following equations

Last Answer : Using phasors, determine in the following equations

Express the following functions in cosine form

Description : Express the following functions in cosine form

Last Answer : Express the following functions in cosine form

Source transformation Replace the circuit with voltage source in series with a single resistor

Description : Source transformation Replace the circuit with voltage source in series with a single resistor

Last Answer : Source transformation Replace the circuit with voltage source in series with a single resistor

Is the power line voltage available in our homes a dc or an ac voltage?

Description : Is the power line voltage available in our homes a dc or an ac voltage?

Last Answer : The power line voltage available in our homes is AC. Mobile dwellings are the most commonly DC-supplied homes and even then they tend to include AC supply for heavier loads.

State different types of holders used in wiring installation.

Description : State different types of holders used in wiring installation.

Last Answer : Following types of holders used in wiring installation: 1. Pendent Holder 2. Batten Holder 3. Angle holder 4. Screwed holder 

Define Feed and speed in shaping machine

Description : Define Feed and speed in shaping machine

Last Answer : 1) Feed: Feed (S) is the relative movement of the work or tool in a direction perpendicular to the axis of reciprocation of the ram per double stroke. It is expressed in mm per stroke. 2) Speed: ... speed is the speed at which the metal is removed by the cutting tool in a period of one minute.

Calculate these complex numbers and express your results in rectangular form

Description : Calculate these complex numbers and express your results in rectangular form

Last Answer : Calculate these complex numbers and express your results in rectangular form

XL and XC in parallel

Description : XL and XC in parallel

Last Answer : https://youtu.be/fCN95EiEWDI

X L and X C in Series

Description : X L and X C in Series

Last Answer : Inductive reactance X L and Capacitive reactance X C in series. Inductive reactance X L of value 60 ohm and Capacitive reactance X C of value 40 ohm are connected in series. 120 volts A C voltage is ... . The current will be 6 ampere. This time current will lead the voltage by 90 degree.

In what areas is concrete used?

Description : In what areas is concrete used?

Last Answer : Concrete is the oldest building material, which began to be used in ancient civilizations. Due to centuries of development, today's concrete is a very high-quality building material and has a fairly ... is to understand in advance some of the nuances and understand what kind of material is needed.

State the material used for making (1) Magnetic Core (2) Fuse element

Description : State the material used for making (1) Magnetic Core (2) Fuse element  

Last Answer : The material used for making of:  (1) Magnetic Core : Iron, cobalt, Nickel, CRGO, HRGO , silicon steel  (2) Fuse Element: Tin- lead wire, Tinned copper wire 

Explain the suitability of aluminium as an electrical conductor with respect to its mechanical and electrical properties.

Description : Explain the suitability of aluminium as an electrical conductor with respect to its mechanical and electrical properties. 

Last Answer : Following are requirements of conductor:- i) High conductivity :  Material should have high conductivity, So that * cross section of conductor (size) reduces, * Copper losses reduces, * So Efficiency ... . Boiling point is 1820°C 9. Specific gravity is 2.7 10. High resistance to corrosion. 

State the type of insulating materials under Class Y and Class B.

Description : State the type of insulating materials under Class Y and Class B.

Last Answer : The type of insulating materials under Class Y : 1. Cotton  2. Silk 3. Paper 4. Rubber 5. PVC The type of insulating materials under Class B: 1. Backelite 2. Impregnated varnish 3. Mica 4. Fiber glass 5. Asbestos 

State the impact of inductance and resistance on transmission line performance

Description : State the impact of inductance and resistance on transmission line performance

Last Answer : Impact of inductance on transmission line: 1) It causes IXL drop in transmission line which affects regulation. 2) It is the only parameter which decides power transmission capacity of line i. ... is very small, it causes losses, temperature rise& poor voltage regulation so it cannot be neglected

State the needs and benefits of star labelling.

Description : State the needs and benefits of star labelling. 

