State classification of Phase controlled rectifiers.

State classification of Phase controlled rectifiers.
by

1 Answer

Answer :

Classification of phase controlled rectifiers:

image

by

Related questions

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

Single-phase mid-point controlled rectifier with RL load

Description : Single-phase mid-point controlled rectifier with RL load

Last Answer : Single-phase mid-point controlled rectifier with RL load : The circuit configuration of single-phase midpoint controlled rectifier is shown in the figure. During positive half-cycle of ... some part of next positive half-cycle of voltage with reversed polarity can appear across load.

Single-phase Midpoint controlled rectifier with Resistive load

Description : Single-phase Midpoint controlled rectifier with Resistive load

Last Answer : Single-phase Midpoint controlled rectifier with Resistive load:  1) During positive half cycle of AC supply, a is positive with respect to b , this makes T1 forward biased and T2 is reverse ... voltage reverses the polarity and T2 is turned off. The operation is as shown in waveforms.

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms

Description : A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

Last Answer : Please show the solution for this question

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a

Description : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is

Last Answer : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is √3/2

Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Description : Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Last Answer : Single phase fully controlled half wave converter:  The circuit diagram of single-phase half-wave controlled rectifier with RL load and without freewheeling diode is shown in Fig. (a). The SCR T is ... , when again pulse is applied, the SCR is turned on & the above cycle is repeated. 

is igbt current controlled device ?

Last Answer : No, IGBT is not the current controlled device. IGBT is a voltage controlled device. IGBT have combine qualities of MOSFET and BJT. The high switching speed of MOSFET and low conduction losses of BJT. Also, IGBT which stands for Insulated Gate Bipolar Transistor have high input impedance.

why mosfet is voltage controlled device?

Last Answer : already answered here is mosfet current controlled device?

State the classification of transmission lines depending on length of transmission lines.

Description : State the classification of transmission lines depending on length of transmission lines. 

Last Answer : A) According to Voltage level: ( 2 Marks)  a) High voltage Transmission Line (HV) up to 33 KV  b) Extra High Voltage Transmission Line (EHV) above 33 KV up to 400 KV  c) Ultra ... Transmission Line: - The length of Long transmission Line is above 200KM and its line voltage is above 100KV

State the classification of distribution substation.

Description : State the classification of distribution substation. 

Last Answer : The classification of distribution substation. 1. Pole mounted distribution substation 2. Plinth mounted distribution substation 3. Compact/prefabricated distribution substation 4. ... Indoor distribution substation 6. Outdoor distribution substation 7. Mobile distribution substation 

Give the classification of the errors used in measuring instrument & state the reason for their occurrence.

Description : Give the classification of the errors used in measuring instrument & state the reason for their occurrence.

Last Answer : Types of errors in measuring instruments:  A) Gross error: These are due to mistakes on the part of person using the instrument.  B) Systematic Error:  i) Instrumental Error: These ... multiplying factor.  C) Random error: These persist even after gross and systematic errors are removed. 

List classification of distributor system with their advantages each.

Description : List classification of distributor system with their advantages each.

Last Answer : According to scheme of connection there are three types of distribution systems: - 1.Radial (Tree) distribution system 2.Ring mains (Loop) distribution system 3. Grid (interconnected) ... It has highest reliability to maintain supply even when there was maintenance on any one feeder.

the classification of cables. (i) According with voltage levels. (ii) According to numbers of core.

Description : the classification of cables. (i) According with voltage levels. (ii) According to numbers of core.  

Last Answer : 1. Classification of cables with their voltage levels: 1. Low voltage (tension) cable/LT cable: for operating voltage 1.1 KV. 2. High voltage (tension) cable/HT cable: for operating voltage 11 KV. 3. Super ... 4. Three & half core cable. 5. Four core cable 6. Six core cable 7. Multi core cable

Define Electrical Installation and give its classification.

Description : Define Electrical Installation and give its classification.

Last Answer : Meaning of Electrical installation : Electrical installation is a process of estimation and erection of electrical wiring with materials, and electrical machines used by ... Residential Electrical Installation ii) Commercial Electrical Installation iii) Industrial Electrical Installation 

Give classification of resistance based on their ranges.

