Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.

Draw the single stage class A power amplifier circuit diagram and draw the input and output waveforms.
by

1 Answer

Answer :

Circuit diagram:-

image

Input / Output waveforms:-

image

by

Related questions

Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Description : Draw the circuit diagram of complementary symmetry Class B push-pull amplifier and describe its working.

Last Answer : Diagram of complementary symmetry Class B push-pull amplifier: Working: The above circuit employs a NPN transistor and a PNP transistor connected in push pull configuration. When the input ... of class B, this circuit is termed as Complementary symmetry push pull class B amplifier.

Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Description : Draw and describe circuit diagram of centre tapped rectifier with LC filter along with its input and output waveforms.

Last Answer : Explanation: A centre- tap full wave rectifier drive produces the rectified voltage and it drives the LC filter. We know that the series inductor filter is preferred for low values of load resistance ( ... load RL. The output voltage waveforms are similar to that as shown in figure above.  

Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier

Description : Define rectifier. Draw circuit diagram and input-output waveforms of bridge type full wave rectifier 

Last Answer : Rectifier - This circuit convert AC signal into DC.

Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms.

Description : Explain Center-tapped full wave rectifier with the help of circuit diagram and draw input output waveforms. 

Last Answer : Operation : During positive half cycle of an AC supply, D1 will forward biased and current starts flowing through load. The output voltage is equal to +Vs. During negative half cycle of an AC ... output voltage is equal to +Vs. In this pulsating DC waveform will be obtained at the load. 

Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Description : Draw the multistage amplifier circuit diagram using RC coupling. State its advantages.

Last Answer : Advantages: 1. It has a wide frequency response. 2. For coupling the resistor and the capacitor are used and which are not expensive so the cost is low. 3. The circuit is very ... a wide frequency band. 5. It is high fidelity amplifier. 6. It provides less frequency distortion.

Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Description : Explain the operation of a full wave bridge rectifier with π filter using a neat diagram. Draw input and output waveforms.

Last Answer : During positive half-cycle of input, the secondary voltage VAB is positive, so diodes D1 and D2 forward biased and D3 and D4 reverse biased. The load current flows from terminal A ... smooth DC voltage appears across the load. The input and output waveforms are shown in the figure.

Draw the circuit of single tuned amplifier and state its operating principle.

Description : Draw the circuit of single tuned amplifier and state its operating principle.

Last Answer : Operating Principle: The working of tuned voltage amplifier may be understood by considering a radio frequency signal, to be amplified applied at the input of the amplifier. The resonant frequency ... will be amplified. And all the other frequencies will be rejected by the tuned circuit. 

Draw the practical AM diode detector circuit. Sketch its input and output waveforms.

Description : Draw the practical AM diode detector circuit. Sketch its input and output waveforms. 

Last Answer : Practical AM diode detector 1. Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wave of fixed frequency ... had taken place from a surface located at a greater height, called Virtual height of this layer.

Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it.

Description : Draw single phase full wave mid-point converter for inductive load. Draw input and output waveforms for it. 

Last Answer : Circuit Diagram: Waveforms:

The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an autotransformer B. operational amplifier whose output controls a step-up voltage reactor C. amplitude modulator whose output drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Description : Draw the block diagram of regulated power supply, explain function of each block and draw waveforms of each stage.

Last Answer : 1. A step down transformer 2. A rectifier 3. A filter 4. A regulator Operation of Regulated Power Supply:- Step Down Transformer:- A step down transformer will ... regulator. A regulator will maintain the output constant even when changes at the input or any other changes occur.

Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Description : Basic operating characteristics of the operational amplifier such as gain and stability are the function of its _____________. A. differential input stage B. power output stage C. feedback circuit D. supply voltages

Last Answer : Answer: C

Draw the input and output characteristics of CE configuration.

Description : Draw the input and output characteristics of CE configuration.

