Why main generator/UT is not provided with separate overfluxing protection?

Why main generator/UT is not provided with separate overfluxing protection?
by

1 Answer

Answer :

Since GT is provided with overfluxing protection, it is adequate to protect main generator / UT also. Main generator can withstand higher degree of overfluxing. If a generator CB is used, separate overfluxing protection is essential for main generator. 
by

Related questions

Overfluxing protection is recommended for (a) distribution transformer (b) generator transformer of the power plant (c) auto-transformer of the power plant (d) station transformer of the power plant

Description : Overfluxing protection is recommended for (a) distribution transformer (b) generator transformer of the power plant (c) auto-transformer of the power plant (d) station transformer of the power plant

Last Answer : (b) generator transformer of the power plant

Overfluxing protection is recommended for?

Last Answer : Overfluxing protection is recommended for generator transformer of the power plant.

Purpose of standby E/F protection in SUT/UT?

Description : Purpose of standby E/F protection in SUT/UT? 

Last Answer : Back up for LV winding, LV neutral CT- CDG 12 – resistance earthing – relay set high time delay to discriminate with LV feeder and trip transformer if sustained E/F, also protects neutral earthing resistor.

Where fault level is more, whether in generator bus duct or UT bus duct? Why?

Description : Where fault level is more, whether in generator bus duct or UT bus duct? Why?

Last Answer : Fault level is more in UT bus duct. Because the fault currents fed by the both generator and GT adds up within UT bus duct in case there is a fault in UT bus duct. 

Why REF is provided in the LV side of SUT and UT?

Description : Why REF is provided in the LV side of SUT and UT? 

Last Answer : The LV sides of the two transformers are earthed through the resistance. This will limit the flow of current in case of LV earth fault. Hence the differential protection may not act for a LV earth fault. Hence ref protection is provided. 

Why inter-turn protection is provided along with differential protection in generator?

Description : Why inter-turn protection is provided along with differential protection in generator?

Last Answer : Inter-turn protects two separate windings from the fault of the generator.  

Why 100% winding protection is felt essential for main generator stator E/F protection? (Used in NAPS onwards?)

Description : Why 100% winding protection is felt essential for main generator stator E/F protection? (Used in NAPS onwards?)  

Last Answer : At MAPS 4% of winding is not protected. Earlier felt that the Electro magnetic stress due high external fault currents near 4% of neutral may not be high to cause E/F here. But now felt that the mechanical stress can leads to E/F. 

How main generator protection grouped?

Description : How main generator protection grouped?

Last Answer : The various protections associated with the generator, Generator transformer and Unit transformer are connected to a trip unit through trip relays 86A, 86B and 86C. The protective levels of generator are in ... breaker. During Class C trip, the generator will come on House load mode of operation.  

What is the purpose of back up impedance protection in main generator?

Description : What is the purpose of back up impedance protection in main generator?  

Last Answer : Covers inter-phase faults both externals to the GT and in GT. This also covers partially faults inside generator, time delayed to coordinate with 230 kV-distance protection. 

Which of the following is/are true concerning electric power operated watertight door systems? A. Each motor driven door must use the main bus as its source of power. B. Each distribution panel for the system must be on the lowest level where berthing quarters are located. C. Distribution panels must not be provided with a means of locking in order to permit quick activation of the system. D. Each system must have a separate branch circuit.

Description : Which of the following is/are true concerning electric power operated watertight door systems? A. Each motor driven door must use the main bus as its source of power. B. Each distribution panel for ... to permit quick activation of the system. D. Each system must have a separate branch circuit.

Last Answer : Answer: D

The purpose of the reverse power relay, provided on a ship's service alternator panel, is to trip the circuit in the event of ______________. A. main circuit overload B. high power transfer C. generator overspeeding D. alternator motorization

Description : The purpose of the reverse power relay, provided on a ship's service alternator panel, is to trip the circuit in the event of ______________. A. main circuit overload B. high power transfer C. generator overspeeding D. alternator motorization

Last Answer : Answer: D

Which type of protection is provided on a generator to protect against stator insulation failure?

