Please Log in or Register for more.

parallel operation of MOSFET can be done more easily as compared to thyristor. why?

300 views

1 Answer

Answer :

 
✔️✔️Best answer
Parallel operation of MOSFET can be done more easily as compared to thyristor because the resistance of MOSFET is increases with increase in temperature. MOSFET have the positive temperature coefficient. In positive temperature coefficient, the resistance increases with increase in temperature and in case of negative temperature coefficient resistance decrease with increase in temperature. Due to the positive temperature coefficient of MOSFET if we connect MOSFET in parallel and if the current in particular MOSFET increases then due to losses the temperature in that particular MOSFET will be increased. This increase in temperature will also increase the internal resistance of that particular MOSFET, therefore, the current in that particular MOSFET will also decrease this thing will balance the current in MOSFETs.

But in case of a thyristor which is a negative temperature coefficient device. So due to negative temperature coefficient, the resistance in the thyristor will decrease when the temperature of thyristor will increase this causes more current to flow due to low resistance.Hence the parallel operation of MOSFET can be done more easily as compared to the thyristor.
Like 0 like

Please log in or register to answer this question.

Related Questions


Explain the series and parallel operation of MOSFET. Which is suitable and why?
Last Answer : Series operation of MOSFET: To increase voltage handling capability MOSFETs are connected in series. When the MOSFETs are connected in series each MOSFET should turn on and turn off ... on and turn off time and transconductance. Each MOSFET should share current equally.  

Show More

534 views 1 answer







An additional condition for parallel operation of three-phase transformers over single-phase transformers is that
Last Answer : An additional condition for parallel operation of three-phase transformers over single-phase transformers is that the transformers should belong to the same vector group

Show More

144 views 1 answer







Also, highlight the problem faced during parallel operation.
Last Answer : Parallel operation of IGBT: Parallel operation of IGBT is done for obtaining high current rating. Paralleling of IGBT reduces conduction losses and thermal stress. IGBT combines the qualities of ... . IGBTs must share losses equally otherwise IGBT may get failure due to thermal differences.

Show More

223 views 1 answer







Describe the operation of N channel enhancement type MOSFET with diagram.
Last Answer : As its name indicates, this MOSFET operates only in the enhancement mode and has no depletion mode. It operates with large positive gate voltage only. It does not conduct when the ... of charge carriers attracted to the positive gate. Thus drain current is controlled by the gate potential.

Show More

636 views 1 answer








Last Answer : For the parallel operation of two or more D.C. compound generators, we should ensure that series fields of all generators should be either on positive side or negative side of the armature.

Show More

179 views 1 answer








Last Answer : Necessary conditions required to be satisfied in order to ensure successful parallel operation of single phase transformers:  1. Only transformers having the same phase displacement between primary and secondary ... . 7. The phase sequence must be followed strictly on HV and LV side connection.

Show More

197 views 2 answers







Thyristor can be protected from over voltages by using
Last Answer : Thyristor can be protected from over voltages by using Voltage clamping device

Show More

107 views 1 answer







Leakage current flows through the thyristor in
Last Answer : Leakage current flows through the thyristor in Forward blocking mode and Reverse blocking mode.

Show More

211 views 1 answer







What is a phase control thyristor?

Show More

153 views 0 answers







Why thyristor are not preferred for inverter?

Show More

454 views 0 answers







What is thyristor family?

Show More

67 views 0 answers







What is meant by firing angle of thyristor?
Last Answer : The point at which SCR is triggered is known as firings angle of thyristor.

Show More

230 views 1 answer







What is the use of a thyristor in a circuit?

Show More

2.9k views 0 answers







What is a reverse conducting thyristor?

Show More

84 views 0 answers







What is the function of a thyristor?

Show More

92 views 0 answers







Why SCR is called as thyristor?

Show More

97 views 0 answers







Is a SCR a thyristor?
Last Answer : Yes, SCR is a thyristor. Thyristor is the family and SCR is the member of that family but SCR is universally known as thyristor.

Show More

161 views 1 answer







How is a thyristor used to convert AC to DC?
Last Answer : thyristor

Show More

123 views 1 answer







What is the application of thyristor?

Show More

90 views 0 answers








Last Answer : Yes ,it is one of the main advantage using thristors as a  switch in DC  circuit ,it has a high current gain

Show More

160 views 2 answers







Explain thyristor gate drive circuit.
Last Answer : Thyristor Gate Drive Circuit: The thyristor can be turned on by pulse voltage signal at gate terminal and it does not require continuous drive signal like the transistor. The gate ... circuit provide required minimum gate voltage and gate current then the thyristor conducts properly.

Show More

3.0k views 1 answer







what are the disadvantages of thyristor?
Last Answer : Disadvantages of thyristor The silicon controlled rectifier (SCR) is unidirectional devices, so it can control power only in DC power during positive half cycle of AC supply. Thus only DC power is ... cycle. It cannot be used at higher frequencies. The gate current cannot be negative

Show More

886 views 2 answers







write short notes on thyristor CSI .
Last Answer : Current-source inverter (CSI) is an inverter with a DC current input. Current source inverters are most commonly used in very high power AC motor drives.

Show More

107 views 2 answers







Draw the structural diagram of GTO. Explain briefly the switching behavior of GTO with the help of appropriate voltage and current waveform.
Last Answer : Gate Turn Off Thyristor (GTO) Conventional Thyristor can be turned on with gate terminal but can not turn off from gate terminal. But in case of Gate Turn Off Thyristor (GTO), we can turn it on and off ... subdivided as storage period (Ts), fall period (Tp) and tail period (Tt).

Show More

1.7k views 1 answer







Describe with neat sketch the construction and working principle of MOSFET.
Last Answer : Construction and working principle of MOSFET:  A) Depletion type MOSFET: Construction: The N-channel depletion type MOSFET is formed on P-type silicon substrate with two heavily ... accumulation of electrons and hence more current. Thus the MOSFET is a gate voltage controlled device.

Show More

3.6k views 1 answer







State the applications of MOSFET
Last Answer : Applications of MOSFET: i) Switching-mode-power-supplies (SMPS) and linear power supplies. ii) Brushless DC motor drives iii) Solid state DC relay iv) Automobile applications v) Stepper motor controller vi) Lighting controls vii) Solenoid drivers viii) Robotics ix) Induction heating

Show More

87 views 1 answer







The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at a gate voltage of 3V. Pinch off would be occurs at a drain voltage of (A) 1.5V (B) 2.5V (C) 3.5V (D) 4.5V
Last Answer : The threshold voltage of an n- channel enhancement mode MOSFET is 0.5V when the device is biased at a gate voltage of 3V. Pinch off would be occurs at a drain voltage of 2.5V

Show More

314 views 1 answer







Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown
Last Answer : Which phenomenon is present in thyristors but absent in BJT, MOSFET and IGBT ? (A) forward conduction (B) latching (C) forward blocking (D) reverse breakdown

Show More

3.2k views 1 answer







Explain switching model of MOSFET.

Show More

75 views 0 answers







Explain MOSFET gate drive circuit and totem pole configuration.
Last Answer : MOSFET gate drive circuit: The turning on and turning off of MOSFET can be controlled from gate to source voltage signal. If the gate to source voltage of MOSFET exceeds threshold ... this configuration, the two switches (transistors) are used in totem pole arrangement with a comparator.

Show More

348 views 1 answer







Explain the formation of parasitic BJT and parasitic diode in Power MOSFET. Can parasitic diode be used in same power electronics applications?
Last Answer : Parasitic Diode: The parasitic diode is in between drain and source. The MOSFET structure itself contains parasitic diode or body drain diode. This parasitic diode allows the reverse flow of current when the ... of MOSFET as a BJT collector. Parasitic BJT operates in the cut-off region.

Show More

2.6k views 1 answer







Operating frequency of power MOSFET is higher than that of power BJT. Justify the statement.
Last Answer : Power MOSFET have high turning on and turning off capability high switching speed of MOSFET is due to the high rate of change of drain voltage. The switching losses of power MOSFET ... lower frequency. Hence, operating frequency of power MOSFET is higher than that of power BJT.

Show More

983 views 1 answer







Justify the statement. Antiparallel diode is connected across MOSFET.
Last Answer : In MOSFET current is flow from drain to source but when the load is inductive the current may flow in opposite direction. To avoid the opposite flow of current and to protect MOSFET the antiparallel diode is connected across MOSFET.

