List out factors affecting proximity effect. 

1 Answer

Answer :

Factors affecting proximity effect:

1. Conductor size (diameter of conductor)

2. Frequency of supply current.

3. Distance between conductors.

4. Permeability of conductor material 

Related questions

Description : State the factors affecting hysteresis loss.

Last Answer : i) Flux density ii) Frequency iii) Volume of the magnetic material iv) Nature of magnetic material

Description : State the meaning of ferranti effect and proximity effect.  

Last Answer : i) Ferranti effect : When long distance transmission is lightly loaded or there is no load condition than it is observe that receiving end voltage (VR) is found to be greater than sending end ... on conductor causes current in each conductor is re-distributed. This is known as proximity effect.

Description : State the various factors governing selection of site for TPS. 

Last Answer : Following various factors governing selection of site for TPS.:- 1. It should locate near coal mines. 2. Sufficient quantity of water should be available. 3. Sufficient large space should ... availalbe nearly. To the extent possible, the thermal station should be far away from an aerodrome   

Description : State and explain any four factors governing selection of induction motor.

Last Answer : The factors governing the selection of Induction motor: 1) Load torque required at normal speed matches with available torque of motor. 2) Break down torque or pull out torque or maximum torque ... If selecting energy efficient motor the cost benefit analysis over the long run must be worked out.

Description : State two factors deciding size of conduit.

Last Answer : Following factors deciding size of conduit: 1) Types of wiring method 2) No. of wires carried out through conduit 3) Size of wires required for sub circuits which is carried out through conduit 4) Future expansion.

Description : State any four factors for selection of hydro power plant site. 

Last Answer : Following Factors to be kept while site selecting for Hydro power plant: 1) Quantity of water available :-Where high rainfall occures so that sufficent quantity of water can be stored for generation of ... be possible to divert the stream. 11. Sand, gravel, etc., should be available nearby.

Description : State any four factors for selection of site of wind power plant.

Last Answer : The Factors for selection of site for Wind Mills: 1) The site should be selected where winds are strong i.e. where pressure of wind is high and there is continuity (14.4- 16.2 km/h) ... 50m of the turbine which can affect the system's overall performance 10)Possibility to connect to power grid. 

Description : State any four factors for selecting location of nuclear power plant.

Last Answer : i) Seismicity: If the area of a nuclear site is seismically active, it may not be used for nuclear power plant.  ii) Water Availability: The nuclear power plants would need a ... Therefore, the site selected for such plant should have adequate arrangement for the disposal of radioactive waste.

Description : State any four factors governing Selection of site for thermal power station. 

Last Answer : Following Factors are to be considered:- 1. It should locate near coal mine. 2. Sufficient quantity of water should be available. 3. Sufficient large space should be available. 4. It should be located ... laws of the land and the town planning. 14. The interests of national defense must be served.

Description : Write any two factors on which earth resistance depends.

Last Answer : Factors on which earth resistance depends: (1) The shape and material used for the electrode (2) Depth of the electrode in the ground. (3) The specific resistance of the soil around the electrode (4) Moisture content in the soil. (5) Nature of soil 

Description : The main disadvantages of having poor power factors are:  (A) High cost of station and distribution equipment (B) Poor voltage regulation (C) High energy loss in conductor (D) All of the above

Last Answer : The main disadvantages of having poor power factors are:  (A) High cost of station and distribution equipment (B) Poor voltage regulation (C) High energy loss in conductor (D) All of the above

Description : What are the factors influencing measurement errors?

Last Answer : The factor influencing measurement errors are accuracy, precision, range and bandwidth, sensitivity, resolution and uncertainty.

Description : The Semiconductor strain gauges typically have much higher gauge factors than those of metallic strain gauges, primarily due to : (A) higher temperature sensitivity (B) higher Poisson’s ratio (C) higher piezoresitive coefficient (D) higher magnetostrictive coefficient

Last Answer : The Semiconductor strain gauges typically have much higher gauge factors than those of metallic strain gauges, primarily due to : higher piezoresitive coefficient

Description : What factors affect resistivity?

Last Answer : 1)type of material 2)temperature 3)length and area of cross section of conductor

Description : How to Work Out Using Wii Fit

Last Answer : How to Work Out Using Wii Fit Nintendo Wii is a relatively new console that allows for fun, interactive games. The makers of this amazing piece of technology realized that it can be more than just ... rid of vices and generally being good to yourself. Only then will you notice changes in yourself.

Description : How to Lose Weight Without Working Out

Last Answer : How to Lose Weight Without Working Out Weight loss is a major concern among many people. Whether a person is obese or just wants to shed a few extra pounds, keeping fit and trim is an important ... still lose excess pounds with just a few activities that don't involve a lot of sweating and toning.

Description : Explain the activities carried out during weekly maintenance of 3 ph. Induction motor. 

