List the types of coupling used in BJT amplifier. 

1 Answer

Answer :

Types of coupling used in BJT amplifier:

i. Resistance capacitance (RC)coupling

ii. Impedance coupling

iii. Transformer coupling

iv. Direct coupling

Related questions

Description : Draw the circuit of complementary, symmetry push pull amplifier and explain its working.

Last Answer : COMPLEMENTRY SYMMETRY CLASS B PUSH PULL AMPLIFIER  Circuit Diagram:  Circuit description: * Two transistors one NPN & other PNP is used in the circuit so they are complementary to each other. ... conducts & NPN remains OFF.  So we get remaining half cycle in the output.

Description : Explain stagger tuned amplifier with the help of waveforms.

Last Answer : Circuit Diagram: Above figure shows two-stage tuned voltage amplifier. The stagger tuning in this circuit, may be achieved by resonating the tuned circuits L1C1 and L2C2 to slightly different ... outside the pass-band. Because of the stagger tuning there is a loss of voltage gain.

Description : Explain with circuit diagram and waveform the operation of class AB push pull power amplifier.

Last Answer : Class AB Push Pull Power Amplifier:  Circuit Diagram:  Circuit Decription: The circuit consists of two centre-tapped transformers T1 and T2, two identical transistors Q1 and Q2 , Resistor R and ... two halves & produces a full sine wave in the load resistor. Waveform :

Description : Define the term related to power amplifier. (i) Efficiency (ii) Voltage gain

Last Answer : (i) Efficiency: Efficiency of the power amplifier is defined as the ratio of maximum a.c. output power to the d.c. input power. Mathematically (ii) Voltage gain: Voltage gain of the power amplifier is defined as the ratio of output voltage to the input voltage. Mathematically,

Description : Sketch circuit diagram of common source FET Amplifier. State working principle of it.

Last Answer : Working: -  * When small a.c. signal is applied to the gate, it produces variation in the gate to source voltage. This produces variation in the drain current. As the gate to source ... and we get amplification. Thus the AC output voltage VDS is 180º out of phase with AC input voltage.

Description : Explain principle of feedback amplifier.

Last Answer : Block diagram of feedback amplifier:- Explanation:- * Feedback is a process of injecting some energy from the output and then it back to the input. The amplifier which use the feedback principle are ... Now, The quantity β = Vf /Vo is called as feedback ratio or feedback fraction.

Description : Describe the operation of double tuned amplifier with the help of neat circuit diagram and mention its applications.

Last Answer : Circuit diagram: Operation:  *The signal to be amplified is applied at the input terminal through the coupling capacitor CC  *The resonant frequency of the tuned circuit L1 C1 is made equal ... : (i) Radio and T .V broadcasting as tuning circuit. (ii) Wireless communication system.

Description : With the help of neat circuit diagram, explain the operation of voltage shunt type feedback amplifier.

Last Answer : Diagram:  Fig. shows common emitter transistor amplifier with a feedback resistor RF connected between its output and input terminals. This is collector to base biasing when the input signal is ... As IS = If + Ii it is shunt type therefore it voltage shunt negative feedback amplifier.

Description : Draw the circuit diagram of class AB power amplifier and describe its working.

Last Answer : Circuit diagram: Circuit Description: The circuit consists of two center-tapped transformers T1 and T2, two identical transistors Q1 and Q2 , Resistor R and diode D. The DC voltage ... and Q2 conduct, as soon as input cross zero, negative sinusoidal voltage will appear across load.

Description : Describe the operation of class-C type of power amplifier with the help of neat sketch.

Last Answer : Circuit diagram: Operation: * Class C power amplifier is a type of amplifier where the transistor conducts for less than one half cycle of the input signal. Less than one ... resonant circuit oscillates in one frequency (generally the carrier frequency) all other frequencies are attenuated. 

Description : State the need of tuned amplifier in electronic circuits.

Last Answer : Necessity of tuned amplifier: 1. Selection of the desired radio frequency signal. 2. Amplification of the selected signal to a selected voltage level.

Description : State advantages of negative feedback used in feedback amplifier.

Last Answer : Advantage of negative feedback amplifier: * Increased stability in gain * Increased bandwidth * Less amplitude and harmonic distortion * Decreased noise * Less frequency distortion * Less non-linear distortion * Input and output resistance can be modified as desired

Description : Compare small signal amplifier with power amplifier

Last Answer : Parameters Small signal Amplifiers Power Amplifiers Amplification quantity It increases voltage into high resistance load. Hence small signal amplifiers are also called as voltage amplifiers. It ... Coupling R-C coupling Transformer coupling Power output low High

Description : State the need and types of amplifier coupling. 