Description : Which type of protection is provided on a generator to protect against stator insulation failure? A) Differential protection B) Overcurrent relay C) Thermocouple actuated alarm D) Reverse power relay

Last Answer : Which type of protection is provided on a generator to protect against stator insulation failure? A) Differential protection B) Overcurrent relay C) Thermocouple actuated alarm D) Reverse power relay 

What are the protections for UT?

Description : What are the protections for UT?  

Last Answer : a) Differential protection b) LV restricted earthfault protection c) LV back up earthfault and over current protection d) Buchholz and high oil, winding temperature protection. 

Why UT, SUT secondary is rated for 6.9kV where as bus voltage is 6.6kV?

Description : Why UT, SUT secondary is rated for 6.9kV where as bus voltage is 6.6kV? 

Last Answer : The no load secondary 6.9kV voltage level adequately takes into account voltage drop during loaded condition to cater station buses at 6.6kV level. 

Why the neutral is earthed through earthing resistance in case of UT and SUT?

Description : Why the neutral is earthed through earthing resistance in case of UT and SUT? 

Last Answer : This is done to limit the earth fault current.  

What is the vector group of GT, UT, SUT?

Description : What is the vector group of GT, UT, SUT?

Last Answer : Yd11 Dy1 Yy0 

During unit operation, can we parallel UT & SUT continuously?

Description : During unit operation, can we parallel UT & SUT continuously?

Last Answer : No, due to switchgear limitation.  

During unit operation can we have one UT feeding both unit 6.6 kV loads?

Description : During unit operation can we have one UT feeding both unit 6.6 kV loads? 

Last Answer : No, logically prevented.  

What is E/F current limit for SUT and UT?

Description : What is E/F current limit for SUT and UT?

Last Answer : 400a limited by 10 ohms resistor.  

The basic type of D.C. motor speed control where a generator armature directly feeds the motor armature and the motor and generator fields are excited by a separate D.C. source is called ___________________. A. Burmeister-Wain B. Ward-Leonard C. Sperry-Rand D. Atlas-Copco

Description : The basic type of D.C. motor speed control where a generator armature directly feeds the motor armature and the motor and generator fields are excited by a separate D.C. source is called ___________________. A. Burmeister-Wain B. Ward-Leonard C. Sperry-Rand D. Atlas-Copco

Last Answer : Answer: B

In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD winding through the voltage regulator. C. the controller to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Description : In the illustration, the component labeled 'EXC' is _______. EL-0003 A. a separate class II regulated DC generator for critical direct current loads B. a generator feeding the FLD ... to drive the governor for turbogenerator speed. D. the electronic driver for the switchboard metering circuits

Last Answer : Answer: B

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

In an AC generator, direct current from a separate source is passed through the windings of the rotor _____________. A. by means of slip rings and brushes B. by means of a commutator C. by means of rotating bar magnet D. to minimize the danger of arc over

Description : In an AC generator, direct current from a separate source is passed through the windings of the rotor _____________. A. by means of slip rings and brushes B. by means of a commutator C. by means of rotating bar magnet D. to minimize the danger of arc over

Last Answer : Answer: A

Where automatic restart does not present a hazard after a power failure, Coast Guard Regulations (46 CFR) require motor controllers for auxiliaries vital to the propelling equipment to be provided with ________________. A. overload protection B. low voltage protection C. low voltage release D. reverse current protection

Description : Where automatic restart does not present a hazard after a power failure, Coast Guard Regulations (46 CFR) require motor controllers for auxiliaries vital to the propelling equipment to be provided ... overload protection B. low voltage protection C. low voltage release D. reverse current protection

Last Answer : Answer: C

Which of the following statements is true concerning the motor controller diagram shown in the illustration? EL-0023 A. Terminal 'T2' is hot only on high speed. B. Both indicating lights will be lit on both high and low speeds as they are connected to the common lead when the motor is running. C. Overload protection is provided for high speed operation only. D. 'L2' is always connected to 'T2' whenever the motor is running.

Description : Which of the following statements is true concerning the motor controller diagram shown in the illustration? EL-0023 A. Terminal 'T2' is hot only on high speed. B. Both indicating lights will be lit on ... high speed operation only. D. 'L2' is always connected to 'T2' whenever the motor is running.