Last Answer : Activities Carried out During Weekly Maintenance of 3 ph. Induction Motor:  1) Check belt tension. In cases where this is excessive it should immediately be reduces and in the case of sleeve ... and cooled by oil mist systems its important to check the oil mist flow paths/pressure components.

Description : With the help of neat diagram, describe the procedure to carry out phasing out test on a 3 phase transformer. Also state the purpose of conducting this test on 3 phase transformer.

Last Answer : i) This test is carried out on 3-ph transformer to identify primary & secondary winding belonging to the same phase. ii) As shown in fig above all primary & secondary phases ... of this test is to check the respective phases of primary & secondary windings in 3-ph transformer

Description : Why phasing out and polarity test is carried out on three phase transformer?

Last Answer : The phasing out test is carried out to identify the windings (primary and secondary) of corresponding phase of the three phase transformer. The polarity test is carried out to identify the ... identical polarity of the primary and secondary windings of each phase of the three phase transformer.

Description : What can I use in place of laundry detergent?

Last Answer : I never tried this but I am wondering if you put the clothes in the machine (just this once) and just ran the machine, if it would do (again, doing it just one time). Of course, if you had stains on the clothes, they may or may not come out, depending on what they were.

Description : I have generalized anxiety disorder and I want to make a list of simple things that a person in my situation should do in order to get out of their comfort zone. Any ideas?

Last Answer : Can you give us a little more information. How does your anxiety manifest itself and are there any specific triggers that bring on attacks? Also, when you say get out of your comfort zone, are you looking for ideas to help you build your resilience in order to lessen the likelihood of attacks?

Description : When will we see Ghislaine Maxwell's list?

Last Answer : We won’t!!! She said that SHE would no longer fight to keep the list private. She said NOTHING about the people on the list stopping it from becoming public knowledge. Somebody’s pockets are being lined even as we speak!!!

Description : What's on your Murtaugh List?

Last Answer : answer:Crop tops not at my age and not after having a babe High heels bunions suck…so do flat feet but I already had those before I got too old

Description : Who was on your top ten most fanciable list when you were a teenager, assuming you had one of course?

Last Answer : Oh my word, who didn’t/don’t I fancy in the world of fame, fortune and showbiz. Mark Hoppus, bassist for Blink-182 is probably my number one. Oh and River Phoenix definitely, not forgetting Macaulay Culkin.

Description : List variable flow meter. 

Last Answer : 1. Variable area : Rotameter 2. Variable head : a) Venturi b) Orifice c) Pitot tube d) Nozzle

Description : List any four casting defects.

Last Answer : The various types of casting defects are as follows: 1. Gas Porosity: Blowholes, open holes, pinholes. 2. Shrinkage defects: shrinkage cavity. 3. Mold material defects: Cut and washes, ... Pouring metal defects: Cold shut, misrun, slag inclusion. Metallurgical defects: Hot tears, hot spot.

Description : List any four materials used for pattern making

Last Answer : The various types of materials used are as follows: 1. Wood 2. Metal. 3. Plastic. 4. Plaster. 5. Wax.

Description : List any four accessories used on lathe.

Last Answer : The various accessories used in lathe are as follows. 1) Lathe centers 2) Carriers or driving dog 3) catch plates 4) Chucks 5) Face plates 6) Angle plates 7) Mandrels 8) Rests

Description : List types of chips produced in machining process.

Last Answer : The various types of chips produced in machining process are as follows: 1. Continuous chips: According to its name, continuous chips have a continuous segment. . 2. Discontinuous chips or segmental chips: ... chip is same as the continuous chips except a built edge is form at the face of tool.

Description : List different starting methods of three phase synchronous motor. Explain any one of them.

Last Answer : Different Starting Methods of Three Phase Synchronous Motor: As synchronous motor is not self starting, different methods of starting are as follows: 1) By using an Induction (Pony) motor 2) ... . The rotor gets pulled into synchronism and starts running at constant speed as a synchronous motor. 

Description : List applications of stepper motor.

Last Answer : Applications of Stepper Motor: 1) Computer controlled systems 2) Numerical control of machine tools 3) Tape drives 4) Floppy disc drives 5) Computer printers 6) X-Y plotters 7) ... ) Extruders 21) Engravers 22) Analytical and Medical instruments 23) Embroidery Machines 24) Packaging Machines

Description : List different torques in synchronous motor. 

Last Answer : Different Torques in Synchronous Motor: 1) Starting torque 2) Running torque 3) Pull-in torque 4) Pull-out torque

Description : List types of timers.

Last Answer : Types of Timers: Retentive Timers: 1. ON Delay 2. OFF Delay Non Retentive Timers: 1. ON Delay 2. OFF Delay

Description : List the different types of tariff.

