State important specification parameters of ADC

State important specification parameters of ADC
by

1 Answer

Answer :

Accuracy

Resolution

Linearity

Conversion time

Settling time

stability
by

Related questions

List various elements of mechatronic system and state applications.

Description : List various elements of mechatronic system and state applications.

Last Answer : Elements Sensors. Actuators (Hydraulics, Phnumetics) PLC, Micro controllers. Electrical Motors. Mechanical Couplings, Assembly & Gears. Control Panel. Applications ... washer and washing machines. automatic air conditioning systems unmanned aerial vehicles and automatic pilots. 

Define transducer. State factors which are considered while selecting transducer for a particular application.

Description : Define transducer. State factors which are considered while selecting transducer for a particular application.

Last Answer : Transducer - It converts one form of signal into another form. A transducer is a device that is used to convert a physical quantity into its corresponding electrical signal. ... compatibility : The transducer should maintain input and output characteristic for the selected environmental condition.

State the need of multistage amplifier. List the types of multistage amplifier and give two advantages of each type.

Description : State the need of multistage amplifier. List the types of multistage amplifier and give two advantages of each type. 

Last Answer : Need of multistage amplifier: The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, ... use more than one stage of amplification. Such an amplifier is called a MULTISTAGE AMPLIFIER .

Draw a labelled pin diagram of IC-555 and state function of each pin

Description : Draw a labelled pin diagram of IC-555 and state function of each pin

Last Answer : Pin Name Purpose 1 GND Ground reference voltage, low level (0 V)  2 TRIG The OUT pin goes high and a timing interval starts when this input falls below 1/2 of ... 8 Vcc Positive supply voltage, which is usually between 3 and 15 V depending on the variation.

Define counter. State four applications of counter.

Description : Define counter. State four applications of counter.

Last Answer : Counter - The circuit which counts number of clock pulses is called as counter. Applications - Processor Real time clock Calculator Batch counter

Draw symbol of NPN transistor and state three configurations of transistor (BJT)

Description : Draw symbol of NPN transistor and state three configurations of transistor (BJT)

Last Answer : Configuration - Common Emitter Common Collector Common Base

Give the speciality of zener diode. State its 2-3 applications

Description : Give the speciality of zener diode. State its 2-3 applications

Last Answer : Speciality - This diode can keep breakdown voltage constant across it. It is used in reverse bias. Applications - Zener diodes voltage regulation as reference elements surge suppressors switching applications clipper circuits.

State the advantages of dual slope ADC

Description : State the advantages of dual slope ADC

Last Answer :  It provides excellent noise rejection of ac signals whose periods are integral multiples of the integration time T. It is defined as the total time required to convert an analog signal into its ... output. It depends on the conversion technique used & the propagation delay of circuit components.

State features of ADC 0808.

Description : State features of ADC 0808.

Last Answer : 1. Easy to interface with all Microprocessors or works Stand alone. 2. Eight channel 8-bit ADC module. 3. Can measure up to 8 Analog values. 4. On chip Clock not available, external Oscillator ... (Clock). 5. Digital output various from 0 to 255, operating power is 15mW, conversion time 100us.

Comparison of three configuration of BJT

Description : Comparison of three configuration of BJT

Last Answer : Parameter Common Base(CB) Common Emitter (CE) Common collector (CC) Input terminal  Emitter Base Base Common terminal Base Emitter Collector Output terminal Collector Collector Emitter Gain factor Alpha(Ic/Ie) Beta(Ic/Ib) Gamma(Ie/Ib)

Piezo-electric effect

Description : Piezo-electric effect

Last Answer : Piezoelectric Effect is the ability of certain materials to generate an electric charge in response to applied mechanical stress. The word Piezoelectric is derived from the Greek piezein, which means to squeeze or ... Storage Temperature Range: -55 to + 125°C Insulation Resistance: 500 M ohms

Shift Register

Description : Shift Register

Last Answer : Shift Register:- Shift Register is a group of flipflops used to shift data from one side to other side or to convert serial data into parallel or vice versa. Shift registers are of following types  i) ... iii) Parallel in serial out(PISO) iv) Parallel in parallel out(PIPO)

Comparison of BJT and FET

Description : Comparison of BJT and FET

Last Answer : FET BJT It is unipolar device i.e. current in the device is carried either by electrons or holes It is bipolar device i.e. current in the device is carried either by both ... is comparatively more noisy. It is relatively immune to radiation. It is susceptible to radiation

Selection Criteria of PLC

Description : Selection Criteria of PLC

Last Answer : Selection criteria :- To select PLC for any particular application following points are to be considered. a) Type of PLC: Analog or Digital b) Number of inputs and outputs to PLC c) Operating voltage ... Type of memory of PLC g) Type of programming h) Reliability of PLC i) Flexibility of PLC

Function of OR Gate its logical symbol and truth table.