Description : Give classification of resistance based on their ranges.

Last Answer : Classification of Resistances Based on Their Ranges: 1) Low resistance: less than 1 ohm. 2) Medium resistance: 1 ohm to 0.1 Mega ohms. 3) High resistance: greater than 0.1 Mega ohms.

The speed of a three-phase induction motor is controlled by variable voltage variable frequency control

Description : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque  (1) Decreases (2) Increases (3) Remains constant (4) None of the above

Last Answer : The speed of a three-phase induction motor is controlled by variable voltage variable frequency control (i.e. keeping V/f constant). As the frequency is reduced, the slip at maximum torque Increases 

Application one lamp controlled from two places

Description : Application one lamp controlled from two places

Last Answer : Application one lamp controlled from two places: 1. For Stair case wiring 2. Hospital Wiring ( For operating the lamp in room and nursing station) 3. Bedroom Lighting. 

How are nuclear reactors controlled? Explain two different methods in brief.

Description : How are nuclear reactors controlled? Explain two different methods in brief.

Last Answer : Nuclear reactor is controlled using control rods: Control rods are made up of very high neutron absorbing material like boron, cadmium. By adjusting height of control rods on reactor core ... of nuclear reaction will increase. Whereas by pushing control rod towards the core it will reduce.

A current controlled voltage source is equivalent to :

Description : A current controlled voltage source is equivalent to :  (A) series voltage feed -back amplifier (B) shunt current feed -back amplifier (C) shunt voltage feed -back amplifier (D) series current feed -back amplifier

Last Answer : A current controlled voltage source is equivalent to : shunt voltage feed -back amplifier

In voltage source converter based HVDC transmission system the active power is controlled by changing

Description : In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

Last Answer : In voltage source converter based HVDC transmission system the active power is controlled by changing phase angle of the converter ac input voltage

For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is

Description : For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is

Last Answer : For a 15-bus power system with 3 voltage controlled buses, the size of Jacobian matrix is 25 x 25

The speed of a locomotive is controlled by?

Last Answer : The speed of a locomotive is controlled by gear box.

The gravity controlled instrument has crowded scale because current is proportional to?

Last Answer : The gravity controlled instrument has crowded scale because current is proportional to sine of deflection angle.

MOSFET are current controlled or voltage controlled devices?

Last Answer : MOSFET  are voltage controlled devices.

Is BJT current controlled or voltage controlled?

Last Answer : BJT is current controlled device.

why thyristor is called semi controlled device?

Last Answer : Thyristor can only be turned on by small gate pulse but it cannot be turn off by using gate hence thyristor is called semi controlled device.

why bjt is called current controlled device?

Last Answer : In  BJT  there  is  movement  of   electrons  and  holes   accros  the  junctions  which  is  basicaly  current  flow.

is bjt a voltage controlled device ?

Last Answer : No, BJT is a current controlled device .

Chopper controlled DC motor

Description : Chopper controlled DC motor

Last Answer : Chopper controlled DC motor

Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it.

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

Oscillator independent of phase shift is

Description : Oscillator independent of phase shift is  (1) Relaxation (2) Wein bridge (3) Clapp (4) All of these

Last Answer : Oscillator independent of phase shift is Relaxation 

Explain three phase half wave controller or three phase unidirectional controller.

Description : Explain three phase half wave controller or three phase unidirectional controller.

Last Answer : Three phase half wave controller or unidirectional controller:

Explain Three Phase Bidirectional Delta Connected Controller.

Description : Explain Three Phase Bidirectional Delta Connected Controller.

Last Answer : Three Phase Bidirectional Delta Connected Controller:

Explain three phase bridge inverter.

Description : Explain three phase bridge inverter.

Last Answer : Three phase bridge inverter: Three phase bridge inverter converts DC voltage input to three-phase variable frequency variable voltage output. DC voltage source can be a DC source or output of the rectifier. ... in proper sequence. The switch may be thyristor or IGBT etc.

Explain the principle of ON OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

Description : Explain the principle of ON-OFF control and phase control of AC voltage controller with suitable circuit and waveforms.