Last Answer : Need of amplifier coupling: 1.When ever large amplifier with very good impedance matching is required, a signal stage amplifier circuit will not able to amplify the signal to a large extent. 2 ... 2.Transformer coupled amplifier 3.Direct coupled amplifier 4. Inductance (LC) coupling

Description : Give the different types of amplifier coupling.

Last Answer : 1. Resistance – capacitance (RC) coupling.  2. Inductance (LC) coupling.  3. Transformer coupling (TC)  4. Direct coupling (D.C.)

Description : Draw circuit diagram of two stage RC coupled amplifier using BJT

Last Answer : BJT - To amplify input signal. R1 & R2 = Biasing resistor to provide DC biasing voltage RE = Emitter resistor to control gain RL = Load resistor to carry load current Cin = Cout = Coupling capacitors to block DC CE = emitter bypass resistor

Description : What is a BJT amplifier?

Last Answer : Bilpolar Juntion transistor , this fuction is control the current

Last Answer : Active region of BJT act as amplifier.

Description : What is Amplifier Coupling ?

Last Answer : Amplifier coupling is the process of connecting the output of one amplifier stage to the input of another amplifier stage to amplify the weak signal in phases. Couplings are used to gain more or less.

Description : In the illustrated circuit, one advantage of the capacitor coupling over direct coupling is ____________. EL-0048 A. as the frequency decreased the capacitive reactance (Xc) increases B. the amplifier becomes ... of the signal while it isolates the biasing of each stage. D. good frequency response.

Last Answer : Answer: C

Description : Which of the following methods cannot be used to increase the bandwidth for cascaded RF amplifier stages? A) Wave traps in each stage B) Stagger tuning C) A shunt damping resistor across each tuned circuit D) Doubled tuned transformers with tighter coupling

Last Answer : A) Wave traps in each stage

Description : In a resistance loaded, RC coupled amplifier the dc component is blocked by A) Load resistance RL B) Coupling capacitor, CC C) RB D) The transistor.

Last Answer : B) Coupling capacitor, CC

Description : The Bandwidth of an RC-coupled amplifier is limited by: A) coupling capacitors at the low frequency end and bypass capacitors at the high frequency end B) coupling capacitors at the high frequency ... at the low frequency end and bypass as well as coupling capacitors at the high frequency end.

Last Answer : C) bypass and coupling capacitors at the low frequency end and shunt capacitors at the high frequency end and

Description : What is the most common form of coupling for an rf amplifier?

Last Answer : Transformer coupling.

Description : If current gain is required from an rf amplifier, what type of component should be used as an output coupling element?

Last Answer : A step-down transformer.

Description : What type coupling would be most useful for an audio amplifier between the first and second stages?

Last Answer : RC coupling.

Description : What type coupling is usually used to couple the output from a power amplifier?

Last Answer : Transformer coupling.

Description : What are four methods of coupling amplifier stages?

Last Answer : Direct, RC, impedance, and transformer coupling.

Description : What is the purpose of an amplifier-coupling network?

Last Answer : To transfer energy (a signal) from one stage to another.

Description : Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Last Answer : Advantages: 1. It has a wide frequency response. 2. For coupling the resistor and the capacitor are used and which are not expensive so the cost is low. 3. The circuit is very ... a wide frequency band. 5. It is high fidelity amplifier. 6. It provides less frequency distortion.

Description : Transformer coupling is used in class A amplifier to make it : -  a) more efficient b) less bulky c) less costly d) distortion free

Last Answer : Transformer coupling is used in class A amplifier to make it : - more efficient

Description : The purpose of a coupling capacitor in an amplifier is to:  (1) Control the output (2) Provide impedance matching (3) Provide DC isolation between amplifier and load (4) W Increase the bandwidth

Last Answer : The purpose of a coupling capacitor in an amplifier is to: Provide DC isolation between amplifier and load.

Description : One advantage of transformer coupling in transistor amplifier is that:  (1) it provides excellent frequency response (2) It is simple and less expensive than others (3) Low power supply may be used (4) High efficiency and high power output is obtained.

Last Answer : One advantage of transformer coupling in transistor amplifier is that: High efficiency and high power output is obtained.

Last Answer : For an amplifier, the coupling method which gives the highest gain is Transformer coupling.