Last Answer : Answer: D

Protection against sustained overloads occurring in molded-case circuit breakers is provided by a/an __________. A. overvoltage release B. thermal acting trip C. thermal overload relay D. current overload relay

Description : Protection against sustained overloads occurring in molded-case circuit breakers is provided by a/an __________. A. overvoltage release B. thermal acting trip C. thermal overload relay D. current overload relay

Last Answer : Answer: B

How Transformer Protection provided for internal faults?

Description : How Transformer Protection provided for internal faults?

Last Answer : 1.Bucholz Relay (1st Stage Alarm and 2nd Stage Trip) 2.Sudden Pressure Relay (1st Stage Alarm and 2nd Stage Trip) 3.Pressure Relief Valve (1st Stage Alarm and 2nd Stage Trip) 4.Pressure Switch ... 8.Gas Temperature Indicator (Alarm) 9.Silicon Breather (Passive - no alarm) 10.Smoke Detector (Alarm)

Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Description : Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Last Answer : Answer: D

As shown in the illustration, the generator field is excited with DC current provided by ____________. EL-0016 A. conductors '1', '2' and '3' B. inductor 'L1' C. rectifier 'CR1' D. winding 'S-2'

Description : As shown in the illustration, the generator field is excited with DC current provided by ____________. EL-0016 A. conductors '1', '2' and '3' B. inductor 'L1' C. rectifier 'CR1' D. winding 'S-2'

Last Answer : Answer: C

Automatic voltage regulators provided on switchboards function to _____________. A. regulate the AC load on the generator B. protect the switchboard from high voltage C. govern prime mover speed to control voltage D. vary the field excitation to the generators

Description : Automatic voltage regulators provided on switchboards function to _____________. A. regulate the AC load on the generator B. protect the switchboard from high voltage C. govern prime mover speed to control voltage D. vary the field excitation to the generators

Last Answer : Answer: D

As load is added to an AC generator provided with constant field excitation, the prime mover slows down with the effect of ____________. A. lowering frequency and lowering generated voltage B. increasing frequency and increasing generated voltage C. increasing frequency and lowering generated voltage D. lowering frequency and increasing generated voltage

Description : As load is added to an AC generator provided with constant field excitation, the prime mover slows down with the effect of ____________. A. lowering frequency and lowering generated ... C. increasing frequency and lowering generated voltage D. lowering frequency and increasing generated voltage

Last Answer : Answer: A

What type of cooling is provided for Generator in power plant?

Description : What type of cooling is provided for Generator in power plant?

Last Answer : Hydrogen gas cooling is employed for large size generators because of better heat carrying ability of the hydrogen. Hydrogen cooling is provided for rotors and core of the generator. Water cooling is provided for the stator of the alternator.

Why generator differential provided?

Description : Why generator differential provided? 

Last Answer : For generator phase to phase faults and 3 phase faults. 

If the size of a column is reduced above the floor, the main bars of the columns, are (A) Continued up (B) Bent inward at the floor level (C) Stopped just below the floor level and separate lap bars provided (D) All the above

Description : If the size of a column is reduced above the floor, the main bars of the columns, are (A) Continued up (B) Bent inward at the floor level (C) Stopped just below the floor level and separate lap bars provided (D) All the above

Last Answer : Answer: Option D

Pick up the consideration to the taken while designing a hospital from the following: (A) The operation theatre unit to be detached as it requires sterilized zone but near the ward for the patients and doctor (B) The mortuary should be detached from the main circulation with a post-mortem room (C) Casualty unit should be provided a separate entrance (D) All the above

Description : Pick up the consideration to the taken while designing a hospital from the following: (A) The operation theatre unit to be detached as it requires sterilized zone but near the ward for the patients ... post-mortem room (C) Casualty unit should be provided a separate entrance (D) All the above

Last Answer : Answer: Option D

Discrimination between main and back up protection is provided by the use of relays which are (a) fact (b) sensitive (c) slow (d) none of the above

Description : Discrimination between main and back up protection is provided by the use of relays which are (a) fact (b) sensitive (c) slow (d) none of the above

Last Answer : (c) slow

Discrimination between main and backup protection is provided by the use of relays which are?