Last Answer : Input characteristics of CE configuration: Output characteristics of CE configuration:

Draw & describe working of bridge rectifier with its input output waveforms

Description : Draw & describe working of bridge rectifier with its input output waveforms

Last Answer : Four diodes are used. a)In positive half cycle Diodes D1 & D3 becomes forward biased they will conduct & current flows at that time D2 and D4 are reverse biased they will not ... at that time D1 and D3 are reverse biased they will not conduct. we get full cycle rectification.

Draw and describe working of series biased clipper with input output waveforms.

Description : Draw and describe working of series biased clipper with input output waveforms. 

Last Answer : Biased series positive clipper: Clipping of the signal takes place as soon as the input signal goes positive. If we want to change/adjust the clipping level of AC voltage, then external biasing voltage must be ... voltage must be used. The figure given below shows a biased (series) clipper.    

Draw circuit diagram of two stage RC coupled amplifier using BJT

Description : Draw circuit diagram of two stage RC coupled amplifier using BJT

Last Answer : BJT - To amplify input signal. R1 & R2 = Biasing resistor to provide DC biasing voltage RE = Emitter resistor to control gain RL = Load resistor to carry load current Cin = Cout = Coupling capacitors to block DC CE = emitter bypass resistor

State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Description : State the need of cascade amplifier and draw circuit diagram of 2-stage direct coupled amplifier.

Last Answer : Need:- The voltage (or power) gain, obtained from a single stage small signal amplifier, is limited. Therefore, it is not sufficient for all practical applications. Therefore, in order to obtain greater voltage and power gain, cascade amplifiers are used.

State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Description : State the basic principle of piezoelectric crystal and draw the circuit diagram of crystal oscillator.

Last Answer : Basic Principle: The main principle of a piezoelectric crystal is that a mechanical force, when applied on the crystal, it vibrates and produces electric charges on the crystal surface. When ac voltage is applied across crystal, it vibrates at the frequency of the applied voltage. (OR)

Draw the circuit diagram of Bootstrap’s time base generator and explain its working.

Description : Draw the circuit diagram of Bootstrap’s time base generator and explain its working.

Last Answer : Circuit Diagram Waveform: Here transistor Q1 acts as a switch and transistor Q2 acts as an emitter follower (i.e. a unit gain amplifier).  Circuit Operation: Initially transistor ... The circuit pulls itself up by its own bootstrap and hence it is known as bootstrap sweep circuit. 

Draw the circuit diagram of class AB power amplifier and describe its working.

Description : Draw the circuit diagram of class AB power amplifier and describe its working.

Last Answer : Circuit diagram: Circuit Description: The circuit consists of two center-tapped transformers T1 and T2, two identical transistors Q1 and Q2 , Resistor R and diode D. The DC voltage ... and Q2 conduct, as soon as input cross zero, negative sinusoidal voltage will appear across load.

Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms.

Description : Draw the circuit diagram and describe the working principle of full wave bridge rectifier. Draw its waveforms. 

Last Answer : During the first half cycle : During the first half cycle of the input voltage, the upper end of the transformer secondary winding is positive with respect to the lower end. Thus during the first ... , terminal D, diode D4, and terminal A back to transformer and output will positive half cycle.

Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Description : Draw circuit diagram and waveforms for centre-tap full wave rectifier.

Last Answer : Circuit Diagram:    

Draw circuit diagram for π filter and explain its working with waveforms.

Description : Draw circuit diagram for π filter and explain its working with waveforms.

Last Answer : Working of a Pi filter: In this circuit, we have a capacitor in parallel, then an inductor in series, followed by another capacitor in parallel. Capacitor C1 − This filter capacitor ... any ac component present in the signal to pass through it, which the inductor has failed to block.

Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Description : Compare between class A and class B amplifier on the basis of (i) Efficiency (ii) Power (iii) Position of Q- point (iv) O/P distortion

Last Answer : Parameter Class A Class B 

Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Description : Draw the single stage RC coupled amplifier circuit and explain its’s operation.

Last Answer : Operation:- The capacitors C1 and C2 are called as the coupling capacitors. As the load resistor RL (not shown in the diagram) is coupled to the amplifier through the coupling capacitor ... connected in the common emitter (CE) configuration. Therefore, this amplifier is called CE amplifier. 