Description : Function of OR Gate its logical symbol and truth table.

Last Answer : Function: - OR gate is used to perform logical addition. So used in adder subtractor and logic circuits where logical Oring is required. Used to implement SOP form equations. Also used in PLA logic. Logical symbol of OR gate :- Truth table:- 

Define multiplexer. Draw logical symbol of 4:1 multiplexer with truth table and output logical equation

Description : Define multiplexer. Draw logical symbol of 4:1 multiplexer with truth table and output logical equation

Last Answer : Multiplexer - it is a combinational circuit which selects one input from several inputs and connects it to the output.  It is a circuit which has N-input and single output is called as multiplexer.

Compare microprocessor and microcontroller

Description : Compare microprocessor and microcontroller

Last Answer : Application Microprocessor - Computer, Mobile phone, calculator Microcontroller - washing machine, microwave oven Microprocessor Microcontroller Do not have inbuilt RAM or ROM ... access Less multifunction pins on the IC Many multifunction pins on the IC

Draw circuit diagram of two stage RC coupled amplifier using BJT

Description : Draw circuit diagram of two stage RC coupled amplifier using BJT

Last Answer : BJT - To amplify input signal. R1 & R2 = Biasing resistor to provide DC biasing voltage RE = Emitter resistor to control gain RL = Load resistor to carry load current Cin = Cout = Coupling capacitors to block DC CE = emitter bypass resistor

Compare LED and Photo diode

Description : Compare LED and Photo diode 

Last Answer : Parameters LED (Light Emitting Diode) Photodiode Definition Two terminal device which converts electrical energy into light energy.  Two Terminal Device which converts light energy into ... and Numeric display etc. Switching, high speed counting, ac coupled signaling etc.

Name the circuit used in rectifier to minimize ripple. List the types of this circuit with simple circuit diagram.

Description : Name the circuit used in rectifier to minimize ripple. List the types of this circuit with simple circuit diagram.

Last Answer : Rectifier filter is an electronic circuit that removes ripple or unwanted AC signal components from the output of a Rectifier. Types - (a) Series Inductor filter (d) Shunt capacitor filter (b) L-C type filter (e) Π - type filter

Draw simple block diagram of CNC machine and describe in short.

Description : Draw simple block diagram of CNC machine and describe in short.

Last Answer : (i) Input Devices: These are the devices which are used to input the part program in the CNC machine. There are three commonly used input devices and these are punch tape reader, magnetic tape ... Unit: A monitor is used to display the programs, commands and other useful data of CNC machine.

Describe how Op-Amp is used as adder using circuit diagram and output voltage equation.

Description : Describe how Op-Amp is used as adder using circuit diagram and output voltage equation.

Last Answer : Summing Amplifier Circuit In this simple summing amplifier circuit, the output voltage, ( Vout ) now becomes proportional to the sum of the input voltages, V1, V2, V3, etc. Then we can ... to the non-inverting input of the op-amp, it will produce the positive sum of the input voltages.

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

List various types of CNC machine

Description : List various types of CNC machine

Last Answer : • CNC Plasma Cutting Machine. • CNC Laser Cutting Machine. • CNC Milling Machine. • CNC Router Machine. • CNC Lathe Machine.

Give examples of : (i) Electrical transducer (ii) Mechanical Transducer

Description : Give examples of : (i) Electrical transducer (ii) Mechanical Transducer

Last Answer : (i) Electrical transducer Voltage measurement Temperature measurement Strain measurement (ii) Mechanical Transducer Pressure measurement Force measurement Velocity measurement

Draw pin diagram of Op-Amp IC-741.

Description : Draw pin diagram of Op-Amp IC-741.

Last Answer : Pin diagram of Op-Amp IC-741 :

Why NAND and NOR gate are called as universal gate? Draw AND gate using NAND gate only.

Description : Why NAND and NOR gate are called as universal gate? Draw AND gate using NAND gate only. 

Last Answer : Universal gate - All basic gates functionality can be implemented using NAND and NOR gate hence these gates are called as universal gates.  AND gate using NAND gate

What is the most important specification of loudspeakers and microphones? A. Frequency response B. Power density C. Field Strength D. Gain

Description : What is the most important specification of loudspeakers and microphones? A. Frequency response B. Power density C. Field Strength D. Gain

Last Answer : A. Frequency response

Which act’s important specification was the provincial autonomy.

Description : Which act’s important specification was the provincial autonomy.

Last Answer : 1935

What is an Analog-to-Digital Converter (ADC) in Arduino?

