State features of ADC 0808.

1 Answer

Answer :

1. Easy to interface with all Microprocessors or works Stand alone.

2. Eight channel 8-bit ADC module.

3. Can measure up to 8 Analog values.

4. On chip Clock not available, external Oscillator is needed (Clock).

5. Digital output various from 0 to 255, operating power is 15mW, conversion time 100us.

Related questions

Description : In ADC 0808 if _______ pin high enables output. a) EOC b) I/P0-I/P7 c) SOC d) OE

Last Answer : b) I/P0-I/P7

Description : State any four important features of 8051 microcontroller.

Last Answer : Features of 8051 microcontroller:  1) 8- bit data bus and 8- bit ALU. 2) 16- bit address bus - can access maximum 64KB of RAM and ROM. 3) On- chip RAM -128 bytes (Data ... 0 and Timer 1, two external hardware interrupts- INT0 and INT1, Serial communication interrupt for both receive and transmit.

Description : State and explain the need of the following development tools microcontroller board: (i) Editor (ii) Assembler (iii) Compiler (iv) Linker

Last Answer : 1) Editor: An editor is a program which helps you to construct your assembly language program in right format so that the assembler will translate it correctly to machine language. So, you can type your ... . Some examples of linker are ASEM-51 BL51, Keil u Vision Debugger, LX 51 Enhanced Linker etc

Description : State the alternate pin functions of port 3 of 8051.

Last Answer :  the alternate pin functions of port 3 of 8051 :

Description : Draw interfacing of 16 × 2 LCD with 8051 and state the function of EN and RS of LCD

Last Answer : Diagram: RS: RS is the register select pin. We need to set it to 1, if we are sending some data to be displayed on LCD. And we will set it to 0 if we are sending some command instructions ... the LCD to latch in the data present at the data pins. This pulse must be a minimum of 450ns wide.

Description : State the advantages of dual slope ADC

Last Answer :  It provides excellent noise rejection of ac signals whose periods are integral multiples of the integration time T. It is defined as the total time required to convert an analog signal into its ... output. It depends on the conversion technique used & the propagation delay of circuit components.

Description : State important specification parameters of ADC

Last Answer : Accuracy Resolution Linearity Conversion time Settling time stability

Description : Explain the following instructions. SWAP A ADD C MUL AB CJNE A, add, radd MOV A, R0 MOVX A, @ A + DPTR.

Last Answer : SWAP A Description: This instruction exchanges bits 0-3 of the Accumulator with bits 4-7 of the Accumulator. This instruction is identical to executing "RR A" or "RL A four times ... referred to as the base address and the accumulator value is referred to as the index address.

Description : Explain the various selection factors of microcontroller suitable for application.

Last Answer : The selection of microcontroller depends upon the type of application. The following factors must be considered while selecting the microcontroller.  1. Word length: The word length of ... and for lesser production EPROM version or CPU version with external program memory is suitable

Description : Draw the format of PSW register of 8051 microcontroller and explain the function of each bit.

Last Answer : 1. CY: Carry flag. This flag is set whenever there is a carry out from the D7 bit after an 8 bit addition or subtraction. It can also be set to 1 or 0 directly by instructions such as SETB C and ... the A register contains an odd number of 1s, then P=1. P=0 if A has an even number of 1s.

Description : Describe power down mode and ideal mode of 8051 with circuit diagram . which SFR is used to set these modes and draw the same.

Last Answer : IDLE MODE In the Idle mode, the internal clock signal is gated off to the CPU, but not to the Interrupt, Timer and Serial Port functions. The CPU status is preserved in its entirety, the Stack Pointer, ... t change on chip RAM PCON (Power Control Register) SFR is used to set these modes.

Description : Define the term BUS related to microprocessor/controller and list different buses used in microcontroller.

Last Answer : BUS: A Bus is a set of physical connections used for communication between CPU and peripherals. Different buses used in microcontroller are: 1. Address Bus 2. Data Bus 3. Control Bus

Description : Draw the format of SCON register.

