Please Log in or Register for more.

what is firing angle?

what is firing angle?

155 views

asked Dec 7, 2017 by anonymous

2 Answers

Answer :

Firing angle is the angle at which the sin angle is delaying to start the waveform.

answered Dec 7, 2017 by Jeevanprasath

Answer :

Firing angle is time in electrical degrees from the instant the valve voltage is positive to the application of firing pulse to the valve (start of conduction). Also called delay angle.

answered May 22, 2018 by Neha8235

Please log in or register to answer this question.

Related Questions

Define: i) Firing angle ii) Conduction angle

Define: i) Firing angle ii) Conduction angle
Last Answer : (i) Conduction Angle (β): Conduction angle is defined as the angle between the instant the SCR is triggered or turned on and the instant at which the SCR is turned off. Assuming that the SCR ... maximum average output voltage to the angle when the SCR is actually triggered or fired by gate pulse.

4.0k views 2 answers

asked Sep 16, 2019 by anonymous

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a

When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is
Last Answer : When the firing angle a of a single-phase, fully controlled rectifier feeding constant direct current into a load is 30°, the displacement power factor of the rectifier is √3/2

1.4k views 1 answer

asked Apr 29, 2018 by anonymous

What is meant by firing angle of thyristor?

What is meant by firing angle of thyristor?
Last Answer : The point at which SCR is triggered is known as firings angle of thyristor.

230 views 1 answer

asked Mar 19, 2018 by anonymous

Explain the concept of lagging and leading phase angle by waveform.

Explain the concept of lagging and leading phase angle by waveform.
Last Answer : i) Leading phase angle : When two ac quantities of same frequency do not attain their respective zero or peak values simultaneously, then the quantities are said to be out-of-phase quantities. The ... Similarly, in the second diagram, the voltage is said to be lagging the current by Φ.

378 views 1 answer

asked Apr 27, 2020 by anonymous

How to find total impedance Z, current I and Impedance angle ?

How to find total impedance Z, current I and Impedance angle ?
Last Answer : How to find total impedance Z, current I and Impedance angle ?

165 views 2 answers

asked May 30, 2019 by anonymous

Phase margin is the amount of angle to make the system

Phase margin is the amount of angle to make the system (1) Oscillatory (2) Stable (3) Unstable (4) Exponential
Last Answer : Phase margin is the amount of angle to make the system Unstable

202 views 1 answer

asked Apr 30, 2018 by anonymous

The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu

The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu from a lagging load are 45o and 15o, respectively. The direct axis and quadrature axis currents, respectively, are (A) 0.5 pu ... pu, 0.5 pu (C) 0.707 pu, 0.707 pu (D) 0.5 pu, 0.5 pu
Last Answer : The power factor angle and torque angle of a salient pole synchronous generator drawing a current of 1.0 pu from a lagging load are 45o and 15o, respectively. The direct axis and quadrature axis currents, respectively, are 0.866 pu, 0.5 pu

97 views 1 answer

asked Apr 28, 2018 by anonymous

Torque angle for the synchronous machine is the angle between

Torque angle for the synchronous machine is the angle between (A) stator magnetic field and rotor magnetic field (B) stator magnetic field and net magnetic field in the air gap (C) rotor magnetic field and net magnetic field in the air gap (D) excitation voltage and impedance voltage drop
Last Answer : Torque angle for the synchronous machine is the angle between rotor magnetic field and net magnetic field in the air gap

129 views 1 answer

asked Apr 28, 2018 by anonymous

The product of apparent power and cosine of the phase angle between circuit voltage and current is?

The product of apparent power and cosine of the phase angle between circuit voltage and current is?
Last Answer : In parllpar reasonans RLC circuit the current is

647 views 2 answers

asked Mar 25, 2018 by anonymous

What will be the phase angle between two alternating waves of equal frequency...

What will be the phase angle between two alternating waves of equal frequency, when one wave attains maximum value the other is at zero value ?
Last Answer : 90° will be the phase angle between two alternating waves of equal frequency, when one wave attains maximum value the other is at zero value.

645 views 1 answer

asked Mar 25, 2018 by anonymous

The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of______degrees.

The r.m.s. value of a sinusoidal A.C. current is equal to its value at an angle of______degrees.
Last Answer : 45

838 views 2 answers

asked Mar 24, 2018 by anonymous

Two waves of the same frequency have opposite phase when the phase angle between them is?

Two waves of the same frequency have opposite phase when the phase angle between them is?
Last Answer : Two waves of the same frequency have opposite phase when the phase angle between them is 180°.

776 views 1 answer

asked Mar 24, 2018 by anonymous

Tangent of angle of friction is equal to?

Tangent of angle of friction is equal to?
Last Answer : Tangent of angle of friction is equal to coefficient of friction.

622 views 1 answer

asked Mar 22, 2018 by anonymous

Angle of friction is the?

Angle of friction is the?
Last Answer : Angle of friction is the angle between normal reaction and the resultant of normal reaction and the limiting friction.

86 views 1 answer

asked Mar 22, 2018 by anonymous

If the current in a capacitor leads the voltage by 80°, the loss angle of the capacitor is?

Last Answer : If the current in a capacitor leads the voltage by 80°, the loss angle of the capacitor is 10°.

219 views 1 answer

asked Mar 21, 2018 by anonymous

The coupling angle or load angle of synchronous motor is defined as the angle between the?

Last Answer : The coupling angle or load angle of synchronous motor is defined as the angle between the rotor and the stator poles of opposite polarity.

218 views 1 answer

asked Mar 20, 2018 by anonymous

What is the maximum value of torque angle in synchronous motor?

What is the maximum value of torque angle in synchronous motor?
Last Answer : The maximum value of torque angle in synchronous motor is 90 degrees electrical.

1.5k views 1 answer

asked Mar 18, 2018 by anonymous

The synchronous motor will develop maximum power when the load angle is?

The synchronous motor will develop maximum power when the load angle is?
Last Answer : The synchronous motor will develop maximum power when the load angle is 900.

223 views 1 answer

asked Mar 18, 2018 by anonymous

What is power factor angle?

What is power factor angle?

67 views 0 answers

asked Mar 10, 2018 by anonymous

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load,

In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is (A) sinusoidal current (B) constant dc current (C) continuous rectangular pulses (D) alternating rectangular pulses
Last Answer : In a 230 V, 50 Hz single-phase SCR bridge converter operating at a firing delay angle, α and with large R-L load, the input source current is alternating rectangular pulses

177 views 1 answer

asked Apr 28, 2018 by anonymous

After firing as SCR, the gating pulse is removed. The current in the SCR will

After firing as SCR, the gating pulse is removed. The current in the SCR will 1. remain the same 2. immediately fall to zero 3. rise up 4. None
Last Answer : After firing as SCR, the gating pulse is removed. The current in the SCR will remain the same

108 views 1 answer

asked May 13, 2018 by anonymous

What is the control range of firing angle inac voltage controller with RL load?

What is the control range of firing angle inac voltage controller with RL load?
Last Answer : The control range is Φ< α

10 views 1 answer

asked Dec 28, 2021 by itszee

What is delay angle or what is firing angle of phase controlled rectifier?

What is delay angle or what is firing angle of phase controlled rectifier?
Last Answer : The delay angle is the angle at which thyristors are triggered after zero crossing. After zero crossing of supply voltage, one pair of thyristors is forward biased. After delay angle(α) these SCRs are triggered.

15 views 1 answer

asked Dec 28, 2021 by itszee

What is firing angle?

What is firing angle?
Last Answer : The angle between the zero crossing of the input voltage and the instant the SCR is fired is called as delay angle or firing angle.

2 views 1 answer

asked Dec 28, 2021 by itszee

What is firing angle?

What is firing angle?
Last Answer : The angle in the AC cycle at which the thyristor starts conducting at the application of positive voltage to gate is known as the firing angle (α)

5 views 1 answer

asked Nov 18, 2021 by itszee

Regenerative breaking of ac-dc converter fed dc motor is possible when firing delay angle of SCRs is

Regenerative breaking of ac-dc converter fed dc motor is possible when firing delay angle of SCRs is (A) 30° (B) 60° (C ) 90° (D) 120°

64 views 0 answers

asked Jun 4, 2018 by anonymous

A separately excited d.c. motor fed from single phase full converter with firing angle 60° runs at 1000 r.p.m.

A separately excited d.c. motor fed from single phase full converter with firing angle 60° runs at 1000 r.p.m. If motor is connected to single phase semiconverter with the same firing angle of 60°, it would run at (a) 2000 rpm (b) 1850 rpm (c) 1500 rpm (d) 1000 rpm
Last Answer : Ans =1500

1.3k views 3 answers

asked May 25, 2018 by anonymous

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25 and an

A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is (A) 0.78 (B) 0.827 (C) 0.866 (D) 0.9
Last Answer : A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25o and an overlap angle of 10o with constant dc output current of 20 A. The fundamental power factor (displacement factor) at input ac mains is 0.78

559 views 1 answer

asked May 18, 2018 by anonymous

In static Kramer drive, motor turns ratio is 0.6, the firing angle is 120o. The motor slip is

In static Kramer drive, motor turns ratio is 0.6, the firing angle is 120o. The motor slip is (a) 0.633 (b) 0.533 (c) 0.833 (d) 0.733
Last Answer : In static Kramer drive, motor turns ratio is 0.6, the firing angle is 120o. The motor slip is 0.833

225 views 1 answer

asked May 13, 2018 by anonymous

A single phase fully controlled thyristor bridge ac -dc converter is operating at a firing angle of 25 degree...

A single phase fully controlled thyristor bridge ac -dc converter is operating at a firing angle of 25 degree and an overlap angle 10 degree with constant dc output current of 20A. The fundamental power factor (displacement factor) at input ac mains is : (A) 0.78 (B) 0.827 (C) 0.866 (0) 0.9

158 views 0 answers

asked Apr 14, 2018 by anonymous

If firing angle in SCR increases, output is - - -

Last Answer : If firing angle in SCR increases, output is Decreases

127 views 1 answer

asked Mar 29, 2018 by anonymous

Should condemned prisoners have the choice of how they die? Would you choose the option to die by firing squad?

Should condemned prisoners have the choice of how they die? Would you choose the option to die by firing squad?
Last Answer : Can you really call it a choice, if one of the choices is not “to die of old age”?

1 view 1 answer

asked Mar 5 by anonymous

Is president Trump firing people for superficial reasons?

Is president Trump firing people for superficial reasons?
Last Answer : Scaramoucci can’t spell Scaramucci…oops, maybe that’s why he’d no longer with us!!!

0 views 1 answer

asked Mar 2 by anonymous

What is your opinion, of a world leader discrediting, or firing all the people who investigate their potential crimes?

What is your opinion, of a world leader discrediting, or firing all the people who investigate their potential crimes?
Last Answer : At first I thought you might be referring to your President, but that “world leader” thing eliminates that possibility. In any event, it’s a predictable reflex.

0 views 1 answer

asked Mar 2 by anonymous

Whats your theory behind the Scaramucci firing?

Whats your theory behind the Scaramucci firing?
Last Answer : Hey! Little Tony’s a mechanic. Mechanics do dat.

0 views 1 answer

asked Mar 2 by anonymous

Why is Trump visiting the Russian ambassador today, one day after the firing of James Comey?

Why is Trump visiting the Russian ambassador today, one day after the firing of James Comey?
Last Answer : To tell them to look out for trouble? To get more political advice?

0 views 1 answer

asked Mar 2 by anonymous

Did Cobert intend his audience to cheer about the firing of James Comey?

Did Cobert intend his audience to cheer about the firing of James Comey?
Last Answer : Yellowdog i think he was shocked by the cheering.

0 views 1 answer

asked Mar 2 by anonymous

How suspicious does this look? A day after firing Comey for investigating the Russia connection, Trump is meeting the Russian Foreign Minister?

How suspicious does this look? A day after firing Comey for investigating the Russia connection, Trump is meeting the Russian Foreign Minister?
Last Answer : All I can say is, the man thinks because he’s the president he can do anything and no one has the right to object. Therefore he doesn’t need to hide anything.

1 view 1 answer

asked Mar 2 by anonymous

Okay it is real now, what do you think of Trump firing 50 or 60 missiles in Syria?

Okay it is real now, what do you think of Trump firing 50 or 60 missiles in Syria?
Last Answer : Promise kept. He said he would never speak of military actions in advance. I think he made the right move. It was an action which called for an ass-kick. He’s a dog that bites with no warning bark. Bam! Don’t frick with that.

0 views 1 answer

asked Mar 2 by anonymous

Do you think North and South Korea firing shots at each other's boats today is the start to World War III?

Do you think North and South Korea firing shots at each other's boats today is the start to World War III?
Last Answer : No, it has been happening off and on for years. China is getting pretty tired of N Korea as a client state, and will quite likely tell Pyongyang to knock it off if it ever gets dire.

0 views 1 answer

asked Feb 28 by anonymous

How many chances do you give someone before firing them?

How many chances do you give someone before firing them?
Last Answer : answer:3 for a minor infraction 1 for a major infraction

0 views 1 answer

asked Feb 27 by anonymous

Does anyone else find it ironic that Republicans are bashing Romney for talking about firing bad insurance companies?

Does anyone else find it ironic that Republicans are bashing Romney for talking about firing bad insurance companies?
Last Answer : answer:No, not ironic so much as disheartening. Not really doing anybody any favors with the mud-slinging. That said, Romney should know better than to leave any word or phrase to chance. Statesmanship is ... impact of words on listeners and I think he's not too bright for leaving that to chance.

0 views 1 answer

asked Feb 27 by anonymous

What, besides coefficient of expansion, could make two pieces of glass incompatible for firing together?

What, besides coefficient of expansion, could make two pieces of glass incompatible for firing together?
Last Answer : Melting point would be my guess. The Fuseworks is for microwave kiln use.

0 views 1 answer

asked Feb 27 by anonymous

Firing glass in a kiln: can a piece be fired twice?

Firing glass in a kiln: can a piece be fired twice?
Last Answer : Yes. Firing at these low temperatures doesn’t make any fundamental change in the structure of the glass.

0 views 1 answer

asked Feb 27 by anonymous

What do you think of NPR's firing of host Juan Williams for stating his opinion which is a fear of Muslims being on the same plane with him?

What do you think of NPR's firing of host Juan Williams for stating his opinion which is a fear of Muslims being on the same plane with him?
Last Answer : It was a totally inappropriate comment for a professional journalist to say, and he deserved to be at least reprimanded. NPR very carefully tries to keep itself above controversy. They also told their members to stay away from the Colbert/Stewart rally.

0 views 1 answer

asked Feb 27 by anonymous

Do you think that firing House's original team(Cameron,Chase and Foreman)was a bad move(from the TV show House MD)

Do you think that firing House's original team(Cameron,Chase and Foreman)was a bad move(from the TV show House MD)
Last Answer : I love House. No I think it was a good idea. It brought new character’s in and made the plot shift and exciting to me. One of the new character committed suicide. I just watched the rerun.

0 views 1 answer

asked Feb 27 by anonymous

State of Utah uses firing squad to execute a killer. any comments?

State of Utah uses firing squad to execute a killer. any comments?
Last Answer : All methods of capital punishment are very distressing. I’m from PA so Utah seems like a very strange place to begin with. We apparently have the death penalty but according to deathpenaltyinfo.org, the state has only executed three people since 1976. Super creepy. At least he got to choose, huh?

0 views 1 answer

asked Feb 27 by anonymous

Would you face the firing squad?

Would you face the firing squad?
Last Answer : answer:It’s more exciting, I suppose. Besides, maybe he’s scared of needles. I’d choose lethal injection, if I had to. I’ve always been fascinated whenever I get shots. May as well go out with something I know I’m cool with.

0 views 1 answer

asked Feb 27 by anonymous

How far would you go to protect a fellow worker, wrongfully accused of something, resulting in their firing?

How far would you go to protect a fellow worker, wrongfully accused of something, resulting in their firing?
Last Answer : answer:I would stick up for them in the sense that I wouldn't mind telling HR I know what happened and they are innocent. I wouldn't go any further than that though b/c I'm not risking my ... aren't many well paying jobs out there right now. And I wouldn't expect anything more of that friend.

1 view 1 answer

asked Feb 27 by anonymous

In NYS shouldn't they at least give you some sort of heads up when firing an employee?

In NYS shouldn't they at least give you some sort of heads up when firing an employee?
Last Answer : answer:Morally, of course they should. Legally, absolutely not. NYS is an at-will state. The employer is under no obligation to give you any hours, ever, and can terminate entirely at his or her discretion.

0 views 1 answer

asked Feb 27 by anonymous

Show More ⇦ Previous Next ⇨