What is gap between the electrodes in transformer oil testing kit?

What is gap between the electrodes in transformer oil testing kit?
by

1 Answer

Answer :

0.1 Inch.
by

Related questions

What maintenance of earth electrodes should be done?

Description : What maintenance of earth electrodes should be done?

Last Answer : The neighbouring soil to the earth electrode shall be kept moist where necessary, by periodically pouring water through a pipe where fitted along with it or by pouring water in the immediate ... wherever available, shall be carried out to ensure their rigidity and other signs of deterioration. 

Electric resistance seam welding uses __________ electrodes. (A) Pointed (B) Disc. (C) Flat (D) Domed

Description : Electric resistance seam welding uses __________ electrodes. (A) Pointed (B) Disc. (C) Flat (D) Domed

Last Answer : Ans: B Disc type electrodes are used for electric resistance seam welding.

Why it is sometimes necessary to preheat the base material before welding? a) To remove oil and grease b) To remove moisture from inside the material c) To prevent the possible risk of cracking d) Not required if using cellulosic electrodes as these will provide enough heat

Description : Why it is sometimes necessary to preheat the base material before welding? a) To remove oil and grease b) To remove moisture from inside the material c) To prevent the possible risk of cracking d) Not required if using cellulosic electrodes as these will provide enough heat

Last Answer : c) To prevent the possible risk of cracking

Where can I buy a blood type testing kit?

Description : Where can I buy a blood type testing kit?

Last Answer : There are plenty of blood type testing kits online. You can purchase on www.4yourtype.com. Another is www.homehealthtest.com for $9.95. You can always go to your doctor and easily receive a blood test there.

What is the most convenient kit to use for testing blood type?

Description : What is the most convenient kit to use for testing blood type?

Last Answer : The easiest blood typing kit to buy is the Blood Type Eldoncard Typing Test Kit. It is available at Amazon.com for about $13.00. The process involves a simple finger prick and easy to read results.

Stones are provided in the substation to: a) To avoid fire accident by draining oil from transformer if leaks b) To avoid growing of weeds and plants c) To provide insulation d) All the above

Description : Stones are provided in the substation to: a) To avoid fire accident by draining oil from transformer if leaks b) To avoid growing of weeds and plants c) To provide insulation d) All the above

Last Answer : Ans: D

Figure 'B' shown in the illustration represents a/an ____________. EL-0091 A. magnetic amplifier B. Scott-T transformer C. saturable-core reactor D. oil-filled toroid

Description : Figure 'B' shown in the illustration represents a/an ____________. EL-0091 A. magnetic amplifier B. Scott-T transformer C. saturable-core reactor D. oil-filled toroid

Last Answer : Answer: A

Figure 'A' shown in the illustration represents a/an _______________. EL-0091 A. magnetic amplifier B. Scott-T transformer C. saturable-core reactor D. oil-filled toroid

Description : Figure 'A' shown in the illustration represents a/an _______________. EL-0091 A. magnetic amplifier B. Scott-T transformer C. saturable-core reactor D. oil-filled toroid

Last Answer : Answer: C

Which type of oil is used as a transformer oil?

Description : Which type of oil is used as a transformer oil?

Last Answer : Transformer oil, or insulating oil, is usually a highly-refined mineral oil that is stable at high temperatures and has excellent electrical insulating properties. It is used in oil filled ... life, readily biodegradable, and have a lower volatility and higher flash points than mineral oil.

What is the function of transformer oil?

Description : What is the function of transformer oil?

Last Answer : A. Transformer Oil serves mainly two purposes 1. It acts as liquid insulation in electrical power transformer 2. It dissipates heat of the transformer i.e acts as coolant. In addition to these ... acid (C7, C8) esters are also becoming increasingly common as alternatives to naphthenic mineral oil.

Why transformer oil is used as a cooling medium?

Description : Why transformer oil is used as a cooling medium?

Last Answer : When transformer oil is used as a coolant the heat dissipation by convection is 10 times more than the convection due to air. Hence transformer oil is used as a cooling medium.

What is the function of transformer oil in a transformer ?

Description : What is the function of transformer oil in a transformer ?

Last Answer : Transformer oil provides , (i)good insulation and (ii)cooling . Nowadays instead of natural mineral oil, synthetic oils known as ASKRELS (trade name ) are used. They are non-inflammable ... an electric arc do not decompose to produce inflammable gases. PYROCOLOR oil possess high dielectric strength.

