Dynamic vibration absorber is suitable for
A. Constant speed machines
B. Varying speed machines
C. Zero speed range machines
D. None of the above

1 Answer

Answer :

A. Constant speed machines

Related questions

Description : Dynamic vibration absorber is suitable for A varying speed machines B constant speed machines C Zero speed range machines D None of the mentioned

Last Answer : B constant speed machines

Description : Dynamic vibration absorber is suitable for A) Constant speed machine B) Varying speed machine C) zero speed machine D) None of the above

Last Answer : A) Constant speed machine

Description : In a dynamic vibration absorber system, under tuned conditions which of the following relation holds good? A K 1 K 2 =M 1 M 2 B K 1 M 2 =M 1 K 2 C K 1 M 1 = K 2 M 2 D none of the mentioned

Last Answer : B K 1 M 2 =M 1 K 2

Description : The two resonant frequency ratio (ω/ ω2) in a dynamic vibration absorber system for a mass ratio 0.2 are given by A) 0 ; 1.0 B) 0.801 ; 1.248 C) 0.458 ; 1.124 D) 0.642 ; 1.558

Last Answer : B) 0.801 ; 1.248

Description : Centrifugal absorber is used to reduce A) Centrifugal force in rotating system B) Torsional vibration of rotating system C) Vibration in linear system D) Transverse vibrations

Last Answer : B) Torsional vibration of rotating system

Description : Which of the following condition should be satisfied in the design of a vibration absorber ? A) Natural frequency of the auxiliary system should be equal to the natural frequency of the main ... D) Natural frequency of the auxiliary system should be twice natural frequency of the main system

Last Answer : A) Natural frequency of the auxiliary system should be equal to the natural frequency of the main system

Description : When ≠ , the absorber is known as A. Untuned vibration absorber B. Tuned vibration absorber C. Both of above D. None of these

Last Answer : A. Untuned vibration absorber

Description : When = , the absorber is known as A. Untuned vibration absorber B. Tuned vibration absorber C. Both of above D. None of these

Last Answer : B. Tuned vibration absorber

Description : Frequency of centrifugal pendulum absorber is always proportional to A) Oscillating motion B) Transfer motion C) Speed of rotating body D) All of the above

Last Answer : C) Speed of rotating body

Description : In vibration isolation system, if ω/ωn < 2, then for all values of damping factor, the transmissibility will be A less than unity B equal to unity C greater than unity D zero

Last Answer : C greater than unity

Description : What is meant by node point? A. The point at which amplitude of vibration is maximum B. The point at which amplitude of vibration is minimum C. The point at which amplitude of vibration is zero D. None of the above

Last Answer : C. The point at which amplitude of vibration is zero

Description : If ωmax is the frequency at which the peak amplitude occurs and ωn is the natural frequency of the system then In a forced vibration system with damping, the higher the damping, A) More will be ... and ωmax is independent of damping in this system D) The difference between ωn and ωmax will be zero

Last Answer : A) More will be the difference between ωn and ωmax

Description : A node means a section where the amplitude of vibration is A. Maximum B. Half of the maximum C. Zero D. 1⁄4 of the maximum

Last Answer : C. Zero

Description : When the frequency of external exciting force is equal to the natural frequency of the vibration of the system A. The amplitude of vibration is zero B. The amplitude of vibration is significantly small C. The amplitude of vibration is very large D. The amplitude does not change

Last Answer : C. The amplitude of vibration is very large

Description : In vibration isolation system, if ω/ω n < 2, then for all values of damping factor, the transmissibility will be a) less than unity b) equal to unity c) greater than unity d) zero

Last Answer : c) greater than unity

Description : In vibration isolation system, if ω/ω n < 2, then for all values of damping factor, the transmissibility will be a) less than unity b) equal to unity c) greater than unity d) zero

Last Answer : c) greater than unity

Description : n vibration isolation system, if ω/ω n is less than √2 , then for all values of the damping factor, the transmissibility will be a) less than unity b) equal to unity c) greater than unity d) zero

Last Answer : c) greater than unity

Description : Critical speed of shaft and disc system A) Is equal to natural frequency of the system in transverse vibration B) Is equal to natural frequency of the system in torsional vibration C) Is ... of the system in longitudinal vibration D) Bears no relationship to any of the system natural frequency

Last Answer : A) Is equal to natural frequency of the system in transverse vibration

Description : The rotating shaft or rotor vibrates with excessive lateral vibration at angular speed at which occurs is called as A) rotating speed B) critical speed C) vibrating speed D) None of the above

Last Answer : B) critical speed

Description : The resistance to the motion of the body is provided by ______ a) Medium of vibration b) Speed of vibration c) Length of the material d) External friction

Last Answer : a) Medium of vibration

Description : . In centrifugal pendulum absorber , the natural frequency in cycle per second can be given by A Fn =N √(R/L) B Fn =1/N √(R/L) C Fn =N/2 √(R/L) D Fn =N2 √(R/L)

Last Answer : A Fn =N √(R/L)

Description : In centrifugal pendulum absorber , the natural frequency in cycle per second can be given by A) Fn =N √(R/L) B) Fn =1/N √(R/L) C) Fn =N/2 √(R/L) D) Fn =N2 √(R/L)

Last Answer : A) Fn =N √(R/L)