Description : What is an Analog-to-Digital Converter (ADC) in Arduino?

Last Answer : An Analog-to-Digital Converter (ADC) in Arduino is a component that converts analog signals, such as temperature or light, into digital signals that can be processed by the microcontroller.

ABC and ADC are two right triangles with common hypotenuse AC. Prove that angle CAD = angle CAB -Maths 9th

Description : ABC and ADC are two right triangles with common hypotenuse AC. Prove that angle CAD = angle CAB -Maths 9th

Last Answer : Given, AC is the common hypotenuse. ∠B = ∠D = 90°. To prove, ∠CAD = ∠CBD Proof: Since, ∠ABC and ∠ADC are 90°. These angles are in the semi circle. Thus, both the triangles are lying in the semi ... D are concyclic. Thus, CD is the chord. ⇒ ∠CAD = ∠CBD (Angles in the same segment of the circle)

ABC and ADC are two right triangles with common hypotenuse AC. Prove that angle CAD = angle CAB -Maths 9th

Description : ABC and ADC are two right triangles with common hypotenuse AC. Prove that angle CAD = angle CAB -Maths 9th

Last Answer : Given, AC is the common hypotenuse. ∠B = ∠D = 90°. To prove, ∠CAD = ∠CBD Proof: Since, ∠ABC and ∠ADC are 90°. These angles are in the semi circle. Thus, both the triangles are lying in the semi ... D are concyclic. Thus, CD is the chord. ⇒ ∠CAD = ∠CBD (Angles in the same segment of the circle)

In the figure, find teh perimeter of the shaded region where. ADC, AEB and BFC are semi-circles on diameters AC, AB and BC respectively. -Maths 10th

Description : In the figure, find teh perimeter of the shaded region where. ADC, AEB and BFC are semi-circles on diameters AC, AB and BC respectively. -Maths 10th

Last Answer : Given: Diameter of semicircle AEB= 2.8 cm RADIUS OF SEMICIRCLE(AEB)= 2.8/2= 1.4 cm Diameter of semicircle BFC=1.4 cm RADIUS OF SEMICIRCLE(BFC)= 1.4/2= 0.7 cm Diameter of semicircle ADC= 2.8+1.4 = ... ; .6 = 13.2 cm Hence, the perimeter of the shaded region is 13.2 cm HOPE THIS WILL HELP YOU...

What is the full form of ADC ?

Description : What is the full form of ADC ?

Last Answer : The full form of ADC is Aeitional Deputy Commissioner.

In the above figure, O is the centre of the circle AB,AD and CD are the chords . If `/_ ADC=130^(@)` then fid `/_ ACB`.

Description : In the above figure, O is the centre of the circle AB,AD and CD are the chords . If `/_ ADC=130^(@)` then fid `/_ ACB`.

Last Answer : In the above figure, O is the centre of the circle AB,AD and CD are the chords . If `/_ ADC=130^(@)` then fid `/_ ACB`.

Which is the fastest ADC and why?

Description : Which is the fastest ADC and why?

Last Answer : Simultaneous type A/D converter(flash type A/D converter) is the fastest because A/D conversion is performed simultaneously through a set of comparators 

What is the main drawback of a dual-slop ADC?

Description : What is the main drawback of a dual-slop ADC?

Last Answer : The dual slope ADC has long conversion time. This is the main drawback of dual slope ADC

Explain in brief the principle of operation of successive Approximation ADC.

Description : Explain in brief the principle of operation of successive Approximation ADC.

Last Answer : The circuit of successive approximation ADC consists of a successive approximation register (SAR), to find the required value of each bit by trial & error.With the arrival of START command, SAR sets the MSB ... /P signal. This O/P is low or High. This process continues until all bits are checked.

A ______ is a combination load balancer and application server that is a server placed between a firewall or router. a) ABC b) ACD c) ADC d) All of the mentioned

Description : A ______ is a combination load balancer and application server that is a server placed between a firewall or router. a) ABC b) ACD c) ADC d) All of the mentioned

Last Answer : ADC

A ______ is a combination load balancer and application server that is a server placed between a firewall or router. a) ABC b) ACD c) ADC d) All of the mentioned

Description : A ______ is a combination load balancer and application server that is a server placed between a firewall or router. a) ABC b) ACD c) ADC d) All of the mentioned

Last Answer : ADC

. A ______ is a combination load balancer and application server that is a server placed between a firewall or router. a) ABC b) ACD c) ADC d) All of the mentioned

Description : . A ______ is a combination load balancer and application server that is a server placed between a firewall or router. a) ABC b) ACD c) ADC d) All of the mentioned

