Name two types of BJT &draw their symbols.

Name two types of BJT &draw their symbols. 
by

1 Answer

Answer :

Two types of BJT:

* NPN

* PNP 

image

by

Related questions

State 2 advantages of JFET over BJT.

Description : State 2 advantages of JFET over BJT.

Last Answer : Advantages of JFET over BJT: 1) High input impedance 2) Better thermal stability 3) Produce less noise 4) Smaller than BJT 5) Rugged in construction and simpler to fabricate 6) High degree of isolation between Input and Output. 

List the types of power amplifier.

Description : List the types of power amplifier.

Last Answer : Types of Power amplifier: 1) Class A power amplifier 2) Class B power amplifier 3) Class AB power amplifier 4) Class C power amplifier

State the need and types of amplifier coupling.

Description : State the need and types of amplifier coupling. 

Last Answer : Need of amplifier coupling: 1.When ever large amplifier with very good impedance matching is required, a signal stage amplifier circuit will not able to amplify the signal to a large extent. 2 ... 2.Transformer coupled amplifier 3.Direct coupled amplifier 4. Inductance (LC) coupling

List the types of coupling used in BJT amplifier.

Description : List the types of coupling used in BJT amplifier. 

Last Answer : Types of coupling used in BJT amplifier: i. Resistance capacitance (RC)coupling ii. Impedance coupling iii. Transformer coupling iv. Direct coupling

Explain the operating principle of PNP transistor.

Description : Explain the operating principle of PNP transistor. 

Last Answer : The circuit connection of PNP transistor with supply voltages is as shown above. The emitter-base junction is connected as forward bias. Due to this the emitter pushes the holes from the P ... by the collector. This develops the collector current IC. This is how a PNP transistor operates. 

Define intrinsic standoff ratio.

Description : Define intrinsic standoff ratio.

Last Answer : It is defined as the ratio of the RB1 (base resistance 1) to the inter-base resistance RBB. 

Sketch the single tuned amplifier.

Description : Sketch the single tuned amplifier.

Last Answer : single tuned amplifier

Which type of MOSFET is called Normally ON MOSFET”? Why?

Description : Which type of MOSFET is called Normally ON MOSFET”? Why? 

Last Answer : DMOSFET is called Normally ON MOSFET. In DMOSFET already channel is present and at Vgs = 0v, drain current Id=Idss i.e. drain to source saturation current is flowing. 

Define gain and bandwidth.

Description : Define gain and bandwidth. 

Last Answer : Gain: It is the ratio of output quantity to the input quantity. Bandwidth: It is defined as the range (band) of frequency over which the gain is constant.  (Or) It is the range of frequency over which the gain is greater than 70.7% of the maximum gain possible

State any four applications of transistor.

Description : State any four applications of transistor.

Last Answer : Amplifier

Draw the characteristics of UJT and state its working principle.

Description : Draw the characteristics of UJT and state its working principle.

Last Answer : The characteristics of Unijunction Transistor (UJT) can be explained by three parameters: * Cutoff Region * Negative Resistance Region * Saturation Region Cutoff Region : The ... in its ON position. The emitter voltage VE remains almost constant with the increasing emitter current.

Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Description : Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Last Answer : Frequency of oscillation is given by,

Draw the circuit of single tuned amplifier and state its operating principle.

Description : Draw the circuit of single tuned amplifier and state its operating principle.

Last Answer : Operating Principle: The working of tuned voltage amplifier may be understood by considering a radio frequency signal, to be amplified applied at the input of the amplifier. The resonant frequency ... will be amplified. And all the other frequencies will be rejected by the tuned circuit. 

State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Description : State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Last Answer : Basic Principle: The main principle of a piezoelectric crystal is that a mechanical force, when applied on the crystal, it vibrates and produces electric charges on the crystal surface. When ac voltage is applied across crystal, it vibrates at the frequency of the applied voltage. (OR)

State and explain the working principle of FET amplifier and list its applications.

Description : State and explain the working principle of FET amplifier and list its applications.

Last Answer : Operation of FET amplifier: When small a.c. signal is applied to the gate, it produces variation in the gate to source voltage. This results in variation in the drain current. As ... input voltage.  Application: Buffer amplifier Low noise amplifier Cascade amplifier Chopper amplifier

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Description : Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Last Answer : Circuit diagram:- Input / Output waveforms:-

Draw the input and output characteristics of CE configuration.

Description : Draw the input and output characteristics of CE configuration.

Last Answer : Input characteristics of CE configuration: Output characteristics of CE configuration:

Draw the circuit diagram of Bootstrap’s time base generator and explain its working.

Description : Draw the circuit diagram of Bootstrap’s time base generator and explain its working.

Last Answer : Circuit Diagram Waveform: Here transistor Q1 acts as a switch and transistor Q2 acts as an emitter follower (i.e. a unit gain amplifier).  Circuit Operation: Initially transistor ... The circuit pulls itself up by its own bootstrap and hence it is known as bootstrap sweep circuit. 

Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Description : Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Last Answer : Parameter Class A Class B 

Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Description : Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Last Answer : Diagram of complementary symmetry Class B push-pull amplifier: Working: The above circuit employs a NPN transistor and a PNP transistor connected in push pull configuration. When the input ... of class B, this circuit is termed as Complementary symmetry push pull class B amplifier.

Draw the construction of p-channel D-MOSFET and state its working principle.

Description : Draw the construction of p-channel D-MOSFET and state its working principle. 

Last Answer : Construction of p-channel D-MOSFET: Working principle: The gate to source voltage is set to zero volts by the direct connection from one terminal to the other & voltage VDS is applied ... The value of voltage of VGS at which drain current nearly becomes zero is called cut off voltage. 

Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Description : Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Last Answer : Advantages: 1. It has a wide frequency response. 2. For coupling the resistor and the capacitor are used and which are not expensive so the cost is low. 3. The circuit is very ... a wide frequency band. 5. It is high fidelity amplifier. 6. It provides less frequency distortion.

Draw the drain characteristics of p-channel FET and explain.

Description : Draw the drain characteristics of p-channel FET and explain.

Last Answer : Drain characteristics:- As VDS is increased from zero as shown , ID will increased proportionally through the p channel. In this region the channel resistance is constants because the depletion region is ... the depletion layer. (i.e. channel width zero) is called cutoff voltage or VGS(off).

Draw the frequency response of DC amplifier. Comment on it.

Description : Draw the frequency response of DC amplifier. Comment on it.

Last Answer : frequency response: Comment : The gain remains constant at its midband value AM down to zero frequency (DC). Directcoupled amplifiers do not suffer gain reduction at low frequencies as compared ... , gain falls off at the high frequency end due to the internal capacitances of the transistor.

Draw the circuit and explain the operation of UJT relaxation oscillator.

Description : Draw the circuit and explain the operation of UJT relaxation oscillator. 

Last Answer : Working: When the supply voltage (VCC) is switched ON, the capacitor charges through resistor (R), till the capacitor voltage reaches the voltage level (VP) which is called as peak point voltage. At ... resistor R is shown as a variable resistor. The sweep period is given by the relation

Draw the transfer characteristics for N-channel JFET.

Description : Draw the transfer characteristics for N-channel JFET.

Last Answer : Transfer characteristics for N-channel JFET: 

Define the following terms: (i) Stabilization (ii) Thermal runaway

Description : Define the following terms: (i) Stabilization (ii) Thermal runaway

Last Answer : Stabilization: The process of making operating point independent of temperature changes or variation in transistor parameter is known as stabilization. The maintenance of the operating point stable is called the ... happens, the device gets burnt out. This process is known as Thermal Runaway .

State the need of biasing and describe the concept of DC load line

Description : State the need of biasing and describe the concept of DC load line

Last Answer : Need of Biasing for Transistor: The transistor should be biased in the active region if it is to be used for amplification and in saturation and cut off if it is used as a switch. 2. The Q ... The position of operating point on the load line is dependent on the application of the transistor.

State the need of regulation. Explain the concept of load & line regulation.

Description : State the need of regulation. Explain the concept of load & line regulation.

Last Answer : Need of Regulation: The major disadvantage of a power supply is that the output voltage changes with the variations in the input voltage or the DC output voltage of the rectifier also increase similarly. In ... the change in output voltage that will occur per unit change in the input voltage. 

State the working principle of UJT

Description : State the working principle of UJT

Last Answer : Figure shows the equivalent circuit of a unijunction transistor with voltage source VEE connected across emitter and base 1 and VBB connected across base 1 and base 2. Hence the Emitter diode is reversed ... emitter current begins to flow ,the UJT is said to be fired, triggered or turned on.

Sketch p-channel JFET construction.

Description : Sketch p-channel JFET construction.

Last Answer : p- channel JFET constructional diagram:

List applications of power amplifier.

Description : List applications of power amplifier.

Last Answer : Below are the applications of power amplifiers across different sectors: 1.Consumer Electronics: Audio power amplifiers are used in almost all consumer electronic devices ranging from microwave ovens, ... data transfer rates and usability. They are also used in satellite communication equipment.

Draw symbol for n-channel and p-channel MOSFET.

Description : Draw symbol for n-channel and p-channel MOSFET.

Last Answer : Symbol n-channel and p-channel MOSFET :   OR  

Define Q-point

Description : Define Q-point 

Last Answer : Q-point: For proper operation of transistor, in any application, we set fixed levels of certain voltages and currents in a transistor. These values of currents and voltages define the point, at which ... . This point is called operating point. It is also known as quiescent point or Q point.

What are different types of quantum numbers , write them with their symbols ?

Description : What are different types of quantum numbers , write them with their symbols ?

Last Answer : Ans. 1.Principal Quantum Numbers (n) 2.Azimuthal Quantum Numbers(l) 3.Magnetic Quantum Numbers (m) 4.Spin Quantum Numbers(s)

Explain different types of attribute with example and their symbols used in ER diagram.

