Draw circuit diagram of symmetrical configuration of bridge converter.

Draw circuit diagram of symmetrical configuration of bridge converter.
by

1 Answer

Answer :

image

circuit diagram of symmetrical configuration of bridge converter

by

Related questions

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc

Description : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is (A) 4.5 V (B) 6.75 V (C) 9 V (D) 13.5 V

Last Answer : A 230 V, 50 Hz phase controlled single-phase full-controlled SCR bridge converter draws 15 A constant dc current. If the source inductance is 3 mH, the drop in dc output voltage is 9 V

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load,

Description : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses

Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

Explain full bridge converter.

Description : Explain the operation of full bridge converters with their different operating modes. State its advantages and disadvantages.

Last Answer : Full bridge converter: Full bridge converter provides isolation between input and output. Full bridge converter is used for step up or step down the input voltage. Full bridge converter consists of four power semiconductor ... Require filter on both input and output.

The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole)

Description : The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole)  (A) has q -axis current only (B) has d -axis current only (C) has both d and q axis currents (D) cannot be divided between q and d axis currents

Last Answer : The armature current on symmetrical 3 phase short circuit of a synchronous machine (salient pole) has d -axis current only

The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a

Description : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ (A) directly proportional to α and Φ (B) ... proportional to α and inversely proportional to Φ (D) directly proportional to Φ and inversely proportional to α

Last Answer : The no-load speed of a single-phase SCR bridge converter fed separately excited dc motor operating at a firing delay angle, α and flux, Φ directly proportional to α and inversely proportional to Φ

Draw the circuit diagram of battery charger using SCR and explain it’s working.

Description : Draw the circuit diagram of battery charger using SCR and explain it’s working.

Last Answer : Battery charger circuit using SCR: The figure shows the battery charger circuit using SCR. A 12V discharged battery is connected in the circuit and switch SW is closed. The singlephase 230V ... not fired. In this way, after full charging, further charging is automatically stopped.

Draw circuit diagram of Class B commutation.

Description : Draw circuit diagram of Class B commutation.

Last Answer : Class B: Resonant Pulse Commutation:

explain blanking times for Bridge circuit?

Description : explain blanking times for Bridge circuit?

Last Answer : Blanking time is provided by driver circuit to power switch. Blanking time is important because the turn on input of one transistor must be delayed with turn off input of another transistor if both ... are connected in one converter leg. This blanking time helps in avoiding cross conduction.

Explain working of AC circuit breaker using SCR with circuit diagram.

Description : Explain working of AC circuit breaker using SCR with circuit diagram.

Last Answer : AC Circuit Breaker:  The circuit configuration of static AC circuit breaker using SCR is shown in the figure. When switch S' is closed, the SCRs T1 and T2 are fired in positive ... to non-availability of gate current. Thus the maximum time delay for breaking the circuit is one half-cycle.

In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR

Description : In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in (A) voltage notching (B) harmonic distortion (C) voltage sag (D) voltage swell

Last Answer : In a 3-phase converter circuit during commutation when one SCR in one phase is turned on to turn-off an SCR in another phase, results in voltage notching

Define Multivibrator. State the types of multivibrator. Which M/V can be used as a flip-flop? Draw the circuit diagram.

Description : Define Multivibrator. State the types of multivibrator. Which M/V can be used as a flip-flop? Draw the circuit diagram.

Last Answer : Definition:- A multivibrator is an electronic circuit that switches rapidly by means of positive feedback between two or more states.  OR  A multivibrator is an electronic circuit used to implement a ... Bistable Multivibrator: it can operate as a flip-flop, Circuit diagram 

Draw the circuit diagram of crystal oscillator and explain its working.

Description : Draw the circuit diagram of crystal oscillator and explain its working.

Last Answer : To excite a crystal for operation in the series-resonant mode it may be connected as a series element in a feedback path, the crystal impedance is the smallest and the amount of positive feedback is the largest. ... which is good.  The resonant frequency is given as  Fo = 1/( 2 π √LC ) 

Draw and explain Hartley Oscillator circuit diagram.

Description : Draw and explain Hartley Oscillator circuit diagram.

Last Answer : Function of each component: 1. An NPN transistor connected in a common emitter configuration works as the active device in amplifier stage and CE configuration provides 180°phase shift. 2. R1 and R2 ... circuit to the base-emitter circuit.  The frequency of oscillation is given as-  

Draw full bridge & half bridge configuration with common cathode.

Description : Draw full bridge & half bridge configuration with common cathode.

Last Answer : Half Bridge Configuration: Full Bridge Configuration: 

A dummy strain gage is used in a quarter bridge strain gage circuit to :

Description : A dummy strain gage is used in a quarter bridge strain gage circuit to :  (A) compensate for changes in temperature and lead wire resistance  (B) produce more output voltage from the bridge  (C) increase the sensitivity of the bridge  (D) compensate lead wire resistance only

Last Answer : A dummy strain gage is used in a quarter bridge strain gage circuit to : compensate for changes in temperature and lead wire resistance 

Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Description : Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Last Answer : Single phase fully controlled half wave converter:  The circuit diagram of single-phase half-wave controlled rectifier with RL load and without freewheeling diode is shown in Fig. (a). The SCR T is ... , when again pulse is applied, the SCR is turned on & the above cycle is repeated. 