Last Answer : SM0 SCON.7 Serial port mode specifier SM1 SCON.6 Serial port mode specifier SM2 SCON.5 Used for multiprocessor communication (Make it 0.) REN SCON.4 Set/ cleared by software to enable/ ... flag. Set by hardware halfway through the stop bit time in mode 1. Must be cleared by software.

Description : List out any two instructions of following addressing modes: (i) Immediate addressing. (ii) Register addressing.

Last Answer : (i) Immediate addressing instructions: 1. MOV A, #36H 2. MOV DPTR, #27A2H (ii) Register addressing. 1. MOV A, R0 2. MOV R7, A

Description : Find out the number of address lines required to access 4 KB of RAM

Last Answer : 12 address lines required to access 4 KB of RAM as  212 = 4KB 

Description : Draw and explain Internal port structure of Port 0 and Port 1 of 8051 microcontroller.

Last Answer : Port-0 can be configured as a normal bidirectional I/O port or it can be used for address/data interfacing for accessing external memory. When control is '1', the port is used for address/data ... is not able to sink the current the pin voltage may rise, leading to a possible wrong reading.

Description : Describe with sketches the procedure to troubleshoot the traffic light controller.

Last Answer : Considerations of Traffic Signal  1) Traffic light may have sensors integrated to provide real time traffic information  2) Based on the traffic information provided by the sensor, the duration of the ... 8) Capacity analysis of the intersection for current and future years using growth

Description : Differentiate between (i) Harvard and Von-neuman architecture (ii) Microprocessor and Microcontroller

Last Answer : i) Harvard Architecture and Von-neuman architecture ii) Microprocessor and Microcontroller

Description : Explain with sketch the interfacing of 4 ×4 matrix keypad with 8051 microcontroller.

Last Answer : Interfacing keypad Fig. shows how to interface the 4 X 4 matrix keypad to two ports in microcontroller. The rows are connected to an output port and the columns are connected to an input port. To ... key has been pressed, the next task is to find out which column the pressed key belongs to.

Description : Explain the use of following assembler directives. (i) EQU (ii) ORG

Last Answer : (i) EQU: Equate It is used to define constant without occupying a memory location. Syntax: Label EQU Numeric value By means of this directive, a numeric value is replaced by a symbol. For e.g. ... decimal. If the number is notfollowed by H, it is decimal and the assembler will convert it to hex.

Description : Describe serial communication in 8051. Explain the use of SCON register.

Last Answer : 8051 micro controller communicate with another peripheral device through RXD and TXD pin of port3.controller have four mode of serial communication.  1. Serial Data Mode-0 (Baud Rate Fixed) In this mode ... .0 Receive interrupt flag. Set by hardware halfway through the stop bit time in mode 1. 

Description : Draw the format of TCON register of 8051 and describe the function of each bit of it.

Last Answer : TCON: TIMER/COUNTER CONTROL REGISTER.BIT ADDRESSABLE  TF1 TCON. 7 Timer 1 overflows flag. Set by hardware when the Timer/Counter 1 Overflows. Cleared by hardware as processor ... 0 type control bit. Set/cleared by software to Specify falling edge/low level triggered External Interrupt

Description : Explain following instructions of 8051. (i) ADDC (ii) L CALL

Last Answer : (i) ADDC: The ADDC instruction adds a byte value and the value of the carry flag to the accumulator. The results of the addition are stored back in the accumulator. Several of the flag ... . Then the program counter is loaded with the new address and control is transferred to the subroutine. 

Description : Explain processes of interrupt enabling and disabling in 8051.

Last Answer : Interrupts are the events that temporarily suspend the main program, pass the control to the external sources and execute their task. It then passes the control to the main program where it had left off. ... interrupts. Its bit sequence and their meanings are shown in the following figure.

Description : Develop Assembly Language program (ALP) to find the largest number in a block of 10 numbers stored at location 40H onwards in internal RAM.