What is oil immersed type transformer?

Description : What is oil immersed type transformer?

Last Answer : In this type of transformer, oil is used as coolant. Entire assembly including core and windings is kept immersed in oil. The developed heat is transferred to the walls of tank through oil. Finally the heat is transferred to the surrounding air from tank wall by radiation.

What are the types of oil used for in transformer for cooling?

Description : What are the types of oil used for in transformer for cooling? 

Last Answer : Paraffin based and naphtha based (in INDIA)  

Why there is no mixing of oil of tap changer and transformer?

Description : Why there is no mixing of oil of tap changer and transformer?

Last Answer : When the tap changing takes place arc is struck between the contacts. Due to this the oil inside the tap changer will be highly carbonised. If both oil get mixed up the quality of transformer tank oil will come down. This is not advisable. Hence both oils are kept separately. 

What is the requirement oil in a transformer?

Description : What is the requirement oil in a transformer?

Last Answer : Oil is used removal of heat produced in the transformer and also as insulating medium. 

Mention the properties of transformer oil.

Description : Mention the properties of transformer oil.

Last Answer : Properties of transformer oil are, a) Colour – pale yellow. b) Moisture content -

What is the normal value of moisture content allowed in transformer oil?

Description : What is the normal value of moisture content allowed in transformer oil? 

Last Answer :

Unnecessary and frequent applications of varnish to the generator windings to repair defective insulation will result in ____________. A. heavy coatings of varnish interfering with heat dissipation B. deficient air gap clearance and eventual damage to the casing C. failure of the rectifier assembly D. a built-up of varnish without changing generator operation

Description : Unnecessary and frequent applications of varnish to the generator windings to repair defective insulation will result in ____________. A. heavy coatings of varnish interfering with heat dissipation B. ... of the rectifier assembly D. a built-up of varnish without changing generator operation

Last Answer : Answer: A

The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END-AFT END, Top .045 - .049, Right Side .045 - .047, Left Side .045 - .047, Bottom .045 - .041 Which of the f A. both the aft and foward bearings should be replaced. B. Shims should be removed from the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Description : The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END-AFT END, Top .045 - .049, Right Side .045 - .047, Left ... the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Last Answer : Answer: A

Air gap readings should be taken on electrical generation machinery periodicly to _________. I. determine the need for cleaning II. check the condition of the bearings A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings should be taken on electrical generation machinery periodicly to _________. I. determine the need for cleaning II. check the condition of the bearings A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: B

Air gap readings for electrical generating equipment should be taken periodicly. This is to _______. I. determine the condition of the bearings II. prevent damage to the rotor and stator A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings for electrical generating equipment should be taken periodicly. This is to _______. I. determine the condition of the bearings II. prevent damage to the rotor and stator A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: C

Air gap readings should be taken on electrical generation equipment periodicly to ________. I. check machine effeciency II. determine the need for cleaning A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings should be taken on electrical generation equipment periodicly to ________. I. check machine effeciency II. determine the need for cleaning A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: D

Air gap readings should be periodicly taken for electrical generation equipment. The best tool to use to take these measurements is a ___________. A. cloth (non-metalic) tape measure B. dial indicator C. inside micrometer D. tapered, long blade, feeler gage

Description : Air gap readings should be periodicly taken for electrical generation equipment. The best tool to use to take these measurements is a ___________. A. cloth (non-metalic) tape measure B. dial indicator C. inside micrometer D. tapered, long blade, feeler gage

Last Answer : Answer: D

If air gap readings for an electical generating machine have changed significantly from the last reading, you should check _________. A. the bearings B. insulation readings and machine cleanliness C. the prime mover thrust bearing D. the field coil bolts for the proper torque values

Description : If air gap readings for an electical generating machine have changed significantly from the last reading, you should check _________. A. the bearings B. insulation readings and machine cleanliness C. the prime mover thrust bearing D. the field coil bolts for the proper torque values

Last Answer : Answer: A

Air gap readings should be taken periodicly on electrical generation equipment to __________. A. determine the amount of varnish that can be applied to correct insulation problems B. determine the condition of the bearings C. provide for the correct proper tightening of the field coil bolts and correct lateral adjustment of the field coils D. increase machine efficiency

Description : Air gap readings should be taken periodicly on electrical generation equipment to __________. A. determine the amount of varnish that can be applied to correct insulation problems B. determine the ... field coil bolts and correct lateral adjustment of the field coils D. increase machine efficiency

Last Answer : Answer: B

The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END -AFT END, Top .045 - .049 , Right Side .045 - .047, Left Side .045 - .047 , Bottom .045 - .041 Which of the fo A. The aft bearing should be realigned or replaced. B. Shims should be removed from the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Description : The following air gap readings were obtained from a horizontally mounted, bilge pump, induction motor, equipped with sleeve bearings: FWD END -AFT END, Top .045 - .049 , Right Side .045 - .047, Left ... the aft bearing. C. The forward bearing should be lowered. D. The aft bearing should be lowered.

Last Answer : Answer: A

The air gap in an induction motor should be checked periodically with a feeler gage to detect ____________. A. rotor contact with the laminations B. changes in armature magnetic strength C. excessive bearing wear D. electrical damage to the rotor

Description : The air gap in an induction motor should be checked periodically with a feeler gage to detect ____________. A. rotor contact with the laminations B. changes in armature magnetic strength C. excessive bearing wear D. electrical damage to the rotor

Last Answer : Answer: C

The air gap in an induction motor should be periodically checked with a feeler gage to prevent possible ___________. A. rotor contact with the stator B. axial misalignment of the rotor C. damage to the motor bearings D. electrical damage to the bearings

Description : The air gap in an induction motor should be periodically checked with a feeler gage to prevent possible ___________. A. rotor contact with the stator B. axial misalignment of the rotor C. damage to the motor bearings D. electrical damage to the bearings

Last Answer : Answer: A

The air gap provided in induction motors should be checked periodically with a feeler gage to detect an unequal air gap and _____________. A. decreased motor magnetizing current B. hysteresis loses C. increased power factor D. mechanical damage to the rotor

Description : The air gap provided in induction motors should be checked periodically with a feeler gage to detect an unequal air gap and _____________. A. decreased motor magnetizing current B. hysteresis loses C. increased power factor D. mechanical damage to the rotor

Last Answer : Answer: D

The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Description : The voltage output of an AC generator is accurately controlled by _____________. A. changing the sensitivity of the prime mover to large changes in voltage B. varying the reluctance of the air gap C. varying the DC exciter voltage D. shorting out part of the armature windings

Last Answer : Answer: C

A loud buzzing noise coming from the contacts in a magnetic controller can be caused by ____________. A. excessive current B. excessive magnet gap C. bouncing of contacts D. dirt on magnet faces

Description : A loud buzzing noise coming from the contacts in a magnetic controller can be caused by ____________. A. excessive current B. excessive magnet gap C. bouncing of contacts D. dirt on magnet faces

Last Answer : Answer: D

Magnetic controller contacts may become welded together during operation because of _____________. A. excessive magnetic gap B. low contact pressure C. an open coil D. excessive ambient temperature

Description : Magnetic controller contacts may become welded together during operation because of _____________. A. excessive magnetic gap B. low contact pressure C. an open coil D. excessive ambient temperature

Last Answer : Answer: B

The horizontal line which cuts across 'L1' shown in figure 'A' of the illustration indicates a/an ______________. EL-0091 A. iron core B. saturable core C. air gap D. capacitive coupling

Description : The horizontal line which cuts across 'L1' shown in figure 'A' of the illustration indicates a/an ______________. EL-0091 A. iron core B. saturable core C. air gap D. capacitive coupling

Last Answer : Answer: B

Magnetic controller contacts may become welded together during operation due to _____________. A. an open coil B. low contact pressure C. excessive ambient temperature D. excessive magnetic gap

Description : Magnetic controller contacts may become welded together during operation due to _____________. A. an open coil B. low contact pressure C. excessive ambient temperature D. excessive magnetic gap

Last Answer : Answer: B

The rotor slots of a repulsion-type motor are generally skewed (placed nonparallel to the rotor axis) to _________. A. produce a constant starting torque B. permit a greater air gap with the starter C. permit a smaller air gap with the starter D. reduce eddy current losses

Description : The rotor slots of a repulsion-type motor are generally skewed (placed nonparallel to the rotor axis) to _________. A. produce a constant starting torque B. permit a greater air gap with the starter C. permit a smaller air gap with the starter D. reduce eddy current losses

Last Answer : Answer: A

Why The Air Gap Between The Pole Pieces And The Armature Is Kept Very Small?

Description : Why The Air Gap Between The Pole Pieces And The Armature Is Kept Very Small?

