For how long 220 V DC batteries can supply power UPS?

For how long 220 V DC batteries can supply power UPS? 
by

1 Answer

Answer :

220 V DC batteries can supply Power UPS for 30 minutes. Within this time class III power supply should be restored by DG’s.  
by

Related questions

If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC

Description : If the supply voltage is 220 volts 60 Hz, what is the operating voltage of the motor controller circuitry illustrated? EL-0011 A. 110 volts DC B. 110 volts AC C. 220 volts DC D. 220 volts AC

Last Answer : Answer: D

What happen if we give 220 volts dc supply to the bulb or tube light?

Description : What happen if we give 220 volts dc supply to the bulb or tube light?

Last Answer : Bulbs [devices] for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current through lamp would be so high that it may damage the bulb element.

What Happen If We Give 220 Volts Dc Supply To D Bulb R Tube Light?

Description : What Happen If We Give 220 Volts Dc Supply To D Bulb R Tube Light?

Last Answer : Bulbs [devices] for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current through lamp would be so high that it may damage the bulb element.

what happens if we give 220 volts dc supply to the bulb or tube light?

Description : what happens if we give 220 volts dc supply to the bulb or tube light?

Last Answer : A:Bulbs [devices] for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current ... be so high that it may damage the bulb element. Low dc voltage will not damage the appliances

What happen if we give 220 volts dc supply to bulb or tube light?

Description : What happen if we give 220 volts dc supply to bulb or tube light?

Last Answer : Bulbs or devices for AC are designed to operate such that it offers high impedance to AC supply. Normally they have low resistance. When DC supply is applied, due to low resistance, the current through lamp would be so high that it may damage the bulb element.

A 220/440 V, 50 Hz, 5 KVA, single phase transformer operates on 220V, 40Hz supply with secondary winding open circuited. Then (A) Both eddy current and hysteresis losses decreases. (B) Both eddy current and hysteresis losses increases. (C) Eddy current loss remains the same but hysteresis loss increases. (D) Eddy current loss increases but hysteresis loss remains the same.

Description : A 220/440 V, 50 Hz, 5 KVA, single phase transformer operates on 220V, 40Hz supply with secondary winding open circuited. Then (A) Both eddy current and hysteresis losses decreases. (B) Both ... same but hysteresis loss increases. (D) Eddy current loss increases but hysteresis loss remains the same.

Last Answer : (A) Both eddy current and hysteresis losses decreases.

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : (C) 3.0 V.

What are the sources of 240 V AC class I supply? What are the functions of each part of UPS?

Description : What are the sources of 240 V AC class I supply? What are the functions of each part of UPS? 

Last Answer : Six sources. Three 20 kVA UPS for safety related loads. Two 60 kVA UPS for non-safety related loads. One 60 kVA UPS as a standby to safety related loads. These all UPS are back up by ... UPS into service. Manual bypass To take main UPS to maintenance by putting stand by UPS into service. 

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference...

Description : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

Last Answer : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is 40 V.

A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Description : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of 100 W lamps in parallel that can be tu

Last Answer : A factory is served by a 220 V supply line. In a circuit protected by a fuse marked 10 A, the maximum number of ... on, is A. 11 B. 22 C. 33 D. 66

A process electric heater is taking an hour to reach the desired temperature while operating at 440 V. It will take ------- hours to reach the same temperature if the supply voltage is reduced to 220 V. a) 2 b) 3 c) 4 d) 5

Description : A process electric heater is taking an hour to reach the desired temperature while operating at 440 V. It will take ------- hours to reach the same temperature if the supply voltage is reduced to 220 V. a) 2 b) 3 c) 4 d) 5

Last Answer : c) 4

If a 220 V heater is used on 110 V supply, the heat produced by it will be nearly

Description : If a 220 V heater is used on 110 V supply, the heat produced by it will be nearly (a) one half (b) twice (c) one-fourth (d) four times 

Last Answer : If a 220 V heater is used on a 110 V supply, the heat produced by it will be significantly less than it would be if it were used on a 220 V supply. This is because the heater is designed to operate ... the heater, but it will be significantly less than it would be if it were used on a 220 V supply.