Draw the frequency response of DC amplifier. Comment on it.

Description : Draw the frequency response of DC amplifier. Comment on it.

Last Answer : frequency response: Comment : The gain remains constant at its midband value AM down to zero frequency (DC). Directcoupled amplifiers do not suffer gain reduction at low frequencies as compared ... , gain falls off at the high frequency end due to the internal capacitances of the transistor.

For a class D commutation, answer the following: i) Explain the operation with circuit diagram. ii) Interpret with waveforms.

Description : For a class D commutation, answer the following: i) Explain the operation with circuit diagram. ii) Interpret with waveforms.

Last Answer : Class D commutation: This is also called as auxiliary commutation because it uses an auxiliary SCR to switch the charged capacitor across conducting SCR to turn it off. In this scheme, the main ... make SCR1 forward biased and keep ready for next triggering. The above cyclic process is repeated.

Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform.

Description : Draw the circuit diagram of bridge rectifier with π filter. Draw its input and output waveform. 

Last Answer : Circuit diagram of bridge rectifier with π filter : Input and output waveform:

Classify the power amplifiers on the basis of operation and input/output waveforms.

Description : Classify the power amplifiers on the basis of operation and input/output waveforms.

Last Answer : Depending upon the operation and input/output waveforms power amplifiers are classified into following type. 1) Class A amplifier. 2) Class B amplifier. 3) Class C amplifier. 4) Class AB amplifier. 5) Class D amplifier

Sketch the single tuned amplifier.

Description : Sketch the single tuned amplifier.

Last Answer : single tuned amplifier

The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, respectively. Calculate the equivalent input-noise resistance of this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Description : The first stage of a two-stage amplifier has a voltage gain of 10, a 600 Ω input resistor, a 1600Ω equivalent noise resistance and 27kΩ output resistor. For the second stage, these values are 25, 81kΩ, 19kΩ, and 1MΩ, ... this two stage amplifier. A. 2,518 kΩ B. 2,518 Ω C. 251.8 Ω D. 12,518 Ω

Last Answer : B. 2,518 Ω

In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Description : In the illustrated circuit, what is the phase relationship of the amplifier output compared to the input? EL-0022 A. 0° in-phase B. 180° out of phase C. phase angle of the input divided by power factor D. unable to determine without the value of the bias voltage

Last Answer : Answer: B

Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Description : Draw the block diagram of FM super heterodyne radio receiver with waveforms.

Last Answer : block diagram of FM super heterodyne radio receiver

The waveforms shown below are the input and output of an overdrive

Description : The waveforms shown below are the input and output of an overdrive

Last Answer : a. Cutoff. b. Saturation.

List the types of power amplifier.

Description : List the types of power amplifier.

Last Answer : Types of Power amplifier: 1) Class A power amplifier 2) Class B power amplifier 3) Class AB power amplifier 4) Class C power amplifier

List applications of power amplifier.

Description : List applications of power amplifier.

Last Answer : Below are the applications of power amplifiers across different sectors: 1.Consumer Electronics: Audio power amplifiers are used in almost all consumer electronic devices ranging from microwave ovens, ... data transfer rates and usability. They are also used in satellite communication equipment.

Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Description : Draw the labeled circuit of RC phase shift oscillator. State the formula for frequency of oscillator.

Last Answer : Frequency of oscillation is given by,

Draw the circuit and explain the operation of UJT relaxation oscillator.

Description : Draw the circuit and explain the operation of UJT relaxation oscillator. 

Last Answer : Working: When the supply voltage (VCC) is switched ON, the capacitor charges through resistor (R), till the capacitor voltage reaches the voltage level (VP) which is called as peak point voltage. At ... resistor R is shown as a variable resistor. The sweep period is given by the relation

Explain with circuit diagram and waveform the operation of class AB push pull power amplifier.

Description : Explain with circuit diagram and waveform the operation of class AB push pull power amplifier.