Last Answer : The air gap between the pole pieces and the armature is kept very small to keep the field strength at its highest value. This is due to the reason the flux lines can pass through iron very ... must be the magnetizing force to produce the required voltage hence the air gap is kept very small.

What happens if the air gap flux density in an induction motor increases?

Description : What happens if the air gap flux density in an induction motor increases?

Last Answer : The increase in air gap flux increases iron loss and hence efficiency decreases.

Why the air gap of an induction motor is made as small as possible?

Description : Why the air gap of an induction motor is made as small as possible?

Last Answer : The mmf and the magnetizing current are primarily decided by length of air gap. If air gap is small then mmf and magnetizing current will be low, which in turn increase the value of power factor. Hence by keeping small air gap, high power factor is achieved.

What happens if the air gap length is doubled?

Description : What happens if the air gap length is doubled?

Last Answer : If the air gap of an induction motor is doubled then the mmf and magnetizing current approximately doubles. Also increase in air gap length increases the overload capacity, offers better cooling, reduces noise and reduces unbalanced magnetic pull.

What are the advantages and disadvantages of large air gap length in induction motor?

Description : What are the advantages and disadvantages of large air gap length in induction motor?

Last Answer : Advantage: A large air gap length results in higher overload capacity, better cooling, reduction in noise and reduction in unbalanced magnetic pull. Disadvantages: The disadvantage of large air gap length is that it results in high value of magnetizing current.

In an induction machine, if the air gap increased a) Speed will be reduced b) Efficiency will be improved c) Power factor will be lowered d) Breakdown torque will be reduced

Description : In an induction machine, if the air gap increased a) Speed will be reduced b) Efficiency will be improved c) Power factor will be lowered d) Breakdown torque will be reduced

Last Answer : Ans: Power factor will be lowered

The current zero interruption, in oil and air blast circuit breakers, is achieved by (a) lengthening of the gap (b) cooling and blast effect (c) both (a) and (b) (d) deionizing the oil with forced air (e) none of the above

Description : The current zero interruption, in oil and air blast circuit breakers, is achieved by (a) lengthening of the gap (b) cooling and blast effect (c) both (a) and (b) (d) deionizing the oil with forced air (e) none of the above

Last Answer : (c) both (a) and (b)

When the sample of copper with the zinc impurity is to be purified by electrolysis, the appropriate electrodes are

Description : When the sample of copper with the zinc impurity is to be purified by electrolysis, the appropriate electrodes are

Last Answer : When the sample of copper with the zinc impurity is to be purified by electrolysis, the appropriate electrodes ... "),("Pure Zinc","ImPure Zinc"):}`

Brine is electrolysed by using inert electrodes. The reaction at anode is_______

Description : Brine is electrolysed by using inert electrodes. The reaction at anode is_______

Last Answer : Brine is electrolysed by using inert electrodes. The reaction at anode is_______ A. `Cl^(-)(aq.)rarr(1)/(2)Cl_(2) ... )H_(2)(g),E_("cell")^(o.)=0.00V`

When the sample of Cu with Zn as impurity is to be purified by electrolysis, the appropriate electrodes are :

Description : When the sample of Cu with Zn as impurity is to be purified by electrolysis, the appropriate electrodes are :

Last Answer : When the sample of Cu with Zn as impurity is to be purified by electrolysis, the appropriate electrodes are ... 4)","Impure zinc","Impure sample"):}`

Brine is electrolysed by using inert electrodes. The reaction at anode is_______

Description : Brine is electrolysed by using inert electrodes. The reaction at anode is_______

Last Answer : Brine is electrolysed by using inert electrodes. The reaction at anode is_______ A. `Cl^(-)(aq)to(1)/(2)Cl_(2 ... 2)H_(2)(g), E_(Cell)^(otimes)=0.00V`

In what situation might in be better to position the electrodes on the upper arm and the thighs rather than lower on the arms and legs?

Description : In what situation might in be better to position the electrodes on the upper arm and the thighs rather than lower on the arms and legs?

Last Answer : Need answer

What are the half-reactions for galvanic cell with Ni and Mg electrodes?

Description : What are the half-reactions for galvanic cell with Ni and Mg electrodes?

Last Answer : Ni2+(aq) + 2e- Ni(s) and Mg(s) Mg2+(aq) + 2e-

What is oxidized in galvanic cell made with silver and nickel electrodes?

Description : What is oxidized in galvanic cell made with silver and nickel electrodes?

Last Answer : The nickel metal(apex)