Last Answer : Various types of Tariff:-  1) Flat-demand Tariff  2) Simple-demand Tariff or Uniform Tariff  3) Flat-rate Tariff  4) Step-rate Tariff  5) Block-rate Tariff  6) Two-part Tariff  7) Maximum demand Tariff ... c) KW and KVAR Tariff 10) TOD (Time of Day) Tariff 11) TOU ( Time of Usage) Tariff

Description : List the energy conservation technique in induction motor. 

Last Answer : Following are the list of energy conservation techniques in electrical motors: 1) Reduction in iron losses by using low loss silicon steel core material laminated to thinner dimension. 2) Using bigger length ... at light load. 13) By rewinding in induction motor 14) By motor survey

Description : List  functions of MEDA. 

Last Answer : Functions of MEDA:  1. To decide long term energy conservation policy's for Maharashtra state. 2. To coordinate with central government organization i.e NPC, MNRE etc for energy conservation policy ... our society. 6. To decide penalty, incentive, subsidy for energy conservation at state level. 

Description : State the purpose of lighting control. List the different types of dimmer.

Last Answer : Purpose of Lighting Control:- 1. To turn ON or OFF the lamps 2. For dimming: The dimming control permits the adjustment of lighting over a range. 3. For changing the lighting levels ... operated dimmer 6) Triac operated Dimmer 7) PWM (Pulse width modulation) Controlled technique.

Description : List specification of BJT.

Last Answer : * The bipolar junction transistor (BJT) has small signal current gain, α (hfb). * Maximum collector current Ic (max). * Maximum collector to emitter voltage, VCE (max). * Collector to emitter ... . * Collector to emitter cut off voltage, VCEO. * Base emitter saturation voltage, VBE (sat).

Description : List the main parts of D.C. motor

Last Answer : Main parts of D.C. motor and their functions:  Part Functions Yoke i) Provides mechanical support for poles. ii) Acts as protecting cover for machine. iii) Carries magnetic flux. ... a fixed physical position relative to the stator.  Shaft Used to transfer mechanical power 

Description : List different types of stepper motor. State one application of stepper motor.

Last Answer : Types of stepper motor : (i)Variable - reluctance motor (ii) Permanent- magnet motors (iii) Hybrid motors. Applications of stepper motor : In robotics, In CNC machines, In computers, printers, ... In Watches, In biomedical applications such as X-ray machines, CT scan, In Process control systems. 

Description : List applications of servomotor.

Last Answer : Applications of Servomotor: 1) Computers 2) Robotics and toys 3) CD/DVD players 4) Textile industries 5) Instrument servos 6) Tracking and guidance system 7) Self-balancing recorders 8 ... 9) Process controllers 10) Electromechanical actuators 11) Air-craft control system 12) Programming device

Description : List at least two examples that show how static electricity can be generated.

Last Answer : Examples of how static electricity can be generated include combing your hair, walking across a carpeted room, or sliding two pieces of plastic across each other.

Description : List specification of zener diode

Last Answer : 1. Zener Voltage 2. Maximum Zener current 3. Power dissipation 4. Operating temperature 5. Dynamic Resistance 

Description : How could I get a flashing effect for video wallpaper?

Last Answer : The picture is hidden behind a login form, could you put it on, say, imageshack.us?

Description : How Does Obesity Effect Diabetes ?

Last Answer : How Does Obesity Effect Diabetes Obesity and diabetes are two diseases that are cause for serious concern among many Americans. Every year, more and more overweight and obese people run the risk of developing ... , you can win the battle against obesity, and save your own life at the same time.

Description : Piezo-electric effect

Last Answer : Piezoelectric Effect is the ability of certain materials to generate an electric charge in response to applied mechanical stress. The word Piezoelectric is derived from the Greek piezein, which means to squeeze or ... Storage Temperature Range: -55 to + 125°C Insulation Resistance: 500 M ohms

Description :  State the disadvantages of skin effect.

Last Answer : Disadvantages of skin effect:- 1. Full cross section of conductor is not utilized, Therefore effective area of conductor reduces so its resistance increases. 2. Due to increase in resistance, copper ... increases (Since Voltage drop = IR ) 5. So voltage regulation becomes poor (increases) 

Description : State the meaning of skin effect and how can it be minimised. 

Last Answer : Meaning of skin effect :  When alternating current flows through conductor it has tendency to flow away from center of conductor. i.e. maximum current density is near skin of conductor and goes on ... whenever possible as Skin effect is absent (Since frequency 0) instead of A.C. supply.  

Description : Define armature reaction in an alternator. Explain the effect of armature reaction at various P.F. of loads of alternator.

Last Answer : Armature Reaction: The effect of armature flux on main flux is called as armature reaction.  Armature Reaction at Various Power Factors: When armature is loaded, the armature flux modifies ... lagging p.f. For capacitive loads the effect of flux is partly distorting and partly strengthening.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced.