The unit of heat transfer co-efficient in SI unit is

(A) J/M2°K

(B) W/m2°K

(C) W/m°K

(D) J/m°K


1 Answer

Answer :

(B) W/m2°K

Related questions

Description : In SI units, fouling factor is expressed in (A) m2°K/W (B) W/m2°K (C) m2°K (D) m°K/W

Last Answer : (A) m2°K/W

Description : The unit of conductance in SI unit is (A) W/m (B) W/m2 (C) W/°K (D) W/m°K

Last Answer : (C) W/°K

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

Description : The unit of heat transfer co-efficient is (A) BTU/hr. ft 2°F (B) BTU/hr. °F. ft (C) BTU/hr. °F (D) BTU/hr. ft

Last Answer : (A) BTU/hr. ft 2°F

Description : Heat transfer rate per unit area is called (A) Thermal conductivity (B) Heat flux (C) Heat transfer co-efficient (D) Thermal diffusivity

Last Answer : (B) Heat flux

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

Description : The left face of a one dimensional slab of thickness 0.2 m is maintained at 80°C and the right face is exposed to air at 30°C. The thermal conductivity of the slab is 1.2 W/m.K and the heat transfer co-efficient from the ... temperature of the right face in °C is (A) 77.2 (B) 71.2 (C) 63.8 (D) 48.7

Last Answer : (D) 48.7

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

Description : The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2 .K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2 .K. The overall heat transfer co￾efficient ... 1200 W/m2 .K (B) 894 W/m2 .K (C) 333 W/m2 .K (D) 287 W/m2 .K

Last Answer : (C) 333 W/m2 .K

Description : What is the critical radius of insulation (cms) for a metallic cylinder, if the convective heat transfer co-efficient with the ambient atmosphere is 5 W/m2. °K? Thermal conductivity of metal and insulation material are 40 and 0.1 W/m.°K respectively. (A) 2 (B) 8 (C) 10 (D) 40

Last Answer : (A) 2

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

Description : What is the SI unit of specific heat capacity?  A. J/kg  B. J/kg °F ∙  C. J/kg °C ∙  D. J/°C

Last Answer : J/kg °C

Description : Which of the following is not a unit of mass transfer co-efficient? (A) Moles transferred/ [(time) (area) (mole fraction)] (B) Moles transferred/ [(time) (area) (mass A/mass B)] (C) Moles transferred/ [(time) (area) (pressure)] (D) None of these

Last Answer : (D) None of these

Description : An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Last Answer : (D) Be free from radiation damage and non-corrosive

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Description : . A dilute aqueous solution is to be concentrated in an evaporator system. High pressure steam is available. Multiple effect evaporator system is employed, because (A) Total heat transfer area of ... in a single effect is much lower than that in any effect in a multi-effect system

Last Answer : (B) Total amount of vapor produced per Kg of feed steam in a multiple effect system is much higher than in a single effect

Description : . In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Last Answer : (A) Infinity

Description : Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Last Answer : (B) Requirement of heat transfer area is low

Description : Heat transfer by natural convection is enhanced in system with (A) High viscosity (B) High co-efficient of thermal expansio

Last Answer : (B) High co-efficient of thermal expansion

Description : Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Last Answer : (C) Heat transfer co-efficient

Description : As the difference between the wall temperature and bulk temperature increases, the boiling heat transfer co-efficient (A) Continues to increase (B) Continues to decrease (C) Goes through a minimum (D) Goes through a maximum

Last Answer : (C) Goes through a minimum

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

Description : Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient ... ) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Last Answer : (B) Vertical heat exchanger with steam on shell side

Description : Log mean temperature difference (LMTD) cannot be used, if (A) Heat transfer co-efficient over the entire heat exchanger is not constant (B) There exists an unsteady state (C) The heat capacity is not constant and there is a phase change (D) None of these

Last Answer : (D) None of these

Description : Controlling heat transfer film co-efficient is the one, which offers __________ resistance to heat transfer. (A) No (B) The least (C) The largest (D) Lower

Last Answer : (C) The largest

Description : Steam side heat transfer co-efficient in an evaporator is in the range of __________ kcal/hr.m2°C. (A) 10-50 (B) 100-500 (C) 1000-1500 (D) 5000-15000

Last Answer : (D) 5000-15000

Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Last Answer : (C) Increase the shell side heat transfer co-efficient

Description : For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus-Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of (A) 1 (B) 1.74 (C) 6.1 (D) 37

Last Answer : (C) 6.1

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

Description : Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Last Answer : (D) > 10000

Description : Heat transfer co-efficient (h1 ) for liquids increases with (A) Increasing temperature (B) Decreasing temperature (C) Decreasing Reynolds number (D) None of these

Last Answer : (A) Increasing temperature

Description : Heat exchangers operating, when the asymptotic range is reached, (A) Provide very large heat transfer co-efficient (B) Results in making part of the heating surface inactive (C) Results in abruptly increased velocity (D) None of these

Last Answer : (B) Results in making part of the heating surface inactive

Description : The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Last Answer : (B) 4 0.8

Description : If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Last Answer : (B) Always between h1 and h2

Description : The main purpose of providing fins on heat transfer surface is to increase the (A) Temperature gradient (B) Mechanical strength of the equipment (C) Heat transfer area (D) Heat transfer co-efficient

Last Answer : (C) Heat transfer area

Description : Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Last Answer : (D) All (A) (B) and (C)

Description : Overall heat transfer co-efficient of a particular tube is U1 . If the same tube with some dirt deposited on either side has coefficient U2 , then (A) U1 = U2 (B) U2 > U1 (C) U1 > U2 (D) U1 = dirt factor - U2

Last Answer : (A) U1 = U2

Description : The advantage of using a 1 - 2 shell and tube heat exchanger over a 1 - 1 shell and tube heat exchanger is (A) Lower tube side pressure drop (B) Lower shell side pressure drop (C) Higher tube side heat transfer co-efficient (D) Higher shell side heat transfer co-efficient

Last Answer : (C) Higher tube side heat transfer co-efficient

Description : Indirect contact heat exchangers are preferred over direct contact heat exchangers, because (A) Heat transfer co-efficient are high (B) There is no risk of contamination (C) There is no mist formation (D) Cost of equipment is lower

Last Answer : (B) There is no risk of contamination

Description : Which of the following has the lowest overall heat transfer co-efficient? (A) Dowtherm (B) Molten sodium (C) Water (D) Air

Last Answer : (D) Air

Description : The maximum heat transfer co-efficient from steam heating will beattained when the steam is: (A) Supersaturated (B) Saturated (C) Wet (D) None of these

Last Answer : (B) Saturated

Description : The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient ... pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Last Answer : (B) D-0.2

Description : Multipass heat exchangers are used (A) Because of simplicity of fabrication (B) For low heat load (C) To obtain higher heat transfer co-efficient and shorter tube (D) To reduce the pressure drop

Last Answer : (C) To obtain higher heat transfer co-efficient and shorter tube

Description : Extremely large or small volumes of fluids are generally best routed through the shell side of a shell and tube heat exchanger, because of the (A) Less corrosion problems (B) Flexibility possible in the baffle arrangement (C) Low pressure drop (D) High heat transfer co-efficient

Last Answer : (B) Flexibility possible in the baffle arrangement

Description : The average heat transfer co-efficient over the entire length of the plate (ha ) and the local heat transfer co-efficient (hL ), in case of heat transfer over a flat plate in laminar zone is related as (A) ha = 0.8hL (B) ha = 2hL (C) ha = hL (D) ha = 5hL

Last Answer : (B) ha = 2hL

Description : The heat transfer co-efficient in film type condensation is __________ that for dropwise condensation. (A) Greater than (B) Lower than (C) Is same as (D) Half

Last Answer : (B) Lower than

Description : In a shell and tube heat exchanger, floating head is used for (A) Large temperature differentials (B) High heat transfer co-efficient (C) Low pressure drop (D) Less corrosion of tubes

Last Answer : (A) Large temperature differentials

Description : In Fourier's law, the proportionality constant is called the (A) Heat transfer co-efficient (B) Thermal diffusivity (C) Thermal conductivity (D) Stefan-Boltzmann constant

Last Answer : (C) Thermal conductivity