Last Answer : ADC

What is the result if the input of ADC is changing while performing conversion? A

Description : What is the result if the input of ADC is changing while performing conversion? A

Last Answer : Aperture distortion

Resolution of ADC is defined as a) 1/ (2N – 1) b) 2N-1 c) 1/ (2N-1) d) 2N-1

Description : Resolution of ADC is defined as a) 1/ (2N – 1) b) 2N-1 c) 1/ (2N-1) d) 2N-1

Last Answer : b) 2N-1

In ADC 0808 if _______ pin high enables output. a) EOC b) I/P0-I/P7 c) SOC d) OE

Description : In ADC 0808 if _______ pin high enables output. a) EOC b) I/P0-I/P7 c) SOC d) OE

Last Answer : b) I/P0-I/P7

What are the commonest congenitally missing teeth:VERY CONTROVERSIAL BUT SEE THE SAMPLE QUESTIONS FROM ADC IT’S THE ANSWER A. 12, 22 B. 35, 45 ACC TO CAMERON C. 15, 25 D. 33, 43

Description : What are the commonest congenitally missing teeth:VERY CONTROVERSIAL BUT SEE THE SAMPLE QUESTIONS FROM ADC IT’S THE ANSWER A. 12, 22 B. 35, 45 ACC TO CAMERON C. 15, 25 D. 33, 43

Last Answer : A. 12, 22

Which one of the following is true about oral hairy leukoplakia?** ADC M07 A. Associated with HIV virus infection and is commonly seen on the dorsal of the tongue B. Associated with HIV virus infection and is commonly seen on the lateral side of the tongue C. Usually caused by Candida species D. Always associated with trauma to the lateral side of the tongue E. Always associated with pernicious anaemia

Description : Which one of the following is true about oral hairy leukoplakia?** ADC M07 A. Associated with HIV virus infection and is commonly seen on the dorsal of the tongue B. Associated with HIV ... Always associated with trauma to the lateral side of the tongue E. Always associated with pernicious anaemia

Last Answer : B. Associated with HIV virus infection and is commonly seen on the lateral side of the tongue C. Usually caused by Candida species

As far as surgical removal of wisdom teeth is concerned, which of the following is true?**CHECK A. Prophylactic prescription of antibiotic reduces dramatically the chances of infection B. Raising a lingual flap will increases the incidence of neurapraxia but will reduce the incidence of neurotmesis with respect to the lingual nerve ADC M07 C. Prophylactic prescription of dexamethasone will dramatically reduces post operative swelling D. Inferior dental nerve injury is unlikely since the nerve passes medial to the wisdom tooth root E. The use of vasoconstrictors in local anaesthetics will increase the chances of infection.

Description : As far as surgical removal of wisdom teeth is concerned, which of the following is true?**CHECK A. Prophylactic prescription of antibiotic reduces dramatically the chances of infection B. Raising ... root E. The use of vasoconstrictors in local anaesthetics will increase the chances of infection.

Last Answer : C. Prophylactic prescription of dexamethasone will dramatically reduces post operative swelling

Loss of sensation in the lower lip may be produced by,CHECK ADC M07 A. Bell’s palsy B. Traumatic bone cyst C. Trigeminal neuralgia D. Fracture in the mandible first molar region E. Ludwig’s angina Loss of sensation in the lower lip may be produced by,CHECK ADC M07 A. Bell’s palsy B. Traumatic bone cyst C. Trigeminal neuralgia D. Fracture in the mandible first molar region E. Ludwig’s angina

Description : Loss of sensation in the lower lip may be produced by,CHECK ADC M07 A. Bell’s palsy B. Traumatic bone cyst C. Trigeminal neuralgia D. Fracture in the mandible first molar region E. Ludwig’s angina

Last Answer : D. Fracture in the mandible first molar region E. Ludwig’s angina

Before filling a class V abrasion cavity with GIC you should(+adc March07) A. Clean with pumice, rubber cup, water and weak acid B. Dry the cavity thoroughly before doing anything C. Acid itch cavity then dry thoroughly

Description : Before filling a class V abrasion cavity with GIC you should(+adc March07) A. Clean with pumice, rubber cup, water and weak acid B. Dry the cavity thoroughly before doing anything C. Acid itch cavity then dry thoroughly

Last Answer : A. Clean with pumice, rubber cup, water and weak acid

Define ADC and DAC. Write two applications of each.

Description : Define ADC and DAC. Write two applications of each.

Last Answer : ADC An analog to digital converter (ADC), converts any analog signal into quantifiable data, which makes it easier to process and store, as well as more accurate and reliable by ... signal, hence any analog circuit can work with digital system Application - Microcontroller, washing machine