Describe the working principle of Thyristor operated dimmer with the help of circuit diagram.

Description : Describe the working principle of Thyristor operated dimmer with the help of circuit diagram.

Last Answer : Thyristor operated dimmer: A popular thyristor operated dimmer circuit employ TRIAC-DIAC phase control for low AC power control. During each half-cycle, the capacitor charges through (R1+VR1). When the ... time constant {C (R1+VR1)}. Thus by reducing VR1 the lamp brightness can be increased.

Give the effect of source impedance on converter operation.

Description : Give the effect of source impedance on converter operation.

Last Answer : Effect of source impedance on converter operation: For single-phase fully controlled bridge converter, the SCRs are triggered in pairs alternately. During positive half-cycle of input, SCRs T1 and T2 are triggered ... increases and as a consequence, the output dc voltage decreases. 

The percent resolution of an 8 -bit D/A converter is

Description : The percent resolution of an 8 -bit D/A converter is

Last Answer : The percent resolution of an 8 -bit D/A converter is 0.392

A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms

Description : A 3 -phase, fully controlled, converter is feeding power into a DC load at a constant current of 150 A, the rms value of the current flowing through each thyristor of the converter is

Last Answer : Please show the solution for this question

Why the power factor of semiconverter is better than full converter?

Description : Why the power factor of semiconverter is better than full converter?

Last Answer : Power factor of semiconverter is better than full converter

Explain buck converter.

Description : Explain buck or step down converter and draw its waveforms.

Last Answer : Buck converter or Step down converter: Buck converter is a step-down converter. The buck converter step-down the output voltage and step up the output current. Buck converter is a DC to DC converter. ... load. The output voltage is controlled by controlling on period and off period.

single phase full converter

Description : single phase full converter

Last Answer : single phase full converter

Explain flyback converter.

Description : Explain flyback converter and draw its waveforms.

Last Answer : Flyback converter: A flyback converter is used for getting DC output and for isolating input mains and output voltage. A flyback converter is like a buck-boost converter with input and output isolated. There ... during the off time transformer transfer the energy to load.

Explain buck boost converter.

Description : Explain buck boost converter and draw its waveforms.

Last Answer : Buck-Boost converter: The buck-boost converter consists of a transistor for switching purpose, diode, inductor, and capacitor. Buck-boost converter is the combination of the buck converter and boost ... In buck-boost converter both input current and diode current are discontinuous.

what is Cuk converter?

Description : what is Cuk converter and draw its waveforms.

Last Answer : Cuk converter: Cuk converter is the series combination of boost and the buck converter. The Cuk converter is the DC to DC converter whose output voltage is greater than or less the than the input ... controlling the switch duty cycle the output voltage can be controlled.

Explain three phase bridge inverter.

Description : Explain three phase bridge inverter.

Last Answer : Three phase bridge inverter: Three phase bridge inverter converts DC voltage input to three-phase variable frequency variable voltage output. DC voltage source can be a DC source or output of the rectifier. ... in proper sequence. The switch may be thyristor or IGBT etc.

Explain MOSFET gate drive circuit and totem pole configuration.

Description : Explain MOSFET gate drive circuit and totem pole configuration.

Last Answer : MOSFET gate drive circuit: The turning on and turning off of MOSFET can be controlled from gate to source voltage signal. If the gate to source voltage of MOSFET exceeds threshold ... this configuration, the two switches (transistors) are used in totem pole arrangement with a comparator.

How to Build a Static 3 Phase Converter

Description : How to Build a Static 3 Phase Converter

Last Answer : How to Build a Static 3 Phase Converter Static 3 phase converters enable offices and residents to conserve energy efficiently. In fact, electricity is available in 3 power phases, which enables ... converter and the necessary appliances that are needed in building the main and the remote appliances.

In voltage source converter based HVDC transmission system the active power is controlled by changing

Description : In voltage source converter based HVDC transmission system the active power is controlled by changing (A) phase angle of the converter ac input voltage (B) supply frequency of the converter ac input voltage (C) magnitude of the converter ac input voltage (D) DC voltage at the inverter terminals

Last Answer : In voltage source converter based HVDC transmission system the active power is controlled by changing phase angle of the converter ac input voltage

A rotory converter can also be run as a?

Last Answer : A rotory converter can also be run as a synchronous motor.

What is Analog to Digital Converter (ADC) ?

Description : What is Analog to Digital Converter (ADC) ?

Last Answer : Analog to Digital Converter (ADC)  Analog quantity may be voltage, temperature, sound, speed, audio etc. it is information or signal. ... digital form), digital speedometer (converts analog speed into digital form) etc.

Digital to Analog Converter (DAC)

Description : Digital to Analog Converter (DAC)

Last Answer : Digital to Analog Converter (DAC) Digital means binary (1 0) and 1 and 0 may be true and false or on and off or high and low. Analog means continuous signal or information ... wave. Phase Shift Keying (PSK) is transmit digital data by changing the phase of carrier wave.