Last Answer : Class AB Push Pull Power Amplifier:  Circuit Diagram:  Circuit Decription: The circuit consists of two centre-tapped transformers T1 and T2, two identical transistors Q1 and Q2 , Resistor R and ... two halves & produces a full sine wave in the load resistor. Waveform :

Draw the circuit diagram for Instrumentation amplifier using three OP-AMPs. State its advantages and applications.

Description : Draw the circuit diagram for Instrumentation amplifier using three OP-AMPs. State its advantages and applications.

Last Answer : Application: 1. In Data acquisition from low output transducers such as strain gauges, Thermocouples, Wheatstone bridge measurements e.t.c 2. In Medical instrumentation, Navigation, Radar ... video data acquisition and imaging 5. High frequency signal amplification in cable RF systems 

The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Description : The circuit which changes input signal at output with phase shift of 1800 is called (a) Amplifier (b) operational amplifier (c) switch (d) inverter

Last Answer : (d) inverter

Draw diagram of class A push-pull amplifier and explain its operation.

Description : Draw diagram of class A push-pull amplifier and explain its operation. 

Last Answer : Class A Push-pull Amplifier: The circuit diagram of class A push-pull amplifier is as shown in the fig.(a). Operation: The resistors R1 and R2 along with Vcc provide the dc biasing so as ... Vcc is applied to the collectors of transistors Q1 and Q2 through the centretapped output transformer. 

If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Description : If the single-input, differential-output, differential amplifier has an output signal taken between the two output terminals, what will the peak-to-peak amplitude of this combined output be?

Last Answer : 200 millivolts. A-18. a. Differential amplifier

If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Description : If the differential amplifier is configured with a single input and differential outputs, what will the output signals be?

Last Answer : Each output will be a sine wave with a peak-to-peak amplitude of 100 millivolts. The output signals will be 180 degrees out of phase with each other.

What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?

Description : What two transistor amplifier configurations are combined in the single-transistor, two-input, single-output difference amplifier?

Last Answer : Common emitter (CE) and common base (CB)

With the help of circuit diagram and waveforms, explain working of RC differentiator.

Description : With the help of circuit diagram and waveforms, explain working of RC differentiator.

Last Answer : Fig: RC differentiating circuit Figure shows a RC differential circuit. It is also known as high pass filter. The reactance of a capacitor decreases with increasing frequency. The higher ... i.e. the output signal is directly proportional to the derivative of the input signal.  

The circuit shown in the illustration functions as a ____________. EL-0087 A. pulse trigger circuit for an operational amplifier B. three stage, high gain class 'A' amplifier C. binary ripple counter or shift register D. free running multivibrator

Description : The circuit shown in the illustration functions as a ____________. EL-0087 A. pulse trigger circuit for an operational amplifier B. three stage, high gain class 'A' amplifier C. binary ripple counter or shift register D. free running multivibrator

Last Answer : Answer: C

State and explain the working principle of FET amplifier and list its applications.

Description : State and explain the working principle of FET amplifier and list its applications.

Last Answer : Operation of FET amplifier: When small a.c. signal is applied to the gate, it produces variation in the gate to source voltage. This results in variation in the drain current. As ... input voltage.  Application: Buffer amplifier Low noise amplifier Cascade amplifier Chopper amplifier

State the need and types of amplifier coupling.

Description : State the need and types of amplifier coupling. 

Last Answer : Need of amplifier coupling: 1.When ever large amplifier with very good impedance matching is required, a signal stage amplifier circuit will not able to amplify the signal to a large extent. 2 ... 2.Transformer coupled amplifier 3.Direct coupled amplifier 4. Inductance (LC) coupling

Explain stagger tuned amplifier with the help of waveforms.

Description : Explain stagger tuned amplifier with the help of waveforms.

Last Answer : Circuit Diagram: Above figure shows two-stage tuned voltage amplifier. The stagger tuning in this circuit, may be achieved by resonating the tuned circuits L1C1 and L2C2 to slightly different ... outside the pass-band. Because of the stagger tuning there is a loss of voltage gain.