Description : In damped vibrations, the amplitude of the resulting vibration gradually reduces. This is due to the reason that an amount of energy is always dissipated to overcome the ________ * 1 point (A) Frictional resistance (B) Work done(C) Fluid pressure (D) Air pressure

Last Answer : (A) Frictional resistance

Description : The vibration in a vehicle is normally expressed in the terms of the ______________. (A) displacement (B) velocity (C) acceleration (D) none of the above

Last Answer : (C) acceleration

Description : In a two-rotor system, torsional vibration occurs only if the rotors are moving in the ______ direction. (A) same (B) opposite (C) either same or opposite (D) none of the above

Last Answer : (B) opposite

Description : The accelerometers are commonly used in vibration measurement due to their ___________. (A) small size and low sensitivity (B) the large size and high sensitivity (C) the large size and low sensitivity (D) small size and high sensitivity

Last Answer : (D) small size and high sensitivity

Description : Which of the following systems produce a vibration in the foundation? (A) Coupled machine(B) Uncoupled machine (C) Balanced machine (D) Unbalanced machine

Last Answer : (D) Unbalanced machine

Description : From the following, which one is a type of vibration measuring instrument? A Mechanical B Electrical C Magnetic D All of the above

Last Answer : D All of the above

Description : In vibration isolation system, if ω/ωn, then the phase difference between the transmitted force and the disturbing force is A 0° B 90° C 180° D 270°

Last Answer : C 180°

Description : The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that A Its natural frequency is very low in comparison to the frequency ... is equal to the frequency of vibration D Measurement of vibratory motion is without any reference point

Last Answer : C Its natural frequency is equal to the frequency of vibration

Description : The ratio of the maximum displacement of the forced vibration to the deflection due to the static force, is known as A Damping factor B Damping coefficient C Logarithmic decrement D Magnification factor

Last Answer : D Magnification factor

Description : When there is a reduction in amplitude over every cycle of vibration, then the body is said to have A Free vibration B Forced vibration C Damped vibration D None of the mentioned

Last Answer : C Damped vibration

Description : Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. A 25.62 rad/sec B 20.78 rad/sec C 14.4 rad/sec D 15.33 rad/sec

Last Answer : A 25.62 rad/sec

Description : Which of the following is a type of free vibration? A Longitudinal vibrations B Transverse vibrations C Torsional vibrations D A, B and C

Last Answer : D A, B and C

Description : The number of cycles described in one second is known as _______. A period of vibration B cycle C frequency D all of the above

Last Answer : C frequency

Description : The motion completed during one time period is known as _______. A period of vibration B cycle C frequency D all of the above

Last Answer : B cycle

Description : In a two-rotor system, torsional vibration occurs only if the rotors are moving in the ______ direction. A. same B. opposite C. either same or opposite D. none of the above

Last Answer : B. opposite

Description : The motion of a system executing harmonic motion with one natural frequency is known as _______ A. principal mode of vibration B. natural mode of vibration C. both a. and b. D. none of the above

Last Answer : C. both a. and b.

Description : In the diagram shown below, if rotor X and rotor Z rotate in same direction and rotor Y rotates in opposite direction, then specify the type of node vibration. A. Three node vibration B. Two node vibration C. Single node vibration D. None of the above

Last Answer : B. Two node vibration

Description : Calculate natural frequency of damped vibration, if damping factor is 0.52 and natural frequency of the system is 30 rad/sec which consists of machine supported on springs and dashpots. A 21 rad/sec B 25.62 rad/sec C 20.22 Hz D 3.15 Hz

Last Answer : B 25.62 rad/sec

Description : During resonance A the Vibrations remains unaffected B no vibration occurs C low amplitude of vibration occurs D high amplitude of vibration occurs

Last Answer : D high amplitude of vibration occurs

Description : The ratio of the maximum displacement of the forced vibration to the deflection due to the static force is known as A Logarithmic decrement B Magnification factor C Damping factor D None of the mentioned

Last Answer : B Magnification factor

Description : In coulomb damping the frequency of damped vibrations is A Equal to that of undamped vibrations B Less than that of undamped vibrationsC More than that of undamped vibrations D Independent of the frequency of undamped vibration

Last Answer : A Equal to that of undamped vibrations

Description : Natural frequency of the system is due to A Resonance B Forced Vibration C Damping D Free Vibration

Last Answer : D Free Vibration

Description : Increasing which of the following factor would result in increase of free torsional vibration? A. Radius of gyration B. Mass moment of inertia C. Polar moment of inertia D. Length

Last Answer : C. Polar moment of inertia

Description : In vibration isolation system, if ω/ω n > 1, then the phase difference between the transmitted force and the disturbing force is A. 0° B. 90° C. 180° D. 270°

Last Answer : C. 180°

Description : In vibration isolation system, the transmissibility will be equal to unity, for all values of damping factor, if ω/ωn is A. Equal to 1 B. Equal to √2 C. Less than √2 D. Greater than √2

Last Answer : B. Equal to √2

Description : In the diagram shown below, if rotor X and rotor Z rotate in same direction and rotor Y rotates in opposite direction, then specify the type of node vibration. A. Three node vibration B. Two node vibration C. Single node vibration D. None of the above

Last Answer : B. Two node vibration

Description : An increase in the mass moment of inertia results in ________ in vibration frequency. A. increase B. decrease C. unchanged D. none of the above

Last Answer : B. decrease