Description : Explain different types of attribute with example and their symbols used in ER diagram.

Last Answer : Different types of attributes are: 1. Simple attribute: A simple attributes are those which cannot be subdivided. Eg:Rollno-  symbol 2. Composite attribute: a composite attribute is ... value can be calculated or determined from another attribute Eg: age from dateofbirth  Symbol

Draw circuit diagram of two stage RC coupled amplifier using BJT

Description : Draw circuit diagram of two stage RC coupled amplifier using BJT

Last Answer : BJT - To amplify input signal. R1 & R2 = Biasing resistor to provide DC biasing voltage RE = Emitter resistor to control gain RL = Load resistor to carry load current Cin = Cout = Coupling capacitors to block DC CE = emitter bypass resistor

Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Description : Draw circuit diagram of voltage divider biasing list two advantages of voltage divider biasing of BJT.

Last Answer : Two advantages of voltage divider biasing of BJT. 1. It is very simple method of transistor biasing. 2. The biasing conditions can be very easily set. 3. there is no loading of ... 5. The resistor RE introduces a negative feedback. So all the advantages of negative feedback are obtained. 

The seven segment arrangement for numerical display on consoles, test meters and other applications can be either ________________. A. UJT or BJT B. BCD or OCD C. JFET or IGFET D. LED or LCD

Description : The seven segment arrangement for numerical display on consoles, test meters and other applications can be either ________________. A. UJT or BJT B. BCD or OCD C. JFET or IGFET D. LED or LCD

Last Answer : Answer: D

Power BJT is a current controlled device. Why?

Description : Power BJT is a current controlled device. Why?

Last Answer : Because the output (collector) current can be controlled by base current.

why the bjt is known as current controlled device and fet is known as voltage controlled device ?

Description : why the bjt is known as current controlled device and fet is known as voltage controlled device ?

Last Answer : Ans- 1. In BJT because of the current the output will vary. 2. Where as in FET by means of Voltage the output is varied.

Which is the most suitable power device for high frequency ( more 100 kHz) switching application? a) Power MOSFET b) BJT c) SCR d) UJT

Description : Which is the most suitable power device for high frequency ( more 100 kHz) switching application? a) Power MOSFET b) BJT c) SCR d) UJT

Last Answer : Ans: Power MOSFET

A modern power semiconductor device IGBT is combines the characteristics of a) BJT and MOSFET b) FCT and GTO c) SCR and MOSFET d) SCR and BJT

Description : A modern power semiconductor device IGBT is combines the characteristics of a) BJT and MOSFET b) FCT and GTO c) SCR and MOSFET d) SCR and BJT

Last Answer : Ans: BJT and MOSFET

Draw the output characteristics of BJT in CE configuration and label various regions on it.

Description : Draw the output characteristics of BJT in CE configuration and label various regions on it.

Last Answer :  output characteristics of BJT in CE configuration 

State the applications of BJT.

Description : State the applications of BJT.

Last Answer : Applications of BJT: 1. As a switch 2. As an amplifier 3. As a multivibrator 4. As a oscillator 5. As a timer circuit 6. As a Logic circuits 7. Delay circuits

Draw the construction of BJT (NPN) and explain its working principle. State and explain different operating regions.

Description : Draw the construction of BJT (NPN) and explain its working principle. State and explain different operating regions.

Last Answer : Construction of BJT (NPN): Working of NPN Transistor : The circuit diagram of the NPN transistor is shown in the figure below. The forward biased is applied across the emitter-base ... Zero with input current is Zero transistor in cut off. In this region transistor act as open switch

Define the following with respect to BJT. (i) Input resistance (ii) Output resistance

Description : Define the following with respect to BJT. (i) Input resistance (ii) Output resistance

Last Answer : Input resistance: It is the ratio of small change in emitter -to-base voltage(∆VEB) to the resulting change in emitter current (∆IE) for a constant collector to base voltage(VCB) ... of BJT is ratio of voltage between output terminal and common terminal to current through output terminal. 

Comparison of three configuration of BJT

Description : Comparison of three configuration of BJT

Last Answer : Parameter Common Base(CB) Common Emitter (CE) Common collector (CC) Input terminal  Emitter Base Base Common terminal Base Emitter Collector Output terminal Collector Collector Emitter Gain factor Alpha(Ic/Ie) Beta(Ic/Ib) Gamma(Ie/Ib)

Comparison of BJT and FET

Description : Comparison of BJT and FET

Last Answer : FET BJT It is unipolar device i.e. current in the device is carried either by electrons or holes It is bipolar device i.e. current in the device is carried either by both ... is comparatively more noisy. It is relatively immune to radiation. It is susceptible to radiation

Draw symbol of NPN transistor and state three configurations of transistor (BJT)

Description : Draw symbol of NPN transistor and state three configurations of transistor (BJT)

Last Answer : Configuration - Common Emitter Common Collector Common Base