Last Answer : Needs of star labelling: * Star labelling is meanly required to recognize quality of product * Star labelling is also required to determine life and efficiency of the product. * Star labels ... emission and air pollution will be reduces. 5. Market efficiency and compilation will be improve. 

State the difference between energy conservation and energy audit.

Description : State the difference between energy conservation and energy audit. 

Last Answer : energy conservation Energy audit It is reducing the growth of energy consumption by avoiding unnecessary usage of energy It is an inspection, survey & analysis of energy flows ... Various measuring instruments, with proper sensing elements are required for the energy audit. 

Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

Give the function of fuse and switch.

Description : Give the function of fuse and switch.

Last Answer : Functions of fuse:  * To break the circuit under fault condition.  * To provide overcurrent protection to the circuit.  * To provide short circuit protection to the circuit.  * To provide ...  * To make the electric circuit manually.  * To break the electric circuit manually.

Explain the concept of lagging and leading phase angle by waveform.

Description : Explain the concept of lagging and leading phase angle by waveform.

Last Answer : i) Leading phase angle :  When two ac quantities of same frequency do not attain their respective zero or peak values simultaneously, then the quantities are said to be out-of-phase quantities. The ... Similarly, in the second diagram, the voltage is said to be lagging the current by  Φ.

Describe the difference between an open circuit and a short circuit.

Description : Describe the difference between an open circuit and a short circuit.

Last Answer : Open circuit means the wire is cut meaning power will not flow and close circuit means wire is not cut and hence power will flow.Short circuit is the same as close circuit

The number of loop equations required to completely analysing a network comprising of 8 independent

Description :  The number of loop equations required to completely analysing a network comprising of 8 independent branches and 6 nodes including the reference node shall be A) 3 B) 2 C) 4 D) 5 

Last Answer :  The number of loop equations required to completely analysing a network comprising of 8 independent branches and 6 nodes including the reference node shall be 3 

Equilizer rings are required in case armature is?

Last Answer : Equilizer rings are required in case armature is lap wound.

Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Description : Select insulating materials for following parts : (i) Insulation between heating element and base plate of electric iron. (ii) Insulation used over copper or aluminium conductor used for making coils. (iii) Transformer bushings. (iv) Insulation between transmission line and pole.

Last Answer : Parts Insulating Materials  Insulation between heating element and base plate of electric iron. Mica Insulation used over copper or aluminium conductor used for making coils.  ... Transformer bushings Porcelain  Insulation between transmission line and pole. Porcelain

State various effects of electric current and explain any one.

Description : State various effects of electric current and explain any one.

Last Answer : Effects of Electric Current:  1. Magnetic Effect: When a current is passed through a conductor, magnetic field is produced round the conductor. Due to this field when current carrying ... The rise in temperature is converted into elongation of hot wire element causes displacement of pointer. 

Explain the various steps involved in designing a custom single-purpose processor.

Description : Explain the various steps involved in designing a custom single-purpose processor.

Last Answer : A single purpose processor is a digital circuit designed to execute exactly one program. It is also known as co-processor, accelerator or peripheral. It contains only ... for small quantities. Performance may not match general-purpose processors for same applications.

What is your favourite type of lighting?

Description : What is your favourite type of lighting?

Last Answer : multicolored Christmas lights on the tree… with different sections blinking at different intervals (most of you may say that’s tacky, but it’s a childhood thing)

How To Make A Landscape Lighting

Description : How To Make A Landscape Lighting

Last Answer : You have just finished arranging the landscape of your home's lawn. As you are about to marvel at the beauty of your creation, nighttime comes and spoils your proud moment. You want to stammer and ... lights won't turn on, you can reconnect or switch the wires with your supply of electric wire.

How to match lighting for different rooms?

Description : How to match lighting for different rooms?

Last Answer : How to match lighting for different rooms? Designers claim that the "mood" of any apartment is created with the help of light. When choosing lighting for a particular room, some rules ... to avoid touching them with wet hands. Internal switches must also be carefully protected against moisture.