Last Answer : Discrimination between main and back up protection is provided by the use of relays which are slow.

The operating torque of the upper induction disc-type element, or timer element, of an AC reverse power relay is obtained from ____________. A. the main bus B. a separate battery source C. line voltage D. electromagnets

Description : The operating torque of the upper induction disc-type element, or timer element, of an AC reverse power relay is obtained from ____________. A. the main bus B. a separate battery source C. line voltage D. electromagnets

Last Answer : Answer: D

The heaters for the winch circuit shown in the illustration are powered from _____________. EL-0102 A. a separate source B. the winch main bus C. the master switch power circuit D. the contactor control circuit

Description : The heaters for the winch circuit shown in the illustration are powered from _____________. EL-0102 A. a separate source B. the winch main bus C. the master switch power circuit D. the contactor control circuit

Last Answer : Answer: A

The timer element found in a reverse power relay obtains its operating torque via _____________. A. line voltage B. the main bus C. electromagnets D. a separate battery source

Description : The timer element found in a reverse power relay obtains its operating torque via _____________. A. line voltage B. the main bus C. electromagnets D. a separate battery source

Last Answer : Answer: C

The purpose of the automatic bus transfer shown in the illustration is to ___________. EL-0014 A. stepdown voltage to the lighting distribution panel B. provide emergency power to the lighting distribution panel C. energize the emergency switchboard from the main switchboard D. provide overcurrent protection to the lighting distribution panel

Description : The purpose of the automatic bus transfer shown in the illustration is to ___________. EL-0014 A. stepdown voltage to the lighting distribution panel B. provide emergency power to ... emergency switchboard from the main switchboard D. provide overcurrent protection to the lighting distribution panel

Last Answer : Answer: B

The main difference between a motor control circuit containing low voltage protection and low voltage release is that the latter contains _____________. A. a magnetic operating coil B. normally open line contacts C. thermal-overload protection D. a momentary-contact start button

Description : The main difference between a motor control circuit containing low voltage protection and low voltage release is that the latter contains _____________. A. a magnetic operating coil B. normally open line contacts C. thermal-overload protection D. a momentary-contact start button

Last Answer : Answer: D

Good hiking/camping spots in UT and CO?

Description : Good hiking/camping spots in UT and CO?

Last Answer : Gotta hit Bryce or Zion in Utah for sure! Both are spectacular. Look into reservations for camping online first, you may need to reserve a night now with the summer tourist hub kicking into high gear. Colorado I am less sure of, traveled through but didn’t camp anywhere.

Nightlife in Mesquite (NV) and St. George (UT)?

Description : Nightlife in Mesquite (NV) and St. George (UT)?

Last Answer : Remember Utah is a semi-dry state for alcohol, so if partying is part of the equation…. you have to go through a little extra to get to a bar. Mesquite has over five or six casinos/resorts. I’ve eaten at Virgin River in Mesquite.

Should I go to grad school at UC Irvine or UT Austin?

Description : Should I go to grad school at UC Irvine or UT Austin?

Last Answer : I think that would depend entirely on each school’s program.

I'm ut mobile and I have to recharge 100 MB of data once a month, but they can't run, please advise

Description : I'm ut mobile and I have to recharge 100 MB of data once a month, but they can't run, please advise

Last Answer : Need Answer

What is the mystery greene discusses and why does he say ut is something we should all care about?

Description : What is the mystery greene discusses and why does he say ut is something we should all care about?

Last Answer : Feel Free to Answer

Moab, UT?

Description : Moab, UT?

Last Answer : Moab, UT is a great site to visit. Until the 1950's Moab did nothave much to offer. Charlie Steen discovered uranium there and thetown has grown very quickly since that time. In Moab, UT there ... using whitewater rafting or a person can rent awhitewater raft and take their own tour.Moab, UT is n

How do I go about finding a caregiver for my elderly mother in Provo, UT?

Description : How do I go about finding a caregiver for my elderly mother in Provo, UT?

Last Answer : First, check in the local community for recommendations. Even if you live far away, call your mother's pastor or someone else that she knows in the community and ask for recommendations. If ... servicemagic has licensed, bonded, insured and rated caregivers listed for provo and the service is free.