Description : List specification of BJT.

Last Answer : * The bipolar junction transistor (BJT) has small signal current gain, α (hfb). * Maximum collector current Ic (max). * Maximum collector to emitter voltage, VCE (max). * Collector to emitter ... . * Collector to emitter cut off voltage, VCEO. * Base emitter saturation voltage, VBE (sat).

Description : List configurations of BJT. 

Last Answer : Configurations of BJT : 1) Common Base (CB) configuration 2) Common Emitter (CE) configuration 3) Common Collector (CC) configuration

Description : Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Last Answer : Two advantages of voltage divider biasing of BJT. 1. It is very simple method of transistor biasing. 2. The biasing conditions can be very easily set. 3. there is no loading of ... 5. The resistor RE introduces a negative feedback. So all the advantages of negative feedback are obtained. 

Description : Draw Bootstrap sweep generator circuit. Compare Miller Integrator and bootstrap sweep generator with respect to the technique used.

Last Answer : Circuit diagram of bootstrap sweep generator: Miller Integrator Bootstrap sweep generator It is an integrator used to convert input step waveform into ramp waveform. In ... than Bootstrap sweep circuit The linearity of sweep voltage is poor than Miller integrator

Description : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Last Answer : Compare Class A ,Class B, Class C and class AB power amplifiers on the basis of: i)Angle of conduction ii)Efficiency iii)Position of operating pointing power dissipation iv)Distortion

Description : Explain the term crossover distortion. State methods to overcome it.

Last Answer : Explanation:-  * Cross over distortion occurs in Class B push pull Amplifier.  * In the push-pull configuration, the two identical transistors get into conduction, one after the other and the output ... transistors won t be OFF at the same time. The remedy is to use Class AB amplifier.

Description : Define : (i) Sweep time (ii) Retrace time

Last Answer : (i) Sweep time: It is defined as time interval taken by time based signal generator to increase from minimum to maximum voltage. (ii) Retrace time: It is defined as time taken by time based signal generator to decrease from maximum to minimum voltage.

Description : State classification of Amplifiers.

Last Answer : CLASSIFICATION OF AMPLIFIERS: A] Based on input signal 1. Small signal amplifiers 2. Large signal amplifiers B] Based on output signal 1. Voltage amplifier 2. Power amplifier C ... coupling 1. Direct coupled amplifiers 2. R-C Coupled amplifier 3. Transformer coupled amplifier

Description : Comment on the effect of negative feedback on the gain, input and output resistance of the feedback amplifiers.Describe the gain bandwidth product term used in this context and its importance.

Last Answer : Effect of negative feedback: 1. Gain decreases with negative feedback. 2. Input resistance increases with negative feedback. 3. Output resistance decreases with negative feedback. Explanation ... feedback bandwidth increases which means it is stable output on more range of frequency.

Description : Compare the fixed voltage regulators using 78XX and 79XX.

Last Answer : Compare the fixed voltage regulators using 78XX and 79XX.

Description : Compare between RC phase shift oscillator and crystal oscillator.

Last Answer : RC phase shift oscillator Crystal oscillator This oscillator is used for low frequency range. Quartz crystal is mainly used in radio-frequency (RF) oscillators Used resistor and capacitor ... RC network is used as feedback network. Crystal is connected in feedback.

Description : Justify the need of current time base generator to obtain the specified sawtooth waveform with one example.

Last Answer : Justification:- * Current Time base generator is a circuit where the output current is a linear function of time over a specified time interval. * Time base circuits are used by radar systems to determine ... the time. * The diode D does not conduct during the sweep, because it is reverse biased.

Description : Classify the power amplifiers on the basis of operation and input/output waveforms.

Last Answer : Depending upon the operation and input/output waveforms power amplifiers are classified into following type. 1) Class A amplifier. 2) Class B amplifier. 3) Class C amplifier. 4) Class AB amplifier. 5) Class D amplifier

Description : Name two types of BJT &draw their symbols. 

Last Answer : Two types of BJT: * NPN * PNP 

Description : List the types of power amplifier.

Last Answer : Types of Power amplifier: 1) Class A power amplifier 2) Class B power amplifier 3) Class AB power amplifier 4) Class C power amplifier

Description : State the need of multistage amplifier. List the types of multistage amplifier and give two advantages of each type. 

Last Answer : Need of multistage amplifier: The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, ... use more than one stage of amplification. Such an amplifier is called a MULTISTAGE AMPLIFIER .