Last Answer : ORG 0000H MOV R1, #0AH ; Initialize Byte Counter MOV R0, #40H ; Initialize source pointer R0 to 40H DEC R1 ; decrement counter by one MOV 60H, @R0 ;Read First Byte UP: INC R0 ; Increment the ... MOV A,B MOV 50H, A ; store result at memory location 50H(Assume any location) HERE: SJMP HERE

Description : Explain function of following pins of 8051 (i) Pin 31 (ii) Pin 29 (iii) Pin 21-28 

Last Answer : i) Pin 31-EA : It is and active low I/P to 8051 microcontroller. When (EA)= 0, then 8051 microcontroller access from external program memory (ROM) only. When (EA) = 1, then it access internal ... /Output, when external memory is interfaced, PORT 2 pins act as the higher-order address bus. (A8-A15)

Description : Describe 8051 microcontroller as boolean processor.

Last Answer : * 8051 processor is a CPU that can perform some operation on a data and gives the output. * The 8051 processor contains a complete Boolean processor for single-bit operations. * The internal RAM contains 128 ... CLR C means clear the carry bit SETB 20h means set the memory bit with bit address 20h.

Description : Draw and explain the interfacing of DAC to 8051.

Last Answer : Diagram:  * Microcontroller generates output which is in digital form but many controlling system requires analog signal as they don't accept digital data thus making it necessary to use DAC ... current. Hence we require an I to V converter to convert this current into equivalent voltage. 

Description : List SFR in 8051.

Last Answer : ACC and B registers - 8 bit each DPTR : [DPH:DPL] - 16 bit combined PC : Program Counter - 16 bits Stack pointer SP - 8 bit PSW : Program Status Word Port Latches ... , serial control Timer Registers (TCON,TMOD,TL0/1,TH0/1) Power control Interrupt Enable, Interrupt Priority

Description : List specifications of 8051 microcontroller.

Last Answer : 1) 8- bit data bus and 8- bit ALU. 2) 16- bit address bus - can access maximum 64KB of RAM and ROM. 3) On- chip RAM -128 bytes (Data Memory) 4) On- chip ROM - 4 KB ( ... 0592 MHz 9) Has power down and idle mode in microcontroller when no operation is performed. 10) Six interrupts are available.

Description : What is an Analog-to-Digital Converter (ADC) in Arduino?

Last Answer : An Analog-to-Digital Converter (ADC) in Arduino is a component that converts analog signals, such as temperature or light, into digital signals that can be processed by the microcontroller.

Description : ABC and ADC are two right triangles with common hypotenuse AC. Prove that angle CAD = angle CAB -Maths 9th

Last Answer : Given, AC is the common hypotenuse. ∠B = ∠D = 90°. To prove, ∠CAD = ∠CBD Proof: Since, ∠ABC and ∠ADC are 90°. These angles are in the semi circle. Thus, both the triangles are lying in the semi ... D are concyclic. Thus, CD is the chord. ⇒ ∠CAD = ∠CBD (Angles in the same segment of the circle)

Description : ABC and ADC are two right triangles with common hypotenuse AC. Prove that angle CAD = angle CAB -Maths 9th

Last Answer : Given, AC is the common hypotenuse. ∠B = ∠D = 90°. To prove, ∠CAD = ∠CBD Proof: Since, ∠ABC and ∠ADC are 90°. These angles are in the semi circle. Thus, both the triangles are lying in the semi ... D are concyclic. Thus, CD is the chord. ⇒ ∠CAD = ∠CBD (Angles in the same segment of the circle)

Description : In the figure, find teh perimeter of the shaded region where. ADC, AEB and BFC are semi-circles on diameters AC, AB and BC respectively. -Maths 10th

Last Answer : Given: Diameter of semicircle AEB= 2.8 cm RADIUS OF SEMICIRCLE(AEB)= 2.8/2= 1.4 cm Diameter of semicircle BFC=1.4 cm RADIUS OF SEMICIRCLE(BFC)= 1.4/2= 0.7 cm Diameter of semicircle ADC= 2.8+1.4 = ... ; .6 = 13.2 cm Hence, the perimeter of the shaded region is 13.2 cm HOPE THIS WILL HELP YOU...