Last Answer : The integral cycle control (on-off control) and phase angle control are the two types of AC voltage controller. The principle of ON-OFF control: The on-off control is also called an integral cycle ... control. In phase control, the switch is on for some period of each cycle.  

Explain three phase full wave controller.

Description : Explain three phase full wave controller.

Last Answer : Three phase full wave controller: Three phase full wave controller is also called as the three-phase bidirectional controller. Let the load is star connected so at each phase there are antiparallel connected SCRs. ... conduct at the same time and the third phase will be open.

three phase to single phase cycloconverter

Description : three phase to single phase cycloconverter

Last Answer : three phase to single phase cycloconverter

single phase full converter

Description : single phase full converter

Last Answer : single phase full converter

what is TCSC?

Description : what is TCSC?

Last Answer : Thyristor Controlled Series Capacitor (TCSC)

A freewheeling diode in phase -controlled rectifiers

Description : A freewheeling diode in phase -controlled rectifiers  (a) enables inverter operation (b) is responsible for additional reactive power (c) improves the line power factor (d) is responsible for additional harmonics

Last Answer : A freewheeling diode in phase -controlled rectifiers improves the line power factor

State suitable single phase motor for following applications: (i) Table fan (ii) Mixers and Grinders

Description : State suitable single phase motor for following applications: (i) Table fan (ii) Mixers and Grinders

Last Answer : Application Suitable Single Phase Motor Table Fan 1) Capacitor split phase motor 2) Capacitor start capacitor run motor Mixers and Grinders 1) Universal motor 2) A.C. Series motor

State any four advantages of three phase induction motor.

Description : State any four advantages of three phase induction motor. 

Last Answer : Advantages of three phase induction motor https://youtu.be/27OIOCKN05U

State the use of:- (i) Clip-on-ammeter (ii) Phase sequence indicator

Description : State the use of:- (i) Clip-on-ammeter (ii) Phase sequence indicator

Last Answer : (i) Clip-on-ammeter: used for measurement of current in cables/lines in live conditions without disconnecting them.  (ii) Phase sequence indicator: To determine /find the phase sequence of 3 phase supply. 

State the meaning of creeping error in 1 phase energy meter.

Description : State the meaning of creeping error in 1 phase energy meter.

Last Answer : Creeping error: It is defined as the slow and continuous rotation of the disc of the energy-meter when only pressure coil is energized with no current in the current coil (load current = 0). ... magnet on this iron wire is sufficient to prevent continues rotation of the disc on no load condition.

State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Description : State any two disadvantages of one wattmeter method of measurement of 3 phase power.

Last Answer : State any two disadvantages of one wattmeter method of measurement of 3 phase power. Disadvantages of one wattmeter method:- 1. Only used for balanced load 2. It can not be used for ... connection then neutral point must be available 4. Delta connection must be opened to connect current coil.

State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

Description : State the application of phase sequence indicator; clip on ammeter, frequency meter & P.F. meter.

Last Answer : Phase Sequence Indicator:  1. For finding correct phase sequence of supply  2. For obtaining exact instant of parallel operation of alternators.  3. For obtaining reversal of rotation ...  4. In electroplating industries   5. In various processes industries for measuring power factor

State any four application of three phase circuit.

Description : State any four applications of three phase circuits.

Last Answer : The application of three phase circuits are 1. Three phase circuit is used for power transmission over long distances. 2. Three phase circuit can produce rotating magnetic field 3. Three phase ... three phase Motors and Transformers. 4. Three phase circuit is used for power converters circuits.

State advantages of three phase over single phase.

Description : State advantages of three phase over single phase.

Last Answer : Advantages of 3-phase system over 1-phase system: -  1. More output: For the same size, output of poly-phase machines is always higher than single phase machines.  2. Smaller size: For ... are self- starting: The three phase ac motors are self starting, while single phase induction motor are not.

SINGLE PHASE INDUCTION MOTORS MCQ

Description : SINGLE PHASE INDUCTION MOTORS MCQ

Last Answer : 101. After the starting winding of a single phase induction motor is disconnected from supply, it continues to run only on (a) running winding (b) rotor winding (c) field winding (d) compensating winding Ans: a ... motor is usually reduced by using (a) gearing (b) belts (c) brakes (d) chains Ans: a