Show More

160 views 1 answer







Justify. Power MOSFET is operated at high enough gate source voltage to minimize the conduction losses. 
Last Answer : MOSFET is metal oxide field effect transistor. MOSFET is a voltage controlled device. MOSFET is majority carrier device. MOSFET are of two one is n-channel MOSFET and p-channel MOSFET. Gate, ... . Hence, power MOSFET is operated at high enough gate-source voltage to minimize the conduction losses.

Show More

842 views 1 answer







Explain difference between enhancement MOSFET and depletion type MOSFET.
Last Answer : In enhancement MOSFET channel is not initially exists but in depletion MOSFET channel is already exists. In case of depletion MOSFET if the voltage is applied between drain and source the drain current will flow ... a channel. depletion MOSFET & enhancement MOSFET

Show More

548 views 1 answer







Compare BJT, MOSFET and IGBT .
Last Answer : BJT MOSFET IGBT BJT is a current controlled device. MOSFET is a voltage controlled device. IGBT is a voltage controlled device. The input impedance of BJT is low. ... is minority carrier device. MOSFET is majority carrier device. IGBT is minority carrier device.

Show More

448 views 1 answer








Last Answer : Because it has a higher switching frequency and heat tolerance.

Show More

143 views 1 answer







What is depletion type MOSFET?..........
Last Answer : Depletion MOSFET: Depletion MOSFET is a MOSFET in which the channel already exists. If we apply a voltage between drain and source then the drain current will flow even if the gate to source ... in figure. The drain current will be reduced as the gate to source voltage made more negative.

Show More

188 views 1 answer







What is enhancement MOSFET?...............
Last Answer : Enhancement MOSFET: There are two types of MOSFET one is enhancement MOSFET and second is depletion MOSFET. In enhancement MOSFET channel is created by applying threshold voltage between gate and source ... mode. The enhancement MOSFET will not conduct if the gate to source voltage is zero.

Show More

175 views 1 answer








Last Answer : ON state losses of IGBT is less as compared to MOSFET and BJT.

Show More

141 views 1 answer








Last Answer : No, MOSFET is not the curent controlled device. The current between drain and source which is drain current is controlled by applying a voltage between gate and source hence MOSFET is a voltage controlled device. 

Show More

201 views 1 answer








Last Answer : already answered here is mosfet current controlled device?

Show More

172 views 1 answer








Last Answer : MOSFET provides better efficiency at high frequency and its high speed switching losses are less hence MOSFET is used for high frequency.

Show More

114 views 1 answer







With neat sketch explain four modes of operation of a TRIAC? 
Last Answer : Modes of operation of a TRIAC: There are four different operating modes of TRIAC:  1) MT2 and gate are positive with respect to terminal MT1(Mode1) : Here terminal MT2 is positive ... junction P2-N2 is forward biased, current carriers are injected and therefore, the TRIAC is turned on. 

Show More

442 views 1 answer







Explain the operation of UPS with a neat block diagram.
Last Answer : Uninterruptible-Power-Supplies (UPS): A block diagram of UPS system is shown in figure. It essentially consists of four major components: i)Rectifier (or battery charger) ii) ... . Due to fast action requirement, transfer switch can be implemented by fast acting semiconductor devices.

Show More

3.3k views 1 answer







Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO 
Last Answer : Which of the following thyristors can be used for high frequency of operation? A) TRIAC B) DIAC C) SCR D) GTO 

Show More

109 views 1 answer







A four -quadrant operation requires two full converters connected in  (1) Series (3) Back to back (2) Parallel (4) Series Cascade
Last Answer : A four-quadrant operation requires two full converters connected in Parallel 

Show More

883 views 1 answer







Describe the working principle of Thyristor operated dimmer with the help of circuit diagram.
Last Answer : Thyristor operated dimmer: A popular thyristor operated dimmer circuit employ TRIAC-DIAC phase control for low AC power control. During each half-cycle, the capacitor charges through (R1+VR1). When the ... time constant {C (R1+VR1)}. Thus by reducing VR1 the lamp brightness can be increased.

Show More

368 views 1 answer








Last Answer : By using some circuit the forward DC current of thyristor is forced to zero is called forced commutation.

Show More

115 views 1 answer








Last Answer : Natural commutation is also called as line Communication. The turning off of thyristor due to AC supply is called natural commutation or line commutation. If the thyristor is connected to AC supply ... connected to positive and anode terminal get connected to negative, this turns off the thyristor.

Show More

108 views 1 answer






Show More⇦ PreviousNext ⇨