With neat diagram explain synchronized UJT triggering circuit.

Description : With neat diagram explain synchronized UJT triggering circuit.

Last Answer : Line Synchronized UJT triggering circuit: The UJT is almost ideal as a firing device for SCRs. There are 2 main reasons for the compatibility between UJTs and SCRs. Firstly, the UJT produces a ... , the SCR is sure to have the right polarity between the anode and cathode for turning on.

Draw the labeled block diagram of process control system and explain each block.

Description : Draw the labeled block diagram of process control system and explain each block.

Last Answer : Explanation - Process control system consists of process or plant, sensor, error detector, automatic Controller, actuator or control element. 1) Process or plant- process means some manufacturing sequence ... process which changes the process variable. Output of this block is denoted by u .

Draw the block diagram of PLC.

Description : Draw the block diagram of PLC.

Last Answer : Block diagram of PLC and input/output devices used for PLC Input/output devices - The input module has bank of terminals for physically connecting input devices, like push buttons, limit switches etc. ... is to translate signals from the PLC's CPU into a form that the output device can use.

Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Description : Draw block diagram of PLL as a FM demodulator. Explain function of each block.

Last Answer : Operation:  The FM signal which is to be demodulated is applied at the input of the PLL.  the PLL is locked to the FM  The error voltage produced at ... using PLL ensures a high Linearity, between the instantaneous input frequency and VCO control voltage (error amplifier output)

Draw block diagram for CNC drilling machine and explain its working.

Description : Draw block diagram for CNC drilling machine and explain its working.

Last Answer : Block diagram consist of the following points:  Machine tool with DC servo motor as feedback element. The transducer is added as adaptive control application.  The auxiliary controller ... line.  The interrupt pulses are generated by TBG and supplied to computer through inter

Draw the block diagram of satellite sub-system and explain power subsystem.

Description : Draw the block diagram of satellite sub-system and explain power subsystem.

Last Answer : POWER SUBSYSTEM- This system provides the necessary DC power to the satellite. All communication satellites derive their electrical power from solar cells. There is also a battery backup facility used during ... . to d.c. converter is used to raise the level of low voltages to high voltage.

Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter.

Description : Draw the wiring diagram of fluorescent tube. Explain the working of choke and starter. 

Last Answer : Fluorescent lamp:- Operation:- When switch is ON current flows through the choke-filament no1- starter-filament no. 2- to neutral, At that time choke induces high voltage which is applied to ... at the time of starting. ii) Starter: To make and break the circuit to start the tube. 

Draw the labeled interfacing diagram to interface relay with 89C51 microcontroller.

Description : Draw the labeled interfacing diagram to interface relay with 89C51 microcontroller.

Last Answer : the labeled interfacing diagram to interface relay with 89C51 microcontroller

Draw block diagram of instrumentation system. State function.

Description : Draw block diagram of instrumentation system. State function.

Last Answer : Primary transducer: The sensor which comes in contact with the measurement medium to sense the quantity. Variable conversion element: the transducer which converts the sensor ... transmitted through suitable transmission medium to the operator or presented with the help of indicators.

Draw the block diagram of basic wind energy conversion system and write function of each block.

Description : Draw the block diagram of basic wind energy conversion system and write function of each block. 

Last Answer : Block diagram of basic wind energy conversion system: OR Components of wind power plant and their functions:  1) Rotor /Blade/Aero-turbine: Blade extracts significant power from the ... stronger and smoother. Towers are supports to raise the main part of the turbine up in the air.

Draw a block diagram of electronic energy meter. Write function of each block.

Description : Draw a block diagram of electronic energy meter. Write function of each block.

Last Answer : Electronic Energymeter  Functions of components/blocks: - CT reduces current to reasonable value for current scaling network. - Voltage & current scaling networks reduce proportionally the voltage ... ADC converts the square wave frequency analog output to display the energy in watthour.

Draw block diagram of CRO. Write function of each block.

Description : Draw block diagram of CRO. Write function of each block.

Last Answer : 1. Vertical amplifier strengthens the input signal applied to vertical depleting plates 2. Trigger circuit gives input to time base circuit 3. The output of time base generator is amplified by ... of CRT internally coated with Phosphors material on which we observe waveform of the input signal.

How to Build a Bridge

Description : How to Build a Bridge

Last Answer : How to Build a Bridge How to Build a Bridge Building a bridge is not an every day task, you do not see bridges going up overnight and it takes a skilled engineer to master this craft. Bridges ... this can be one of the most satisfying moments of your life to know that you have achieved your goal.

How to Become a Bridge Inspector

Description : How to Become a Bridge Inspector

Last Answer : How to Become a Bridge Inspector Bridge Inspectors are construction professionals who are well versed in a number of building disciplines. Among the talents of a bridge inspector are such ... secure employment in a variety of different settings, both in government agencies and private business.

How to Become a Bridge Engineer

Description : How to Become a Bridge Engineer

Last Answer : How to Become a Bridge Engineer Bridge Engineers are construction professionals that bear a major part of the responsibility for the safety and stability of bridges. Consequently, a bridge engineer ... new business. A well-established reputation is vital to the success of bridge engineering career.