Description : What is the full form of ADC ?

Last Answer : The full form of ADC is Aeitional Deputy Commissioner.

Description : In the above figure, O is the centre of the circle AB,AD and CD are the chords . If `/_ ADC=130^(@)` then fid `/_ ACB`.

Last Answer : In the above figure, O is the centre of the circle AB,AD and CD are the chords . If `/_ ADC=130^(@)` then fid `/_ ACB`.

Description : Which is the fastest ADC and why?

Last Answer : Simultaneous type A/D converter(flash type A/D converter) is the fastest because A/D conversion is performed simultaneously through a set of comparators 

Description : What is the main drawback of a dual-slop ADC?

Last Answer : The dual slope ADC has long conversion time. This is the main drawback of dual slope ADC

Description : Explain in brief the principle of operation of successive Approximation ADC.

Last Answer : The circuit of successive approximation ADC consists of a successive approximation register (SAR), to find the required value of each bit by trial & error.With the arrival of START command, SAR sets the MSB ... /P signal. This O/P is low or High. This process continues until all bits are checked.

Description : A ______ is a combination load balancer and application server that is a server placed between a firewall or router. a) ABC b) ACD c) ADC d) All of the mentioned

Last Answer : ADC

Description : A ______ is a combination load balancer and application server that is a server placed between a firewall or router. a) ABC b) ACD c) ADC d) All of the mentioned

Last Answer : ADC

Description : . A ______ is a combination load balancer and application server that is a server placed between a firewall or router. a) ABC b) ACD c) ADC d) All of the mentioned

Last Answer : ADC

Description : What is the result if the input of ADC is changing while performing conversion? A

Last Answer : Aperture distortion

Description : Resolution of ADC is defined as a) 1/ (2N – 1) b) 2N-1 c) 1/ (2N-1) d) 2N-1

Last Answer : b) 2N-1

Description : What are the commonest congenitally missing teeth:VERY CONTROVERSIAL BUT SEE THE SAMPLE QUESTIONS FROM ADC IT’S THE ANSWER A. 12, 22 B. 35, 45 ACC TO CAMERON C. 15, 25 D. 33, 43

Last Answer : A. 12, 22

Description : Which one of the following is true about oral hairy leukoplakia?** ADC M07 A. Associated with HIV virus infection and is commonly seen on the dorsal of the tongue B. Associated with HIV ... Always associated with trauma to the lateral side of the tongue E. Always associated with pernicious anaemia

Last Answer : B. Associated with HIV virus infection and is commonly seen on the lateral side of the tongue C. Usually caused by Candida species

Description : As far as surgical removal of wisdom teeth is concerned, which of the following is true?**CHECK A. Prophylactic prescription of antibiotic reduces dramatically the chances of infection B. Raising ... root E. The use of vasoconstrictors in local anaesthetics will increase the chances of infection.

Last Answer : C. Prophylactic prescription of dexamethasone will dramatically reduces post operative swelling

Description : Loss of sensation in the lower lip may be produced by,CHECK ADC M07 A. Bell’s palsy B. Traumatic bone cyst C. Trigeminal neuralgia D. Fracture in the mandible first molar region E. Ludwig’s angina

Last Answer : D. Fracture in the mandible first molar region E. Ludwig’s angina

Description : Before filling a class V abrasion cavity with GIC you should(+adc March07) A. Clean with pumice, rubber cup, water and weak acid B. Dry the cavity thoroughly before doing anything C. Acid itch cavity then dry thoroughly

Last Answer : A. Clean with pumice, rubber cup, water and weak acid

Description : Define ADC and DAC. Write two applications of each.

Last Answer : ADC An analog to digital converter (ADC), converts any analog signal into quantifiable data, which makes it easier to process and store, as well as more accurate and reliable by ... signal, hence any analog circuit can work with digital system Application - Microcontroller, washing machine