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be (A) 3.6 V. (B) 2.5 V. (C) 3.0 V. (D) 6.0 V.

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be 3.0 V.

If a 220/440 V, 50 Hz, 5 KVA, single-phase transformer operates on 220V, 40Hz supply with secondary winding...

Description : If a 220/440 V, 50 Hz, 5 KVA, single-phase transformer operates on 220V, 40Hz supply with secondary winding open circuited: (A) both the eddy current and the hysteresis losses will decrease ... losses will increase (D) eddy current losses will increase but the hysteresis losses will remain the same

Last Answer : If a 220/440 V, 50 Hz, 5 KVA, single-phase transformer operates on 220V, 40Hz supply with secondary winding open circuited: both the eddy current and the hysteresis losses will decrease

The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary ...

Description : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be; (A) 3.6 (B) 2.5 V (C) 3.0 V (D) 6.0 V

Last Answer : The primary winding of a 220/6 V, 50 Hz transformer is energised from 110 V, 60 Hz supply. The secondary output voltage will be: 3.0 V

The electrical energy necessary to power a sound-powered telephone's small vibrating bell is obtained from _________. A. the emergency batteries for the general alarm B. each station's hand-cranked generator C. the emergency switchboard D. normal 115 volt DC supplies

Description : The electrical energy necessary to power a sound-powered telephone's small vibrating bell is obtained from _________. A. the emergency batteries for the general alarm B. each station's hand-cranked generator C. the emergency switchboard D. normal 115 volt DC supplies

Last Answer : Answer: B

What are the protections adopted in UPS or PMCC supply?

Description : What are the protections adopted in UPS or PMCC supply?

Last Answer : LV (incomer) or UPS input CTZM, Over current, Short circuit protections PMCC S or T input or UPS output Under voltage (27), 51RYB, 51N protections. 

Before using an all-purpose electric measuring instrument (multimeter) utilizing internal batteries to supply power for resistance measurements, you should FIRST ____________. A. remove one of the batteries B. remove all the batteries C. calibrate using a known external resistance D. select the proper resistance range

Description : Before using an all-purpose electric measuring instrument (multimeter) utilizing internal batteries to supply power for resistance measurements, you should FIRST ____________. A. remove one of the ... batteries C. calibrate using a known external resistance D. select the proper resistance range

Last Answer : Answer: D

You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should _____________. A. replace the batteries in the instrument B. measure resistance by dividing the voltmeter indication by the ammeter indication C. set the pointer using a bridge D. change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Description : You are calibrating a multimeter using internal batteries to supply power for resistance measurements. However, you are unable to adjust the pointer to 'zero' using the adjustment knob. Therefore, you should ... change scales to the R X 100 scale and adjust using the 'zero ohms' adjusting knob

Last Answer : Answer: A

A supply of 24 V DC is applied across a circuit which consist of three resistors connected in parallel R1= 1.2KΩ, R2= 560 Ω, R3= 2.1Ω and a fourth resistor of 7.8 Ω connected in series with the parallel group. Determine the current, voltage and power across each resistor

Last Answer : Req= (1/1200 +1/560 + 1/2.1)^-1        = 2.1 ohms RT= 2.1 + 7.8      = 9.9 ohms IT = V/R = 24/9.9                = 2.4 A Veq= R I =  2.1 2 ... 7.8         = 12.096 w                 = 44.928 w _________________________________________ By: Ellis-Junior Kamatjipose [email protected]

When a battery-charging panel is being used, the batteries will discharge if _____________. A. DC voltage is supplied B. the polarity is reversed C. the voltage fluctuates D. too little current is supplied

Description : When a battery-charging panel is being used, the batteries will discharge if _____________. A. DC voltage is supplied B. the polarity is reversed C. the voltage fluctuates D. too little current is supplied

Last Answer : Answer: B

A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the proper connections for across the line starting B. the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Description : A series wound DC motor has its armature and field connected in series with a resistor. When the motor is disconnected from its power supply, this motor will exemplify __________. A. the ... the proper connections for an automatic strip heater C. a reversing controller circuit D. dynamic braking

Last Answer : Answer: D

In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 1 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR2 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal ... 2 at 9.1 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1 AMPLIFIER MODULE is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply from common B. a variable resistor diode to control the output to ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: A

In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls the input to terminal 10 C. a zener diode that regulates the voltage to terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Description : In the illustration, the component VR1 on the A1A1 PCB is _________. EL-0060 A. a zener diode to regulate the +9 volt power supply B. a variable resistor diode to control the output to terminal 9 that controls ... terminal 9 at 6.6 volts DC D. a tunnel diode with a breakdown voltage of 6.6 Volts DC

Last Answer : Answer: C

The 24 volt DC bus on the emergency switchboard is used to supply power to the _____________. A. general alarm system B. gyrocompass power failure alarm system C. smoke detection system D. all of the above

Description : The 24 volt DC bus on the emergency switchboard is used to supply power to the _____________. A. general alarm system B. gyrocompass power failure alarm system C. smoke detection system D. all of the above

Last Answer : Answer: D

Which of the listed sections of an emergency switchboard is used to supply power for alarm signals under emergency conditions? A. The generator and bus transfer section B. The 450 volt, 60 cycle, 3 phase bus C. The 120 volt, 3 phase, 60 cycle bus D. The 24 volt DC bus

Description : Which of the listed sections of an emergency switchboard is used to supply power for alarm signals under emergency conditions? A. The generator and bus transfer section B. The 450 volt, 60 cycle, 3 phase bus C. The 120 volt, 3 phase, 60 cycle bus D. The 24 volt DC bus

Last Answer : Answer: D

AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Description : AC and DC generators are similar in that they _____________. A. both generate alternating voltages B. both rectify the voltage before delivery C. are constructed at the same physical size for the same kilowatt rating D. both supply three-phase power

Last Answer : Answer: A

Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

What features should I look for in a UPS (uninterruptible power supply)?

Description : What features should I look for in a UPS (uninterruptible power supply)?

Last Answer : answer:If that's all you need the UPS for: to handle tiny burps' in the power supply, then you can get by with the cheapest, most generic UPS that you can find. Seriously. You need next to ... 'd have switched to a laptop long ago (which is my home computer now, anyway) for just that reason.

n electrochemical cell which is used as a source of direct electrical current at constant voltage under standard conditions is called a – (1) Power transmittor (2) Battery (3) Uninterrupted power supply (UPS) (4) Generator

Description : n electrochemical cell which is used as a source of direct electrical current at constant voltage under standard conditions is called a – (1) Power transmittor (2) Battery (3) Uninterrupted power supply (UPS) (4) Generator

Last Answer : (3) Uninterrupted power supply (UPS) Explanation: A Galvanic cell, also known as battery, is an electro-chemical cell that derives electrical energy from spontaneous redox reactions taking place within ... produce direct current. A battery is a set of galvanic cells that are connected in parallel.

UPS is now widely use in households. What does UPS stands for ? A. Uniform Power Storage B. Universal Product Support C. Under Panel Storage D. Uninterruptible Power Supply (Answer)

Description : UPS is now widely use in households. What does UPS stands for ? A. Uniform Power Storage B. Universal Product Support C. Under Panel Storage D. Uninterruptible Power Supply (Answer)

Last Answer : D. Uninterruptible Power Supply (Answer)

________carries fans and a special port designed for power supply. a) UPS b) Mother Board c) Monitor d) None of These

Description : ________carries fans and a special port designed for power supply. a) UPS b) Mother Board c) Monitor d) None of These

Last Answer : b) Mother Board

An electrochemical cell which is used as a source of direct electrical current at constant voltage under standard conditions is called a : (1) Power transmittor (2) Battery (3) Uninterrupted power supply (UPS) (4) Generator

Description : An electrochemical cell which is used as a source of direct electrical current at constant voltage under standard conditions is called a : (1) Power transmittor (2) Battery (3) Uninterrupted power supply (UPS) (4) Generator

Last Answer : Battery

2. An electric oven of 2 kW power rating is operated in a domestic electric circuit (220 V) that has a current rating of 5 A. What result do you expect? Explain. -Physics-10

Description : 2. An electric oven of 2 kW power rating is operated in a domestic electric circuit (220 V) that has a current rating of 5 A. What result do you expect? Explain. -Physics-10

Last Answer : The current drawn by the electric oven can be calculated using the formula P = V × I I = P/V Substituting the values, we get I = 2000 W/220 V = 9.09 A The current drawn by the electric oven is 9.09 A which exceeds the safe limit of the circuit. This causes the fuse to melt and break the circuit.

Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Description : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Last Answer : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power ... B. 160 W C. `37.5 W` D. 60 W

Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Description : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power dissipated is

Last Answer : Two bulbs 60 W and 100 W designed for voltage 220 V are connected in series across 220 V source. The net power ... `37.5` W B. 75W C. 80W D. 40 W

A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to

Last Answer : A fridge uses 220 watts from 110 V power source. The Fridge then draws a current from the source equal to 2 amps.

An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Description : An AC supply of 230 V is applied to half wave rectifier circuit. A transformer turns ratio is 20 : 1. Find i) Output DC voltage (ii) Peak Inverse Voltage (PIV)

Last Answer : Solution:

A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A

Description : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be:

Last Answer : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be: 2.4 kOhm

Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply.

Description : Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: A) 195 volt B) 220 volt C) 245 volt D) 440 volt

Last Answer : Two 220 volt lamps, one of 60 watt and the other of 75 watt are connected in series across a 440 volt supply. The potential difference across 60 watt lamp will be: 245 volt

A DC generator is used to supply direct current in order to maintain an AC generator field and is known as a/an _____________. A. rotor B. stator C. exciter D. armature

Description : A DC generator is used to supply direct current in order to maintain an AC generator field and is known as a/an _____________. A. rotor B. stator C. exciter D. armature

Last Answer : Answer: C

Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card

Description : Normally, the FIRST step in troubleshooting a transistor circuit card is to _____________. A. carefully remove the transistors from the card B. give the circuit an initial test with a signal generator C. test for continuity with a low voltage DC supply D. visually inspect the card

Last Answer : Answer: D

The electrical supply applied to the anodes shown in the illustration is _____________. EL-0090 A. low voltage, high current DC B. low voltage, high current AC C. high voltage, low current DC D. high voltage, low current AC

Description : The electrical supply applied to the anodes shown in the illustration is _____________. EL-0090 A. low voltage, high current DC B. low voltage, high current AC C. high voltage, low current DC D. high voltage, low current AC

Last Answer : Answer: A

A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Description : A solid-state circuit is inoperative; the FIRST action that should be taken is to ____________. A. wiggle all the components to check for loose connections B. check all the resistors C. change all transistors D. check the DC supply voltage

Last Answer : Answer: D

The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Description : The most common source of excitation for synchronous motors is a/an ______________. A. stepup transformer B. half-wave rectifier C. DC supply D. AC supply

Last Answer : Answer: C

The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Description : The most common source of excitation for synchronous motors is a/an _____________. A. low voltage battery B. motor attenuator set C. DC exciter generator D. AC supply

Last Answer : Answer: C

What happen when Transformer is given DC supply ?

Description : What happen when Transformer is given DC supply ?

Last Answer : When DC supply is given to the transformer primary winding no back emf is induced in the transformer. Importance of Back emf is that it limits the current drawn by the machine. In the absence ... in burning down of primary winding. So when dc supply is given to transformer primary windings will burn

What will happen if DC supply is given on the primary of a transformer?

Description : What will happen if DC supply is given on the primary of a transformer?

Last Answer : A. Mainly transformer has high inductance and low resistance. In case of DC supply there is no inductance, only resistance will act in the electrical circuit. So, high electrical current will flow through primary side of the transformer. Due to this the coil and insulation will burn out.

What is the distribution of DC control supply in CL IV, III, II- 415V and 6.6 kV?

Description : What is the distribution of DC control supply in CL IV, III, II- 415V and 6.6 kV?

Last Answer : Closing coil and Trip coil 2 supply from one source. Trip coil 1 supply from one source. Protections supply from one source.